It works as tested but in my case when one of the modems is not connected failover does not occur. In your example you disconnect the cable to the router. What happens if instead you disconnect the cable between the wall and the modem? Leave the cable between the modem and the router in. In my case I am having a problem where I have two internet connections. Load balancing works. But when one link goes down nothing works. If I unplug one link it works. But if they stay plugged in and the internet is not working the failover does not work. I have a protocol sticky because otherwise my bank website won’t let me log in.
@FloofyTanker3 жыл бұрын
@@RCdiy So if you unplug one of the modems from your multi-wan router the failover works but if one of the WANs loses internet connection the failover doesn't work? It's not redirecting the traffic to the WAN with the working internet connection? I find that very odd, did you try tinkering with the settings?
@rgd25763 жыл бұрын
Thats what i wanted to know he should not remove the lan cable in real world it should be red light or los.
@rgd25763 жыл бұрын
He should remove the fiber cable not the lan cable for accurate result.
@FloofyTanker3 жыл бұрын
@@rgd2576 Yeah, removing the cable at the modem's end should make emulating losing an internet connection while being connected to 2 WANs more accurate because removing the LAN cable directly would just result in the multi-wan router thining that there isn't any cable attached so it just redirects traffic to where there is a cable attached.
@ReneKubicka2 ай бұрын
Thanks for finding time for this. Would you know, if the backup WAN connection is used even if the primary WAN is available and working? I ask because as a backup WAN i plan to use metered mobile connection. I do not want to use it if not necessary.
@thilehoffer3 жыл бұрын
Does this really use load balancing so both of your connections will be used or does it use one connection and then the other is a "back up"?
@michaeltorres61092 ай бұрын
he forgot to show it and try a Speedtest with 2 ISP is UP so we can see if load balancing and fail over is working
@jopex093 жыл бұрын
This is a kickass video, i have been searching the internet all over, until i found this channel. BIG KIDDOS TO KUYA TOROGI!
@jamzky60366 ай бұрын
Hello, I appreciate your content. I have a question about this device. Can it operate both WANs at the simultaneously, or does it only support an Active-Passive configuration?
@allenperera61583 ай бұрын
Does using the wizard wipe out the previous settings? or will it just add on the failover?
@michaeltorres61092 ай бұрын
Thanks for the guide but I think forgot to show it and try a Speedtest with 2 ISP is UP so we can see if load balancing and fail over is working . It is like an Tp-Link OMADA ER605 VPN router with delay or timeout when 1 ISP is down.
@KhanSharief4 жыл бұрын
which is better this edge router or mikrotik with dual fail over and loadbalance?
@aldrinpaulo28 Жыл бұрын
Sir those 2 isp can combine speed? Ex. 1st isp 50mbps 2nd 50mbps In speed test will it combine? Thank you!
@KFMEDIA254Күн бұрын
hello, i have a router which i have installed an open soure router firmware know as Gargoyle. can you help by making a video on how to set it to have dual WAN
@rrosas4 жыл бұрын
Thanks for your video! I noticed you used the Edgerouter Lite 3. What would be the difference with the ER-X for Dual WAN Failover? I have ISP 1 with a 350Mbps service and ISP 2 with 50Mbps service. Thanks!
@Gizmo19693 жыл бұрын
@TorogiPro Thanks for video I was looking before I buy, one question, when the failover activates and you are using the second connection, which in my case will be a standby 4g connection, can the router be setup so that when internet returns to the primary connection when it comes back online?
@DLSauron2 жыл бұрын
Thank you very much. I needed to change my edgerouters IP!!! Up and running. Thank you!
@JOEJOETHEJOEY4 жыл бұрын
Thank you so much!! Great video! This is exactly what I needed to find out if the Edge Router Lite can do. I have one question, I have set up quite a few "port forwards" for remote access support from some of our providers. Will I be able to keep the same ports forwarded to all the same systems within the network using the same IP's? Keep it up!
@TubolMotoadventures Жыл бұрын
Is this router checking the wan ports physical connection only or the actual internet data connectivity?
@MikePowlas2 жыл бұрын
1. If you do a (what is my IP search) Does it always use the same WAN? 2. If you have two WANS that are 10Mbps Download will it put them as one and give you close to 20Mbps Download? Thanks.
@OfirHadad4 жыл бұрын
Hi @Torogi Do you know if this dual wan router can switch to the fastest network? between the 2?
