UltraFresh Front Load: How to Change the Washer Door Swing

A step by step walk through on how to properly reverse the door on the GE Ultra-Fresh Front Load washers.
GFW850SPNRS, GFW850SPNDG, GFW850SSNWW, GFW650SPNSN, GFW650SSNWW, GFW550SPNDG, GFW550SSNWW, GFD85ESPNRS, GFD85ESPNDG GFD85ESSNWW, GFD65ESPNSN, GFD65ESSNWW, GFD55ESPNDG, GFD55ESSNWW

[@sarah.fb.lindsay]

Success!!! I didn’t have a lock bar tool so I just held onto it. Didn’t have any issues. Great tutorial.

[@StockDude]

Thanks for the clear concise instructions. I got this done with NO issues. I don't know what some people down in comments are referring to about wiring problems and getting door error messages. There should be no issues with this at all. I did each segment as I watched the video and paused the video between each step. EASY!

[@erikagibson]

This video helped me do this by myself because my husband didn’t want to!!! You Rock because I did it and he was impressed!!

[@avigail9951]

Now get rid of the husband

[@Saturday8pm]

Success! I skipped using The Lock Bar despite getting one quickly from GE. If you don’t know about it and want to reverse the door later, you won’t find it because the installer will haul it away upon delivery. Before indulging, I checked uniformity with all fasteners. They checked. The only problem I encountered was how fast tight the wire connectors were. Not easy to pull, I used pliers which nearly broke one. Once everything was tight, I started a small load. Yep, the lock buzzer sounded, so I hit Pause then Start. Nope. I turned the washer Off and repeated. This time the door locked as usual. The best part? NO LEAKS. Now I have BOTH units swinging open in the way we planned. One Thing: I suspect reversing doors on washers is best done when the purchase is fresh; wait, and the gasket may not be forgiving. Thanks for the vid.

[@kristakat]

I’ve had my set a couple years and it worked perfectly. I didn’t have the lock bar either but did it just fine

[@michaelradmer9480]

Hi -- did you use a tool to hold the mechanism or just fingers?

[@DanLivingston]

If the lock bar tool doesn't remove easily, take it back out and look on the bottom right of the unit. There is a pin that should be in the recessed position. I had take mine back out, push that pin back into place and the bar removed easily. That warning should be added to the instruction video.

[@geappliances]

Thank you for sharing this, Dan. We will pass this along to the video team. We appreciate the feedback. Sincerely, RF

[@gordonshumway5653]

This was super helpful. Thank you for taking the time to share.

[@geappliances]

We are glad you were able to find value in this video, Gordon! - TS

[@lkinerk]

Thank you thank you thank you. That part had me stumped.

[@jerrytroiano92]

Yeah, the instructions didn’t mention this pin, and I pulled it like in the video. Now the bottom of that piece is cracked.

[@jennifera426]

Door Lock Bar Got Stuck! I had the same issue that alot of you had with the lock bar getting stuck. Ours ended up breaking off inside and after hours and hours of prying we were finally able to get the plastic piece out. However I think me mangled the mechanism inside and the door wouldnt close properly after. This was a brand new machine that we had just gotten 2 weeks prior, so I called GE customer service who put my service request through to a local service center. When I didn't receive a call from the local service center I called them myself only to be told that it would be atleast 2 months before someone could come service my machine. Not only that, but by the time they come to take a look at it they would still have to order in the part and then schedule another service call. I found the part online (door lock) and purchased it (cost almost $100), after 2 weeks it came in and we installed it on our machine (works great now). I am upset because we followed the instructions to a "T" and all it says is to pull out the lock bar. I am hoping GE will reach out and come good for the cost of this part; there is no way I could have been without my washer for months until service could arrive. GE please update your instructions to save others from this situation happening to them!

[@DanLivingston]

I posted about this issue 2 years ago. GE won't update the video with correct instructions.

[@gcmperalta]

I completed this on a new UltraFresh Washer. There is no part in this process that goes as smoothly as the video except for screw removal. One main problem is aligning parts on their new location. Some of the plastic doesn't align perfectly until you make numerous micro adjustments. Some of the new screw locations have not had screws in them prior and it is hard to get the screw all the way in at first. I used the lock bar to remove the terminal block but only half inserted when I could due to the scary comments here about breaking parts. Putting the door back on is very difficult even with the hook to hold it. The screws do not line up until many small adjustments are made while trying to jockey a heavy and awkward door.. The wires only plug back in in one way like someone mentioned so this is one less thing to go wrong, Glad it is over. Dryer waits for another day., ,

[@geappliances]

We're sorry to hear about the difficulty you had during this process. We recommend reviewing the instructions for your specific model in the Installation Instructions written for your model. You can find these instructions here when you input the model number: spklr.io/6055sANh

[@gcmperalta]

@@geappliances Your comment misses the mark. I had plenty of written and video instruction. Many nuances are not covered in either,

[@geappliances]

We appreciate your feedback and will be sure to share this with our engineering and design teams. We apologize again for your inconvenience.

