How to adjust your Blow-off valve?

Want to instantly increase the performance of your vehicle? In this video, we'll show you all the tricks to adjust your blow-off valve and get the most out of it! From understanding the basics to getting expert tips, you don't want to miss this one. Tune in now and learn how to adjust your BOV for maximum results! 💪🔥
Adjust Your Blow-Off Valve in Just 3 Simple Steps!
- www.turbosmart.com/news/3-qui...
SUPPORT & WARRANTY
- support.turbosmart.com/portal...
SUPPORT OUR CHANNEL
Don't forget to BOOST that like button, subscribe, and ring the bell to join our community of turbocharged enthusiasts who share the same passion for innovative turbo technology 🚀🔔
ABOUT TURBOSMART
Explore turbo technology with Turbosmart, a global leader in the field. Our in-house engineers craft high-quality blow-off valves, wastegates, boost controllers, and more, trusted by high-performance drivers worldwide. Committed to excellence, Turbosmart is shaping the future of turbo technology for both track and street applications. #keeponbuilding
FIND US AT
- www.turbosmart.com/
SHOP ALL TURBOSMART PRODUCTS 🤑
- www.turbosmart.com/shop/
CONTACT US AT
- support.turbosmart.com/portal...
FOLLOW US ON SOCIAL 😉
- Follow us on TikTok: / turbosmarthq
- Like us on Facebook: / turbosmart
- Follow us on Instagram: / turbosmarthq
- Follow us on LinkedIn: / turbosmart

[@winston9055]

Thank goodness for this video, I got my c63s running a full Stage 2 tune with these mechanical bov, I swear on the hardest setting my car would surge on the top end but found this video…. Set them on the softest setting and the car runs way better, the surge went away from what I can tell

[@AfriqueNY]

Thank you. Great videos

[@chriiss6936]

Is the mk6 dual port plug and play adjustable too?

[@AndrewMurphy8383]

great video

[@TurbosmartHQ]

Thanks!

[@Al-nt5fh]

Ok great video I wish u detailed if factory setting is better or loose and also wish u demonstrated with compressed air so we can hear the difference

[@TurbosmartHQ]

The adjustment will not effect how the valve sounds when it releases pressure. The adjustment is there to assist in how the valve operates. The audible level of the valve is dependent on the amount of pressure your application makes and the size of the orifice the pressure releases out of (Smaller = Louder)

[@TuneboyR]

Can i set it up a tad harder to have flutter under light boost? Would that be a possible thing? Or is it only for idle reference? Thanks

[@TurbosmartHQ]

Increasing spring tension can induce flutter at lower boost levels but it all really depends on your engine vacuum level.

[@bosnow9221]

Hello. I recently bought a vee port pro. I have adjusted all the way soft but I’m still not getting much boost relief. I opened it up and I think it came with a white spring.. is the spring to heavy for my 17lbs of boost ? Thanks. Cheers 🍻

[@TurbosmartHQ]

For BOVs, the springs are rated for Vacuum, rather than boost levels (wastegates are rated on boost). If you need help configuring your valve, feel fee to reach out to us directly Turbosmart.com/contact-us OR each of our regional office's phone numbers are listed at the bottom of the page as well 👍 Happy to help!

[@pigeonsil240sx]

i have a sr20det and upgraded the turbo,doing so i needed to use a 300zx maf.i dump bov to atmospere and the car stalls everytime and the fix was recirculating bov but now i have no bov sound at all,i was wondering if i purchase a dual port bov and recirculate AND dunp to atmoshpere if this is best of both worlds or em i stuck forever recirculated because the sensitive maf? i suspect this is why they created the dual port bov?

[@TurbosmartHQ]

In theory switching to the Dual Port would give you the "best of both worlds." Some cars are more sensitive than others when it comes to partially venting pressure but it will certainly allow the car to operate somewhat normally.

[@bARTUUN]

I have a Turbosmart Dual Port for my Mazdaspeed3, but it's different. Body has only 1 big sealing o-ring and brass piston have 2 o-rings in the piston's body and 1 in the base. It's an old design Turbosmart? What's the reference here to adjust harder or softer with only 1 o-ring in the bov body?

[@TurbosmartHQ]

Oh mate, sorry to break it to you but you purchased a counterfeit. Our Piston Bore does not have any o-rings.

[@warbird3608]

If I want to make my Mustang ecoboost flutter, should I loosen or tighten it to make it flutter

[@Han-yy2tc]

tighten

[@ryanmcgaw7019]

Can i install one of these on my kia rio gt-line turbo ? Its a dual clutch transmission. Wondering if it will work or not. Thanks

[@andrest2002]

You can install a blowoff valve on pretty much turbo car. I would do some research on blowoff valves to fit your specific vehicle. If it comes with a diverter valve from the factory chances are there is a turbosmart blowoff valve available l

[@caycebennett8667]

Curious how y’all are routing your reclaim air. Just straight into the intake manifold? (Cent. Supercharged 3.8 Gen Coupe).

[@TurbosmartHQ]

The pressure is either recirculated to the intake system prior to the compressor (Supercharger) or vented to the atmosphere if you are tuned for that.

[@caycebennett8667]

@@TurbosmartHQ that part I understand. So if I hook up the reclaim to my intake manifold, how would I ever know how much to twist the BOV for optimal performance?