@FloofyTanker3 жыл бұрын
So you connected 2 modems to 1 Multi-WAN router, which one is the main DHCP server or assigns a dynamic IP? Is it the 2 modems? or is it the multi-wan router? I'm planning on 2 WANs and a Multi-wan router and a Switch, all the computers will be connected to the switch, so let's say I follow your steps and in your case since you assigned 192.168.100 as your routing prefix for your LAN port and I'm going to stick a switch on that end will the addresses on that switch be ranging from 192.168.100.0-255? I'm planning on setting up a multi-wan network in my home because of intermittent internet but I do not have any background in networking whatsoever other than reading through articles and watching youtube tutorials on the internet.
@joaquinluceromusic3 жыл бұрын
i am just curious if you used real 2 ISPs or just created lab vlans to simulate 2 WAN ISPs?
@myniemoo45094 жыл бұрын
I configured an edge router lite, followed the same procedure in the video using 2 ISP connection. After the configuration the LAN port was sending out internet connection. However, one of the ISP was down so, even with one of the ISP connected, LAN was still sending internet connection, however, the following day the internet connection was down and the LAN is no longer sending internet connection. Do I have to set DNS in the LAN configuration, or is it because one of the ISP connection is down to cost no internet connection?
@kaleemhere Жыл бұрын
Thank you Brother for the nice video and easily explained, i'm going to configure it in the Call Center Office today as i'm doing all the networking work there. One Question Can the Primary Line or the Secondary Line come UP immediately without any DROPS in the connection. As this is the Load Balancing Router it should switch immediately in fraction of seconds
@lordcatpotato2 ай бұрын
sir can you combine lan intranet (no internet) and another lan (with internet)
@giuseppecirchettaph3 жыл бұрын
Hello, thanks for the video. I was expecting a faster re-routing of the traffic from one network to the other. For streaming purposes (e.g. Google Nest speakers) this kind of switching from one ISP to the other is kind of slow and streaming gets stuck.
@AhmedMohamed-gy2ri3 жыл бұрын
Straightforward instructions..thank you so much. Just what I wanted these for now days virtual events.
@marito158 Жыл бұрын
thanks for the video, currently my ERL router is already configure eth0=current ISP, eth1=Lan, it has policies and rules, and couple vLans, if I use the wizard Load Balancing Config, would that erase all my policies, rules and vLans? I'm trying to get a second ISP as backup reason why I'm thinking on load balancing using the eth3, but I would not want to erase all the current setting and having to reconfigure again. thanks in advance for your advise.
@kennethdale98622 жыл бұрын
Awesome. Just maybe the solution that I need. Sir, after that config, can I plugor use a wifi router in that eth0 or confirgured lan port? Going to my existing home wifi setup?
@kinghade153 жыл бұрын
We have 2 ISP and almost 200 computers, I wonder if I can filter computers who should have access to the internet using this router or should I go purchase pfsense routers?
@thibautnoah25993 жыл бұрын
Looking good for the price. Wondering if it isn't limiting though as it is only a gigabit connection routeur. Does it work well with a switch? Want to use this as failover
@leodanterustia41164 жыл бұрын
We can actually config the delay and interval timeouts in cli.. Or config tree.. Mine is set to 1 timeout only. No timeout if 3 isp.. Cache also can be setups.. The weight per isp can also config.. Etc. Edgerouter is a powerful piece of gadget..
@torogipro4 жыл бұрын
Thanks for the info bro.
@sTIc7264 жыл бұрын
Using load balance if 1 ISP goes down the connection will also shutdown for a moment or will continue to work normally through the other ISP?
@fastbytedigitalprinting5843 жыл бұрын
What if isp 1 does not work properly? Is the isp 2 automatically fail over even not pulling out the cable connected to ER from isp1?
@AlarmSystemStore3 жыл бұрын
So when you setup load balancing, you automatically get wan failover?
@ronilhassanwalia4 жыл бұрын
Can you force a client device to only use one of the two WAN ports. For Example our IPTV Service only works on one WAN Connection. Can I force the FireTV's to use that WAN based on MAC?
@andrewkatz38453 жыл бұрын
Did you find the answer to this? I'm looking for the same thing.
@JoeCubicle2 жыл бұрын
My buddy just got a whiz-bang dual WAN router with bells/whistles so I thought I'd watch a dual WAN video. I still don't get router magic and IP addresses and all that. I simply don't get it. Great video though!