[@whatsthisnow]

For anyone getting the 'Door" error after reversing make sure you flip the wires on the side you are moving it to. I went through removing and re-attaching the door and all associated hardware probably 2 or 3 times and kept getting that door error before finally realizing that the sensor on the opposite side was wired brown on top red on bottom and my side was red on top brown on bottom. Flipping the wire on the side I was moving it to did the trick. Why on god's green earth they couldnt have just wired both sensors in the same direction is beyond me. Or at a minimum call this out in the directions at LEAST. Strike one GE!

[@troyalton4956]

Justin, you just saved a repair call for me. Flipped the plug around and its working perfectly. Thank you!

[@deek49]

I switched my door today, and was ready to heed your words due to your comment, but GE may have already heard what you and others have said and switched the design as when I got to that part there was only one way the wires would plug in. Finished assembling, ran the machine, and all is well. :)

[@samueltarasewicz2514]

You’re a lifesaver!

[@Caleb-hx4cd]

I had no problem doing this without the lock bar. I just used my hands, and made sure i didnt let it fall inside the unit.

[@nospam276]

A number of people in the comments have mentioned their Lockbar getting stuck. I just did mine tonight, used the Lockbar, and pulled it out no problem by pulling straight back, as in the video. I will note, I played the video at 25% speed at that part, to make sure I was inserting the Lockbar right-side up and not upside down. I probably played that part back three times @ 25% speed, and in full screen. There were a couple other spots where I had to go 25% speed and repeat a few times. I often wanted to see the exact way they pushed or pulled something. Definitely made the job easier. The only thing I found incorrect in the video, is where it mentions to not tighten the screws on the striker. The GE manual does not mention this, and I found that it's (nearly) impossible to tighten them to a point where the striker plate won't move. When you tighten them all the way down, the striker plate is still designed to slide around. I at first left them pretty loose, per the video, but I could just imagine them jiggling free one day and falling out, with washer chaos to follow. Tighten them down and just make sure the striker still has some play to move left/right.

[@benc4181]

A video for the dryer would complete this video

[@gregthomas-pu7lc]

Thanks Dan! I'm a pretty mechanical guy but I was just about to cut this tool outta there...thankfully this comment came up first!!

[@tonysolis8199]

You should do a video on how to reverse the door on the dryer also.

[@shelbyralynn9167]

Welp I did not read the comments before trying to pull the stuck lock bar out. Now it is broken inside the lock and I can’t seem to get it to unlock no matter what I do. Would have been a very helpful to mention in the video about having issues with the lock bar being stuck.

[@stevenosvold2040]

You should really update the part about the lock bar. Having seen so many people with the issue, it almost seems you want it to break so that you can get more money from them.

[@wilsonjohnson9774]

Great video, very informative, but there's about 500 different Phillips screwdriver.Thanks again for the video👍

[@geappliances]

We are so happy to hear the video helped! We appreciate your feedback and will be sure to share it with our teams. If you don't already own a "Phillips" screwdriver, the size you're most likely to need is #2. If you have any questions in the future, please let us know. Thank you! JW

[@gordonshumway5653]

Dear GE, thank you for making a front-load washer with a reversible door, and for providing this video. I do have a question, however. The washer is easily reversed using only the lock bar and a phillips screw driver. Why make the dryer use 2 torx screws, 2 nut screws, and the rest phillips? Would be nice to keep everything consistent, especially when the dryer doors are reversed much more often than washers. Just a thought from someone working for a self-servicing GE dealer. Would help out my warehouse personnel.

[@geappliances]

Hi Gordon - Thank you for your feedback. Your comments are important to us. Our product design division takes these suggestions into account when planning future products. - TS

[@Codenames560]

hey Gordon, your suggestion might worked. I just reversed the opening door today and all the screws were philips. :)

[@ThuanDotLink]

@@geappliances Wow! GE is actually reading comment on KZbin.

[@yegwanihst1971]

@@geappliances can I use pliers in place of my lock bar?

[@colinryan4069]

Unable to close door after switching sides, feels like there is something in the way (and visibly can see a white plastic piece that would block the metal part from completely going in the locking mechanism on the unit.

[@handsonthroat]

Thank you so very much! It was like you were right next to me, telling me what to do in order. Bless y'all! ♥️

[@geappliances]

We're so glad this helped you!! We're always here if you need anything. Have a nice day. -SH

[@westont5039]

Great step by step instructions!

[@yegwanihst1971]

@GE Appliances can I use pliers in place of my lock bar?