[@TurbosmartHQ]

@@caycebennett8667 The window for optimal performance can be very wide on an application. It is very well possible that the factory setting is just fine for your vehicle and adjusting it to the hardest setting may make little to no difference. In many scenario, you just want to verify that the valve is holding shut under full load and releases pressure properly.

[@pigeonsil240sx]

@@TurbosmartHQ to verfiy should i pump air into the system like we do for boost leak testing? then make sure your not bleeding off?

[@bxbyJ603]

Will the softest setting give me that loud ppshh or does the hard setting do that? It seems as if the softest setting is the way to go but, just asking for some clarification

[@demover7]

You aren't really changing the sound of the blow off by tightening or loosening the spring you are more changing when the blow off will happen. Its important to make sure you have it at the right tension or you will either create a boost leak meaning you lose power or you create surge which doesn't vent air smoothly when it needs to smacking it into the turbo which is bad for it.

[@fgtrhwu2]

@@demover7 Really? I thought if you make into a diverter valve it will reduce the sound as less air is being vented

[@demover7]

@@fgtrhwu2 Well there is a difference between a diverter and blow off valve. A blow off valve vents compressed air to atmosphere while the diverter valve takes that same air and recirculates it back into the intake. The question i was answering was weather or not soft vs hard setting on the blow off will cause the pshhh sound. When it vents it vents. It will have basically the same sound no matter what.

[@fgtrhwu2]

@@demover7 My bad I thought this was a hybrid and the soft/hard setting was for the purpose of switching between the two

[@TurbosmartHQ]

@@fgtrhwu2 Our Dual Ports will always vent 50/50 to the atmosphere and recirculate. You cannot change that ratio.

[@MAZAGAMING666]

I have a race port valve , do you know why sometimes sounds the valve and sometimes not ? I have a Procharger making 14psi .

[@TurbosmartHQ]

We have a specific version of the Race Port that has a very soft spring inside specifically for supercharged applications. Make sure you have this version. It should hang open at idle and close under boost. Feel free to reach out to us for in depth assistance! www.turbosmart.com/contact-us

[@tardis4125]

Good video, but how do you know if you need to adjust it. How do you know if your car needs it to be adjusted softer or harder?

[@weduhpeople8504]

If too soft a setting you motor tends to stall and turn off. I tighten it till it stops stalling.

[@tardis4125]

@@weduhpeople8504I'm pretty sure a blow off valve should not be making your vehicle stall

[@gainzorzilla8999]

@@tardis4125 if your spring tension is too soft the piston in the bov will not close in time before idle which will cause your car to drop below idle rpms and even stall. Basically if the spring setting is too soft you absolutely can have a car stall from a bov. At idle the car runs off a closed circulating system, so the bov piston needs to be closed before reaching idle rpms

[@tardis4125]

@@gainzorzilla8999 I'm no expert, it's just that I had my pipes for my intercooler come off and the car worked fine, just lost the power from the turbo. That's the only reason why I would think that

[@JaffaDesignsIt]

@@tardis4125 yeah but you can’t of been running a MAF right? Must of had an MAP sensor or something? If that happened to a car with a MAF sensor or equivalent it would stall because it’s losing metered air.

[@fahmiariffin2352]

I have these on my w117 cla180 amgline 2017. Im no expert about cars. this is my first car though. Does anyone know why is my BOV not working? I bought the correct model etc. Had them installed and tuned my car too. 1 month later, my dashboard engine light came up. After having it checked, i had to removed them and the dashboard engine light went off. Can someone advice me, is it because the engine is is not compatible using BOV, instead, only can use diverter valve? Some says that BOV makes my car lose power too. Right now im not using bov or diverter valve. find it wasted not to use what i already bought. But i dont mind if i need to use only diverter valve. As long as i get the correct advise to follow.

[@TurbosmartHQ]

It is difficult to say what the cause could be without know all the details. Please use our "Contact Us" form for assistance from our Technical Support team for your region. www.turbosmart.com/contact-us

[@Coasty_Kai]

Do you sell whistler trumpets cant find one for a kompact 50/50

[@TurbosmartHQ]

If its a standard Kompact Dual Port BOV then the part number will be TS-0203-3004. This does not apply to Kompact EM valves. www.turbosmart.com/product/kompact-bov-replacement-trumpet/

[@ZacharyCato20]

What happens if you do end up Tightening it to much

[@ChrisSmallman1981]

It gets really hard to tighten, then very easy

[@irvingvelasquez]

I just installed my blow off and something started to sound in the distribution of my ford f150 and the truck has 10 thousand miles Has anyone else had that happen to them?

[@TurbosmartHQ]

Feel free to contact us if you have any questions www.turbosmart.com/contact-us We are happy to help!

[@NotAndrew02]

Can you please do one for the civic si valve?

[@pitbikeadventures2872]

Civic si aren’t boosted stock

[@xavierauclairfan267]

@@pitbikeadventures2872 new model are boosted

[@chansaechao79]

@@pitbikeadventures2872 2016 and above EX, SI and Type R are turbo

[@TurbosmartHQ]

For the Civic Si (1.5T) we have TS-0203-1018.

[@marcorivas7198]

@@TurbosmartHQ can you post video on adjusting it