@ceekay16763 жыл бұрын
Hi Torogi! Nice Video! I have a question though, it seems that the video only shows the failover but how about the load balancing? If i connected 2 ISP on WAN ports, would it improved the upload and download speed of the connection?
@samuelg352 жыл бұрын
My question also
@aldrinpaulo28 Жыл бұрын
Any update for this query ?
@scmoseman Жыл бұрын
I guess the LAN is on a double NAT. Is there any way to port forward?
@SimowLabrim2 жыл бұрын
dude why the ping went over 100ms when you plugged both of them? this is not meant to lower the ping for video games? another question, are those lan 1 + lan 2 you plugged are a normal lan coming from different ISP routers?
@MrBassinhuntin2 жыл бұрын
Thanks easy to understand and I’m good to go.
@nomdeplume76714 жыл бұрын
exactly what i wanted to see. thank you.
@ceasbesa37673 жыл бұрын
Awesome video! Very helpful. This is what we need in the office. Just in case i get somw stumblimg blocks in setting up, can i reach out to you? Thanks.
@pembencifanatism63352 жыл бұрын
Hi Torogi Pro, Can you show me how to set Dual WAN + Failover for connection using pppoe from ISP. The ISP also set VLAN 500 and DHCPv6 /48 for that pppoe Really glad if you can show it.
@joenellagz27 Жыл бұрын
Sir may sarili din po ba na Public IP ung router?
@jassonmagallanes96074 жыл бұрын
Question, mag stack po ba ang bandwidths ng dalawang isp if both connected na? Eg; wan1@ 15mbps + wan2@10mbps = 25mbps na yung net speed mo??
@roy57213 жыл бұрын
No
@markarca63604 жыл бұрын
I would assume that this also applies to other models of the EdgeRouter like the EdgeRouter X or EdgeRouter X SFP since they have the same firmware. The number of ports is just the difference.
@manoloencelan32374 жыл бұрын
hi is it normal to take more than 10 second to do the failover? should it be 1 to 2 sec only? it would be disaster if this will be use on critical network... thanks
@torogipro4 жыл бұрын
You can adjust the time out via the terminal
@88eleaffar2 жыл бұрын
Hi, i have edgerouter x with firmware 2.09. I use wan 1 and wan 2. Wan 2 is starlink. Normal speed in wan 2 is 200mbit of download and 20 of upload. With my ubiquiti router the speed came limited to 60/70 mbit in download, why ? I have enabled/disabled ipsec and hwnat but the problem is always the same. Thanks a lot for the help.
@rgd25763 жыл бұрын
may i asked if loadbalance and failover work without removing lan cable?
@emannaval65293 жыл бұрын
Yan din hinhanap ko
@dithopulungan26873 жыл бұрын
Hi does the isp has to be the same company? Or can be different companies?
@ceekay16763 жыл бұрын
you can use 2 different ISP as you can see on the video, 2 WAN ports have different IP address. Also when he did the tracert, you can tell it that the HOPS goes into two different ISP
@jopex093 жыл бұрын
IDOL, Question po may port forwarding din po kaya jan sa edge router? Or need pa po ng another firewall pa po for it? Also if mag port forwarding ako need ko pa po ba i defined un both sa ISP modem? or hindi na po? Thank you po
@kuyavenzinfovlog4 жыл бұрын
this edge router can handle two router like from edge to hub to router1 for shop and router 2 for wireless fo4 piso wifi?
@stracomesys3 жыл бұрын
Very thorough
@abrahamtan10934 жыл бұрын
does it affect internal lan transfers? like from nas to comp?
@jt4pt4 жыл бұрын
What is the possible way to reduce latency between switchover of ISP if one goes down.
@mitchaustralia93274 жыл бұрын
Have you tried combining 2 ISP line connections to get max speed?
@pcenthusiast92114 жыл бұрын
in failover when one ISP down, the ping should be continue,it should switch over to 2nd ISP without any delay,that is the concept of failover and load balancing, please correct me of i am wrong.
@torogipro4 жыл бұрын
There will always be a delay bro, however, you can tweak some of the settings on CLI to lower the timeout as mentioned by @LeoDante down at the comments below.