[@wisheduknew294]

Yeah I did mine and the part that latches the door with the spring mechanism in it broke had to spend nearly $50 to order another one

[@jasonjtg21]

Worked perfectly thank you.

[@geappliances]

Glad to know that we were able to help! Please feel free to reach out to us in case of further assistance. Sincerely-DM

[@Bulldog75stp]

My lock bar broke inside the door latch. I called your customer support number and they said it is not covered under warranty. I haven't even washed the first article of clothing and now this thing is broke. I followed this video and even paused the video after EACH STEP! Could someone message me about this? I don't think it's right to have to pay a $100 service call on something that broke while following YOUR instructions. Thanks.

[@masonmccarthy9057]

Scam artists, all appliance brands are shit honestly, all of them are so cheaply made but sold at an insane rate.

[@N0AHVEGA]

Thank you for this video! Now I just gotta live with my washer door not being reversible 😢

[@geappliances]

We can double-check this for you can you PM us the model and serial number on your unit?

[@setdecsetdec327]

Worked 100%. Thank you

[@geappliances]

Great! Thanks so much for letting us know. We're happy to help if any other questions come up. Best, JP

[@TonyFlemingorg]

As others have noted DO NOT USE THE LOCKBAR. It will easily break off inside when you attempt to remove it. Just happened to me. When it breaks off, it damages the locking assembly and the door will not shut. Just had to buy a new assembly from GE, because they have so far refused to put a warning on the video above as several have asked here. On hold with GE Consumer Relations regarding this to ask them to refund the purchase cost.

[@geappliances]

Hello-We are sorry to hear about the trouble you have had with your unit. We do hope the situation has since been resolved. If we can help look into it further for you please feel free to send us a private message with your contact information and include your full model and serial number. All the best-DM

[@___-iw6hb]

The hinge assembly does not sit flush in the cavity where the striker assembly sat. The hinge assembly is just VERY slightly to big. I could perhaps force it, yet.... I have not yet given Costco or GE time to respond yet. Will try to come back and give an updated solution.

[@geappliances]

We'd be happy to look into this for you. Please provide the model number for your unit, so we can better assist. Instructions for locating this number can be found here: spklr.io/6056ts8G

[@adamskove]

Awesome video! Did it myself. 😀

[@geappliances]

That's what we like to hear! - TS

[@Qui666zhpe]

Make one on how to replace the gasket

[@StevenVanderVelde-tc8ff]

Just had my lock bar tool break off too. Spent an hour trying to get the piece of plastic out of the locking assembly. I got it, but the assembly must have broken from the lock bar tool as the door won’t close now. Very disappointed in GE for this video not addressing that fatal flow as others have pointed out. Same is true in the printed directions in the manual that came with the unit.

[@kristakat]

Perfect instructions!!

[@geappliances]

Hi Krista. We're so glad that these instructions were helpful! If you have any questions about your appliance, please don't hesitate to reach out. We're glad that you've chosen to be a part of the GEA family! -AT

[@jonlovins5335]

Got it done. No lock bar needed. Seems to be fine

[@richardelliott8201]

The instructions were great. But I couldn't find my lock bar. So I proceeded and switched the locking mechanism to the other side anyhow without using the lock bar. Now the locking mechanism is locked - ie. I can't close the door...any suggestions?

[@jonlovins5335]

Any solution?

[@rongainey7047]

I tried to do it then realized mine did not come with a lock tool. Spent half an hour wondering how I'm going to change the door.

[@_brovak]

Alright everyone. You don't need the lock bar tool. You just need to hold the gray part firmly when unscrewing it and screwing it back in and be very careful when tilting it out of the hole.

[@mo25ousa]

So the little white housing sensor that comes out of the left side, was I supposed to put that back in on the other side before putting the hing back on ? In the video if you pause at 2:51 the white housing peice is not in there, then when the video continues it just magically appears back in there but didn’t include that in the step, I tried to plug it in but the wiring did not want to fit. Machine is running without error code not in it curently

[@geappliances]

We recommend reviewing the steps in more detail within your unit's owner's manual. For an example, you may view washer GFW650SPNSN manual here: spklr.io/6051qCtP. -- Reversing the door starts on page 27.

[@jeffryblackmon4846]

I never received that lock bar with a new washer and a new dryer. I think the store stole them for their service techs. It cost me over $25 to buy one. When I got to the actual work, there were all sorts of problems. For one, the hinge mount would not fit flat on the washer body. I found 2 alignment pins on the back that did not line up with the holes in the washer body. Had to remove them. It was not a pleasant experience. Looking at my dryer, the hardware looks entirely different for the door. I'm not going to mess with it.

[@geappliances]

Hi, Jeffry! Congratulations on the new washer and dryer! We're sorry to hear you did not get the lock bar to reverse the door on your washer. While unexpected, should accessories be missing from a new appliance, just reach out to us in the future and we'll be happy to help! Enjoy laundry day and let us know if you have any questions. - JB

[@stevkoria]

perfect worked for me thanks

[@geappliances]

Glad to hear this worked for you! - TS

[@ronhutcherson9845]

What lock bar? I never once saw it. Did the installer throw it away? I’ll never know.

[@geappliances]

We're sorry to hear you're missing the lock bar. Were you able to properly install the unit as well as change the door swing direction, if needed? If not, please let us know.

[@charlesrizzo6996]

Watched the video, read the comments ( some of them) and I am ready to go. Can anyone tell me where I can find the bar tool? It is not in the bag with the instructions and warranty papers. Is it hidden somewhere in/on the washer? We bought these ate Lowes about 3 weeks ago.

[@gcmperalta]

The delivery people don't leave it. Had to buy one on-line

[@Berman-s8f]

How about the dryer door changing the swing.

[@daave0]

Thanks for the clear instructions!

[@dtxgmoney]

You’re welcome, David.

[@AskSamS3936]

This is also called reversing a washer door.

[@donnacendana7360]

Plastic bar lock broke!!!!! Just purchased the new washer 2 days ago! Door lock messed up :(

[@DarWehrlie]

purchased from Lowes- did not get a lock. bar-- can it be done with another type of tool? if not where do I get one?

[@geappliances]

Hi there - Please send us a private message on Instagram or Facebook with your model and serial numbers, as well as the part you're missing, so we can look into this for you. Instructions for locating your model and serial numbers can be found here: spklr.io/6057qmFF

[@cecilychristopherjanarek1979]

Hello we purchased our washer and dryer from Lowe's and did not receive a lock bar. Is there a link you can provide to purchase this tool?

[@geappliances]

Hi Cecily. We're sorry to hear that you did not receive this lock bar, we know that must be frustrating. Please fee free to reach out to us privately on either Facebook or Twitter, whichever you prefer, with your name, phone number, email address, shipping address, and the model and serial numbers of your washer and dryer. We hope to hear from you soon. -MS

[@cecilychristopherjanarek1979]

@@geappliances Thank you very much and will send a facebook message.

[@duliriel]

It is included in the owner’s manual package.

[@gcmperalta]

@@duliriel No it is not. The delivery people take it with them

[@supergary4988]

Thank you bro

[@LocalAutosOnline]

Need to remember to tighten the latch ..; )

[@leapickard]

Lol thought the same thing!

[@tonysolis8199]

Everything was great until my lock bar broke inside the connector. Took me about 30 mins to remove the plastic from the inside but other than that everything was easy.

[@geappliances]

Hello Tony, we apologize for your experience with the lock bar. Were you able to get the door swing reversed? -BL

[@tonysolis8199]

@@geappliances Yea I got it to work. Thanks

[@geappliances]

Great news, Tony! Enjoy and let us know if you have any additional questions or concerns. Sincerely -SF

[@juliejules4116]

The same thing happened to me! How did you remove the plastic?

[@juliejules4116]

@@geappliances I had this same problem. What is the best way to get the piece of plastic out?

[@pcscleansbynicole]

You guys should do a video for the dryer too!

[@geappliances]

Thank you, Nicole, for your wonderful suggestion about a video for the dryer too! Please see your use and care info. for instructions, or please let us know if you have questions. Thanks for reaching out to GE Appliances! -NC

[@dtxgmoney]

@@geappliances a video for the dryer would definitely compliment this one.

[@geappliances]

Hello Garrett. Thank you for this feedback. To reverse the dryer door it is included in the installs for the model dryer. We are adding more videos as we can . We sill forward your request to our Website team. GA

[@francelarebelle1138]

Did you make one about the dryer?

[@ks20645]

Make the dryer video

[@errolalex2608]

You don’t show in the video the adjustments of the door latch You only said leave the 2 screws loose after rotating it 180 degrees

[@alimnt]

I couldn’t find the lock bar. Where is it?

[@lace77721]

Just wanted to help everyone out that comes here with a lock bar getting stuck!!! We thought we had the same issue! It's NOT shown in the video, but all you have do is press in on grey "locking" mechanism button/bar immediately above it, & then it will "release" the lock bar! :-)

[@Saturday8pm]

Hi Lacey, Do you mean the long gray button that’s just above where one inserts the Lock Bar? Press that and the bar releases? Thanks!