@antonylmj4 жыл бұрын
@@torogipro Is there any possibility for seamless reliable internet for situations like Skype calls? I understand that failover will have a minimum delay, but in "load balancing mode" if one of the ISPs / WAN goes off, does the router ensure reliability, by not loosing any packets that may cause disruptions to Skype calls etc
@randz92394 жыл бұрын
does it need to be same bandwidth??
@jgutierrez1574 жыл бұрын
Great video. Do I need to have my two ISP Modems in bridge mode in order to get this Dual WAN Router working?
@torogipro4 жыл бұрын
It does need ti be modems in brigde mode, however it is good if do setup in brigde mode. This is as long as you to ISP sources
@abuxxx36072 жыл бұрын
@@torogipro what? english is in danger here.
@mezmerizz4 жыл бұрын
what if both my WAN modems have the same IP address because they are routers as well and have DHCP turned on.. will the Edge Router just use it anyway and not care?
@ceekay16763 жыл бұрын
as he clearly said, you need to have two different IP as there would be an DHCP IP conflict!!!!!! Also, you cannot use Router as they are DHCP unless that router's DHCP could be turned off and just use it as a modem or a bridge. But there will also issues with double NAT. Please review your basic networking
@punishedproduct2 жыл бұрын
Thank you!
@gabrielfuentes46514 жыл бұрын
Sir good day is it ok to set up this without buying a static IP from the ISP ?
@torogipro4 жыл бұрын
Yes bro.
@gabrielfuentes46514 жыл бұрын
@@torogipro thank sir another question im using a pfsense in my office is it also applicable to load balance in pfsense without buying a static IP from ISP?
@kuyavenzinfovlog4 жыл бұрын
just to clarify no ip value from eth0 kc si pfsence na ang magbigay ip tpos c edge router purpose is failover lang. is it correct?
@jeffreymagallanes14554 жыл бұрын
@@kuyavenzinfovlog may features din si pfsense ng load balance and fail over mas ok padin kaya gumamit ng edgemax?
@jeffreymagallanes14554 жыл бұрын
ano mas ok, pfsense load balance fail over or yan sa edgemax bro? Thank you :)
@sugandhpandey73684 жыл бұрын
Output lan port is gigabit 100/1000?
@waldenlaab42853 жыл бұрын
Sir what will happened when two isp dhcp meet in load banlancer ? And meet static and dhcp in load banlancer?
@edmondromanos92563 жыл бұрын
mag add ba ang speed using this router? i have 100mb pldt residential and 200mb pldt SME,, magiging 300mb kaya?
@richardsabino91903 жыл бұрын
Yun nga po sir Dapat sabay sila mag work At walang speed test Kung sabay sila Mag work?
@itmikoyito9754 жыл бұрын
sir is this device support load bonding, or do you have any idea of a device support load bonding and failover at thesame time? thanks a lot.
@torogipro4 жыл бұрын
Loadbonding? Or peering?
@itmikoyito9754 жыл бұрын
@@torogipro Loadbonding sir I don't know sir if it is peering also :-), like if we want to bond/combine speed of our two ISP's, ISP1(20mbps)+ISP2(20mbps) = 40mbps download speed
@jmarkesc68404 жыл бұрын
Try PFsense
@lemmoraguila24 күн бұрын
@@itmikoyito975 ruijie eg does this job
@ИзвестныйАпрасад3 жыл бұрын
Same way we have to configure tp link load balancing sharing switch?
@bastiaanw35193 жыл бұрын
Yeah, this works like a charm. But now... how do I configure the routers on the internet side and the EdgeRouter to pass through traffic to servers on the inside, BEHIND the EdgeRouter?
@joaquinluceromusic3 жыл бұрын
about 15 to 20 seconds. is there a way to reduce that to less than 10 mins?
@kuyavenzinfovlog4 жыл бұрын
can we combined the network for us to avoid request time out once one of the isp having data congestion?
@torogipro4 жыл бұрын
Yes amigo. Thats where load balancing works.
@ibclay14334 жыл бұрын
Fantastic video! Sir, any comments of connecting an Orbi mesh router/wifi to an Edge Router for load balancing purposes? Thank you
@mykilbee3 жыл бұрын
is there a way to get failover a little faster, that was fifteen seconds, in the gaming world that is like a day and a half?
@odelts4 жыл бұрын
this is like 25k to 30k pc of equipment bro, right? you got voucher?