[@lace77721]

@@Saturday8pm All i remember is that its in the location that would be the equivalent of the door shutting once it would be there, it would natually be pressing it in when it closes. Let me confirm this with my husband this evening & I'll let you know back! :-)

[@Saturday8pm]

@@lace77721 Thanks, Lacy. It’s confusing because at least one other comment here insists on “looking down the right side of the unit” but I think they meant the right side LATCH area specifically, as that’s where the button is, which would make a lot more sense. Yes, that button tells the machine the door is latched and MAY govern the part that locks the door and if messed with MAY grab and hold onto the Lock Bar, as the bar has on the insertion end a closed hook that could get unintentionally “locked” into place.

[@kodegyrl]

I did all the steps, the only one I am not sure about is if I tightened the striker too much. First time running it after reversing door swing I think I got a door lock error? After starting the cycle it went through the sensing step and before it started the actual washing part it stopped flashed "door lock" (where the word lock was just a picture of a lock) and just stayed that way until I paused and un-paused. After I un-paused it, I heard it click to lock. Now seems to be running fine but I am now paranoid. Is this normal or did I make a mistake? How loose is the striker supposed to be?

[@geappliances]

Hi Kodegyrl, Thanks for reaching out! The washer door will automatically lock when the unit has been started. If the washer is running, press the START/PAUSE button once it will pause the washer and unlock the door. It will take a few seconds for the door to unlock after pressing PAUSE. Press again to restart the wash cycle. In some cycles the washer will drain first, and then unlock the door when it is paused. The washer performs automatic system checks after pressing the START button. Water will flow in 45 seconds or less. The door may lock and unlock before water flows; this is normal. Do not try to force the door open when locked (LOCKED indicator ON). This could result in damage to the washer. Please feel free to send us a private message on Twitter or Facebook should you have any other questions or concerns. Stay safe. -MS

[@kodegyrl]

@@geappliances Thank you so much! I haven't had the message again so maybe I just didn't close it all the way the first time I tried it. I LOVE this set. They are so great! Any chance you will put out a video to change the swing on the dryer door?

[@geappliances]

Hi Kodegyrl. We are so glad that you love the set and it is our pleasure to help you. We have not done a video for the dryer door yet. However, we will pass this along to the laundry team. It is a good idea to have a video for that too. All the best, RF

[@StockDude]

Does the lock bar do anything besides hold up the latch so it doesn't fall in the machine?

[@geappliances]

The lock bar is a tool only used to assist you when changing the door swing on your unit.

[@StockDude]

@@geappliances , thanks for the reply. I get that it's supposed to assist me, but what does it do? They didn't give me mine when they delivered my unit this week and I need to switch the door around.

[@geappliances]

It latches on to the part so that it can be properly removed and reinstalled. We're sorry to hear you didn't receive one with your washer. Please provide your washer's model number, so we can look into this for you. Instructions for locating this number can be found here: spklr.io/6054soyQ

[@StockDude]

@@geappliances , why can't I use a pair of vise grips?

[@geappliances]

We would not recommend that. We would suggest following the install guide for the unit at the link and if reversing the door swing please use the lock bar. The part number is WH01X30057 and can be found using the link we provided below. spklr.io/6053sobv (page23) spklr.io/6054soba.

[@justshady]

DO NOT USE THE LOCK BAR! Mine got stuck and I had to open the whole assembly to release. AGAIN DO NOT USE THE LOCK BAR AS STATED IN THE VIDEO.

[@rickhernandez4775]

How do we get a lock bar? It did not come with our washer and we need to reverse the door swing....

[@geappliances]

Hi Rick, Thanks for reaching out. Sorry to hear that you didn't get a lock bar with your washer. If you can send us a PM on Facebook or a DM on Twitter with the following, we'd be happy to get one sent out: Phone number: Email address: Shipping address: Complete model and serial numbers: You can use this link if you need help locating those numbers: spklr.io/6058crHn Hope to hear from you soon. -MS

[@francelarebelle1138]

Done thanks

[@hbeissinger]

Is the matching dryer the same process?

[@geappliances]

Yes, these instructions are for the dryer too. Please let us know your model if you aren't sure. These instructions refer to the following dryers: GFD85ESPNRS, GFD85ESPNDG GFD85ESSNWW, GFD65ESPNSN, GFD65ESSNWW, GFD55ESPNDG, GFD55ESSNWW

[@sweetyliz32]

I got my washer and dryer from Home Depot we ask both door change but they didn’t do it and when we call they said they can’t do it for the washer. After having a really bad experience with the delivery guys and now this and still waiting for the plumber that they promise to send who knows when .

[@geappliances]

Good Morning Liz - Thanks for reaching out to us, and for your purchase of new GE Appliances! We truly appreciate your choice to do business with us, and are sorry for the frustrating experience you have had with the installation of your laundry products. What are the full model numbers of your washer and dryer? This will help us to best advise on reversing the door swings. If you need help locating your model and serial number, please visit: www.geappliances.com/ge/find-model-serial-number. - TS

[@sweetyliz32]

@@geappliances hello thanks for your respond the model number of the dryer is GFD65ESPN0SN my husband was able to change the washer with your video. Also I put a complaint in our local Home Depot about the awful delivery guys and awful experience we had. Hopefully you guys can do something about it is not professional what they did in our house .

[@geappliances]

Hello, Liz. Thank you for getting back to us. If you still need instructions on reversing the dryer door, it can be found on page 30 of the manual here: products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-3000206-1.pdf The new washer that matches this is one of the only washers available that is capable of reversing the door. This is a new, rare feature that we are still educating installers on and apologize for the inconvenience. Thank you for bringing this to us and let us know if you have any more questions. - JB

[@masonmccarthy9057]

Delivery guys don't want to switch the door because the dumbass lock bar always breaks

[@jimostrosky6571]

should the holes on the opposite side (which held the latch) already be threaded ? Mine are not, and I don't want to ruin the screws/door.

[@jimostrosky6571]

threaded, aka tapped.

[@jeffreyhwang9222]

@@jimostrosky6571 I just reversed the door using phillips screwdriver as I did not have a powerdrill. My bad. I could not get the screws in the new holes by hand so off came the door whilst I made sure the screws could go into the threaded holes all the way. After that, the door went back and with some effort, got the six screws in tight. Why it was off a bit, I don't know.

[@frieswiththatplease711]

Tell me why I cannot align the hooks to attach the door to the washer face? I’m at the last step and I cannot for the life of me get the hooks to stay in the holes provided!! 🤯🥵

[@geappliances]

Hello-We appreciate you reaching out to us and would like to help. Could you please private message us with your model and serial number on your washer unit, so we can look into this for you? Hope to hear from you soon. Sincerely-DM

[@esotericknives4828]

Hi GE, is it the same process for the dryer door?

[@geappliances]

Hi there! This is a great question. What is the full model number of your dryer? If you need help locating your model and serial number, please visit: www.geappliances.com/ge/find-model-serial-number . - TS

[@joshlawrence4707]

@@geappliances gfd85espn0rs

[@geappliances]

Thanks for providing that information, Josh. You can view the instructions for reversing the door on this model starting on page 30 of the installation instructions: products.geappliances.com/MarketingObjectRetrieval/Dispatcher?RequestType=PDF&Name=49-3000206-1.pdf . I hope this helps! - TS

[@joshlawrence4707]

@@geappliances looking for the video not instructions from a manual

[@geappliances]

Hi Josh. Thanks for sharing this. GE Appliances does not have a video for the reversal of the dryer door. We do not have a video for the dryer door reversal like we do for the washer. We appreciate your feedback and will provide this comment to the dryer product team. We are sorry that we do not have a video to send at this time. All the best. Sincerely, RF

[@Damonguilfoyle]

HELP! I switched to door just like the video instructed it was very simple but when i went to run it the machine beeped and the word "door" flashed across the screen. Now the machine will not work. Is there something i didn't do like reset the machine or something. I took it back apart and resecured everything, rewatched the video and at no point have I done anything different. Am i missing something?

[@patrickmcnichol6403]

I am in the same boat. did you find a solution?

[@troyalton4956]

@@patrickmcnichol6403 flip the wiring plug on the locking side.

[@ryanmorin2359]

I did that… didn’t work for me

[@xiuxiucuocsongochicago3774]

why i got door sensors everything i follow is right

[@geappliances]

Please provide a detailed description of the issue you're experiencing, as well as the model number for your unit, so we can look into this for you. Instructions for locating this number can be found here: spklr.io/6050tO40

[@Einlaw1]

We watch the video several times. When we turn the washer on it says door and now will not run the washer. We unscrewed everything checked the video we did the connections step-by-step about five times it’s still flashes door. What should we do now? We reached out to the phone number on the packing slips and I’m waiting for a callback but it has now been 48 hours

[@geappliances]

Hi there. We're sorry to hear that you're seeing DOOR on the display, we know that must be frustrating. If you've attempted to re-install the door several times, you've followed these directions carefully, and you're still seeing DOOR on your display, a service call may be needed to further investigate the issue. If you need to reach out to our service team, they can be found through the following link: www.geappliances.com/ge/service-and-support/service.htm Please let us know if you have any other questions or concerns. -MS

[@JamesJdoom]

Hi, same thing is happening to me. Did you ever figure out how to fix this?

[@patrickmcnichol6403]

@@JamesJdoom this is what is happening to me, were you able to fix?

[@patrickmcnichol6403]

were you able to resolve this?

[@zeilannisamson7763]

@@patrickmcnichol6403 Hi, I just did this today and you have to flip the wiring on the locking side where the red wire goes up and the brown wire is on the bottom

[@erican6515]

Can someone advise on where this lock bar tool is located or can be found? The installer did not leave me a lock bar for the GFW850 washer that was installed, and was not in the bag which the manual and the registration card came with.