@torogipro4 жыл бұрын
this is around 7k bro
@vinothyuvarajan98872 жыл бұрын
How to bond both wan connection ?
@TatayOpaw3 жыл бұрын
new subscriber! nice content.
@heartgalgao42384 жыл бұрын
okay I found the price. for the price not bad.
@JoeM37010 ай бұрын
The clarity and insight of this content are refreshing. A book with related subjects expanded my understanding. "A Life Unplugged: Reclaiming Reality in a Digital Age" by Theodore Blaze
@abuxxx36072 жыл бұрын
7:39, it is a failed test. no way in real life scenario that removing a lan cable will simulate a down isp. there should be parameters meet before the failover happens.
@kuyavenzinfovlog4 жыл бұрын
if in case there's a second no internet during switching of isp, based of my understanding
@focuslinkstech4 жыл бұрын
this video is informative, but you dont do speed test on both internet for load ballance
@micoryanelgana67474 жыл бұрын
Salamat idol .. dami ko natutunan sau :) more video pa idol .. and pahingi facebook page mo idol para ma followed kita
@POSITIVEPULSE0154 жыл бұрын
Mas ok pala to sir? Kisa sa microtek
@torogipro4 жыл бұрын
Oo, straight forward kasi ung features. Si mikrotik, sa dami ng pwede nia gawin, magugulohan ka hehe.
@itmikoyito9754 жыл бұрын
@@torogipro yeah i tried to do it in mikrotik haplite, its working but not that kind of autofailover when 1 connection fail.
@POSITIVEPULSE0154 жыл бұрын
@@torogipro sir totoo ka talaga.. salamt solir
@heartgalgao42384 жыл бұрын
how much is the device?
@torogipro4 жыл бұрын
7k madam
@akiraG244 жыл бұрын
Supported ba nyan Sir ang VLANs?
@torogipro4 жыл бұрын
Yes bro
@hereravera35913 жыл бұрын
2 isp 100Mbps+50 Mbps=150 Mbps??
@rcttechnical11704 жыл бұрын
Request on pppoe server configuration using mikrotik, on ptp wisp, with tree connected lap 120 sector anten for example tnx
@torogipro4 жыл бұрын
cge list ko sa upcoming tuts. Thanks!
@stephentsilo48133 жыл бұрын
Good video but fail over takes some 20seconds to forward traffic is there a way of minimizing the time...if i was on a voice call...its gone!! man.
@pcenthusiast92114 жыл бұрын
request you to make video on WOL Wake on LAN
@micoryanelgana67474 жыл бұрын
Ma total poba internet mo dito boss Globe 50mbps / pldt 50mbps = 100 mbps ?
@jokeng10354 жыл бұрын
that's what I want to know too.
@yashbhikadiya5404 жыл бұрын
Bro,please make viadoe on how to disable hot key in windows. I failed in all try of all youtubers.
@PeterParker-mz7fk4 жыл бұрын
I thought it will just be smooth.
@wfhxsahgf4 жыл бұрын
Urgh. Ang hirap ng hindi techie. 😭 ang dami ko na pinanood na ganito nahihirapan ako intindihin. 😭 Helllppp. 😭 meron bang device na pwede ko iconnect via ethernet port ng laptop yung 2 ISPs ko ng walang madaming technicalities. Like kung paano nagwowork extension ng phone. Huhu. Please help me. 😭
@jhune07314 жыл бұрын
Load balancing router plug n play nayan lagay molang 2 isps mo then ung out nun naka merge na ung data bandwidth. Kung sa laptop naman working din ung pldt naka wifi then converge naman naka lan working sa win 10 ko yan
@wfhxsahgf4 жыл бұрын
Floro Compe jr. hello! Thank you sa help. Bali ang gamit ko pldt fiber na laging pumapalya and globe dsl. Pwede po ba yun na dsl and fiber ang ilalagay? Thank you so much! Hindi ko ineexpect na may magrereply sa comment ko. Hulog ka ng langit sir!
@peras123453 жыл бұрын
Its not fail over , its a load balancing
@markarca63604 жыл бұрын
EdgeOS is based in Debian so you can use the APT repository the same way you use it in desktop versions of Debian, Ubuntu, and Kali Linux.
@Theonecalledmom Жыл бұрын
I need to set up Internet service for my 5th wheel travel trailer. I need to have multiple providers, so not to loose connection when I am at work. I have to have 12mbps, per my IT guys🫣