[@troyalton4956]

It should be in that bag. the installer probably put it un his pocket by mistake.

[@geappliances]

Hi Benjamin, great suggestion and we will be glad to pass it along. We also have these details in your use and care booklet. Please let us know your model number and we can show you where this is located. If you need help in locating the model number for your appliance, the website below will help you: www.geappliances.com/finder/daughter.htm Thanks in advance for helping with the additional information.-SF

[@kenzo5197]

The video looks great. Problem I have is that a lock bar was not provided with my machine. It is shown in the owvers manual. Should this be provided with the machine? I would think so, perhaps it was an over site . . . How do I go about having one sent?

[@geappliances]

Hi Kenzo. We are very sorry to hear you did not get the lock bar with your new Ultra Fresh Front Load unit. It would be our pleasure to send you one. Just reach out to us here: www.geappliances.com/ge/service-and-support/contact.htm Thanks! - JB

[@DanLivingston]

Will you please fix this video! You are giving people bad instructions. See my comment above for the correction needed.

[@GreggShaub]

Anyone know how to fix the ultrafresh vent function? Had techs out 4 times and they replaced the fan and the control board. Still not working. The fan and the damper seem to work during solo tests but not during the vent cycle.. it's been almost a year dealing with "techs"..

[@geappliances]

Hello, Gregg. We are very sorry to hear about the trouble you have experienced with your washer and would be happy to look into it. Could you private message us on one of our social media platforms with your service confirmation number? Thanks! - JB

[@GabrielKramer-r5r]

How were any of you able to get that little white piece of plastic out of there?????

[@geappliances]

Hi Gabriel, Thanks for reaching out. If you're having issues with installation, feel free to provide more details about the hang up and we'll do the best we can to help out. -MS

[@GabrielKramer-r5r]

@@geappliances - As so many in this thread have commented, removing the lock pin from the lock mechanism/assembly has resulted in a little white piece of plastic breaking off and getting stuck inside the lock mechanism. I cannot dislodge it, and thus the door will not close rendering the entire washer useless. Now, I need to find a replacement lock assembly. If you really want to help, send me a new lock assembly. This whole experience has left a very sour taste in my mouth towards GE. I’m extremely frustrated and fed up with not being able to do laundry in my home.

[@Trd2010SpeedwayBlue]

Anyone doing this you DO NOT need the tool. Don’t buy one. I did for $12 and wish i didn’t. Easy to swap had 0 issues

[@mavinky]

Where do I get the lock bar?

[@geappliances]

Hello, Thanks for reaching out. A lock bar is supplied with select washer models. We recommend contacting our Parts Team at 1-877-959-8688 Monday - Friday: 9 a.m. - 7 p.m. ET (closed Saturday & Sunday) with the model number of your washer, and they'd be glad to help! Take care. -SH

[@ks20645]

What about the dryer

[@geappliances]

Hello. We certainly understand your interest in adjusting the dryer door, and we’re glad to assist. If you can, please send us the model number of your particular dryer, here or with a private message over our GE Appliances social media (such as Facebook or Twitter). With that information, we can certainly look into this further for you. We look forward to hearing from you again, so we can help. Best wishes! -SG

[@andrewkinslow8725]

Maybe consider making this entire process a bit less .. screwy .. huh?

[@mf8615]

Just reversed the door. No lock bar required. I don’t even have one. Just use your fingers.

[@wes11bravo]

It's just that easy.

[@ratsnest261]

@1:29 That's not right, is it?

[@geappliances]

Hello-Thank you for reaching out to us. We would like to help look into this further for you. Could you please send us a private message with your full model and serial number? Sincerely-DM

[@ratsnest261]

@@geappliances My washing machine is irrelevant in this matter. The video shows the screws being tightened before the hinge cover has been correctly placed, thus deforming the outer edge of the door.

[@geappliances]

Hello-Thank you for sharing your concern. Tightening the hinge assembly can only be done prior to the hinge cover being screwed into place. While the video shows a slight shift in the rim during this process, the outer rim will not deform. If we can answer any other questions feel free to reach out and let us know. -DM

[@jeank5254]

Thanks for ruining my BRAND NEW washer I received today! Didn't even get ONE load washed! Please, please PLEASE update your video/instructions to warn about the lock bar tool getting stuck!! 😡🤬😡

[@geappliances]

Hi Jean, Thanks for reaching out. So sorry to hear about the issues you've encountered here with your new washer, we're sure this would be frustrating and disappointing to say the least. If you're unable to remove the lock bar by pulling, then service may be needed to further investigate. Should you need to reach out to our team, they can be found here: spklr.io/6056iI06 We do hope this helps and that this is taken care of for you soon. -MS

[@jeank5254]

@@geappliances The lock bar broke off in the lock (seems to be a common problem, thus my request for an updated video). I had to purchase an entirely new lock mechanism and lock bar for a 1 day old washer 😠

[@geappliances]

Hi again Jean, Thanks for keeping us updated. We do hate to hear that this happened; know that we want to have as much information available and up to date as possible for our consumers to reference. If you have other questions or concerns about your unit, you're always free to reach out to us on Facebook or Twitter via PM/DM. All the best. -MS

[@karenl9731]

Why would anyone want to reverse the door??

[@dtxgmoney]

To be able to easily transfer clothes from the washer to the dryer without having to go around the open door.

[@geappliances]

Hello Garrett. You might need to reverse the door if your dryer needs to be on the opposite side in some homes. GA

[@williemonteiro]

The wondering minds wants to know. What is reason to turn off breaker?

[@geappliances]

Hi GnarlyRC. You turn off the circuit breaker if you do not unplug the washer. The reason is to make sure their is no power to the washer while you are doing the door reversal. Thanks for asking. ~RF

[@GabrielKramer-r5r]

How in the F were any of you able to get that little white piece of plastic out of there?????

[@SpunkMayo]

No dryer video? Dryer has security screws for no reason. Pain in the ass.

[@marcuspullan1142]

I just did the dryer door, no issues. Followed manual instructions and no problem

[@SpunkMayo]

@@marcuspullan1142 who asked you?

[@ryanchin9231]

bought a front load GE washer less than 3 years ago..paid almost $1400.00 for it....now it crapped out..been waiting for parts for almost 8 months now....after this long wait..they tell us that the unit is obsolete so they offered an exchange with one of these newer so -called ultra fresh washers for $450...and guess what? during the first usage..during the spin cycle..it start slamming against the membrane inside the unit and the noise is ridiculously loud.....called GE..they said call the service department...cant come out and service it for another 3 weeks....are they frigging kidding me?..folks stay away from GE...buy from another vendor like Samsung..LG..Electrolux ..just dont buy GE...they sell junk...and yes the unit is level.

[@geappliances]

Hi Ryan - We are incredibly sorry to hear about this frustrating experience, as it is certainly not something we would expect to occur. This must be very difficult for you, as washing clothes is quite important. Do you have a case number form speaking with our team about the situation? We would like to help in any way that we can. - TS

[@masonmccarthy9057]

Overpriced junk at best, people think more expensive is better when they're really getting ripped off.

[@jacobmarley2417]

@1:16 This step is dreadfully worded. “Remove the assembly by PULLING it towards the center,pushing it up and pulling it out” pulling towards the center -got it pushing it up- huh? in the video they dont use anything to push it pulling it out- so how do I push it and pull at the same time I am finding this step incredibly difficult to remove. Pretty sure i am going to break it trying to get it out. Would make it much easier to show how the teeth of this part secure to the door. I just got it and it and the directions are TOTALLY wrong. You should pull it AWAY from the center of the door. There is literally one small plastic tooth holding this in and if you pull towards the center of the door you will be applying tension on the tooth.

[@geappliances]

Hi Jacob, Thanks for taking the time to reach out. So sorry to hear about the issues you've encountered here with reversing your washer's door swing. We do hope that things are working properly now, but if you have other questions or concerns, feel free to PM us on Facebook or DM us on Twitter or Instagram with your complete model and serial numbers, as well as a copy of your comment here for reference. We'd be happy to review further if need be. If you need help finding your complete model and serial numbers, you can use this diagram: spklr.io/6058Y27w Best wishes. -MS

[@darinhouston1009]

That doesn’t work either.

[@geappliances]

Hello, We're sorry to hear this. Feel free to send us a private message via our social media channels with the model number of your unit, and we'd be glad to further assist. Take care. -SH

[@MrPburl]

DO NOT USE THE LOCKBAR!! That tool broke the lock mechanism. I was lucky to find a replacement part ($50). What a royal pain. Terrible instructions.

[@geappliances]

Hi there. We hate to hear that this happened while using the lockbar. This isn't expected, and we apologize for the stress. We're going to forward your feedback to the appropriate team for review. If you have any additional questions, please let us know. Thanks. -AT

[@masonmccarthy9057]

WARNING lock bar gets easily stuck and then GE will refuse to replace the jammed door, overpriced shitty units avoid at all costs!!! Modern day appliances are all a scam so don't be a dip shit and overpay thinking more expensive is better when they'll just crap out in a year or two anyhow woops hope you bought a warranty

[@nakedvader]

Thank you, perfect easy to understand video!!

[@geappliances]

Hello-Thank you for reaching out. We are glad you found our video to be helpful! If we can help with anything else in the future, let us know. We are happy to help!- DM