unboxing G660 92CC HOLZFFORMA STIHL CLONE! WHAT A G

#holzfforma #g660 #stihl

[@cajun3197]

Definitely the most saw for the money. I have one and I love it. I’m not even a stihl guy

[@majorpixchannel7146]

Money 💰 for money... absolutely the best value 👌

[@cajun3197]

@@majorpixchannel7146 yesh!

[@chainsawcanuck]

Every day is like Christmas in your shop! Lol that's a sweet looking saw

[@majorpixchannel7146]

Hoe hoe hoe lol 😆 🤣 😂 It really is a sweet saw! It's hard to go wrong with a 660! Awesome power! Tomorrow some time I'm going to do firts cuts with this one and the other big bore 660! Looking forward to that 😀 I also have one more saw tomorrow evening coming in! Lol

[@steelcityperformancesaws]

digging that color. keep up the good work buddy

[@majorpixchannel7146]

Thanks... thinking of sending this one on tour this spring!

[@majorpixchannel7146]

I answered the message notification.. thought you were on the grim reaper 660! Yes sir... the Grey and orange is nice!

[@cajun3197]

Ain’t nothin but a G thang!

[@majorpixchannel7146]

Chillin with a g 😎

[@espenhaugen9748]

Hi, have you shared any thoughts on the difference between the G660 and newer G660 Pro? Think it's worth the money to buy the pro and get the NGK spark plug, upgraged piston, and perhaps more quality control?

[@majorpixchannel7146]

So, in my opinion, the only difference is the plastics! Iv had both units torn down, and iv found both to be of equal quality! The nkg plug can be installed after purchase for under $10. So, the difference really comes in with the carbon fiber look alike plastics. Thanks for watching 👀 sir If I can be any help with anything, let me know

[@espenhaugen9748]

@majorpixchannel7146 thanks a lot for your thoughts and insights. Glad to hear it. Cheers

[@majorpixchannel7146]

Yes sir... Anytime

[@Ttow49]

I thought the pro had a better piston and carburetor and some other stuff?

[@joesmith-mt4ll]

What’s your gas mix ratio for break in and then regular term use 25:1 32:1 40:1 50:1?

[@majorpixchannel7146]

40:1 for normal broke in saws. And around 35 or 32:1 for break in

[@cajun3197]

The quality of farmertec cylinders have gotten a lot better and are in some cases actually better performance then oem believe it or not. Is it the same quality? No but the port timing on several are getting pretty aggressive out of the box.

[@majorpixchannel7146]

Yezzzz sir!

[@cajun3197]

@@majorpixchannel7146 😂😁

[@nicholasblohowiak29]

Wish I could say the same about my g660. Used it two hours. Now it’s in the shop. Isn’t getting enough gas and has an air leak.

[@majorpixchannel7146]

@@nicholasblohowiak29 that's to bad... sorry to hear about that! Still a quick fix.. get the corks out of it and you will be happy!

[@cajun3197]

@@nicholasblohowiak29 they will have their issues from time to time. Best to learn some basic repair skills if you’re going to own these.

[@keithrayeski6417]

New subscriber. Just ordered mine…should be at my door on the Thursday. Mine I believe is going to be blue. Is there a difference blue or orange? I didn’t see a color option when I ordered.

[@majorpixchannel7146]

Sorry for the late reply. iv been healing up from a surgery. There is no difference except the color! They are solid saws you will really like it! 👍 I'm a Neo-tec dealer now. They are much better on their customer service! Same type of clone and even better quality! If you are interested in another clone, let me know, sir! Thanks for watching 👀 🙂

[@keithrayeski6417]

@@majorpixchannel7146 I’m going to be doing some beating on her… responsible beating…I believe in taking care of my tools…but I’m gonna test her out!! I’m waiting on a neo-Tec 28” bar and chain. If the saw performs well…I may swap out some parts for OEM Stihl parts, like the recoil rewind…pretty consistent is the reports of failures of these. I don’t believe a guy has to be swinging a Stihl or Husqvarna to have a quality powersaw in their hands…so I’ll be playing with this saw fairly! I pray your surgery went well and was not too serious. 🙏🏻 Thanks for the reply!!

[@kdcustoms1272]

​@keithrayeski6417 how's it been? I just ordered 1 last night and a 25" stihl bar. I got the saw for $260 shipped.. just couldn't not buy it, even tho I really don't need it. I got a ms271 not long ago.

[@easingrapod1274]

Hi. I bought a G660 chainsaw again, but the idle speed is very high. How many revolutions should I set on the L screw?

[@majorpixchannel7146]

1 full turn out seems to work perfect to start tuning at! Cut your way into a log about 3 or 4 inchs. This is a excellent place to tune your saw! Very safe! I have a video on tuning a chainsaw! What is lean and rich. How to tune a chainsaw. Look it up sir

[@majorpixchannel7146]

kzbin.info/www/bejne/f2e0f3qDjZmajpYsi=l3J139OiIosuesD7 This is the video... This will help you with tuning your saw

[@easingrapod1274]

@@majorpixchannel7146 Thank you! Sir :)

[@easingrapod1274]

@@majorpixchannel7146 13180 is the maximum revolution I set, I don't want it higher than that. Do not damage the machine

[@majorpixchannel7146]

@@easingrapod1274 That is a good idea sir. Makes for long lasting chainsaws

[@logankosik3820]

What fuel mixture ate you running? i just bought a g660 but already have an actual ms660 and i run 50:1

[@majorpixchannel7146]

So I run 40:1 in my clones..and 32:1 for the first tank. But, 50:1 would work just fine. I just like that extra bit of oil to lube while milling.

[@easingrapod1274]

Hi . So far I have used 2 tanks of gasoline with the machine, what is the speed of your machine? Did you perform a carburetor fine-tuning when you ran your machine? After how many tanks of gasoline do you adjust the carburetor?

[@majorpixchannel7146]

So I normally run my saws rich 1 3/4 turns out tell break in. (About 3-4 tanks) Then I tune it to spec! You.can run 14,200 ... but I like to run 13,400 in a good work saw! Thanks for watching 👀 sir

[@easingrapod1274]

@@majorpixchannel7146 so far I was able to work with 2 tanks because it rained all week, but I want to work with 2 more tanks

[@majorpixchannel7146]

@EASING RAPOD perfect plan, sir... I wish we had the rain 🌧 in Oklahoma...

[@easingrapod1274]

@@majorpixchannel7146 We had a drought all summer, there was almost no rain, the ice damage protection machine was activated and we think that's why there wasn't enough rain :( Sir :)

[@majorpixchannel7146]

@@easingrapod1274 we have had a drought as well... all summer and now the winter! I have roads that we have to run a water truck on to keep them from. Turning to sand! We need rain 🌧

[@nicholasblohowiak29]

I bought a g660 from justsenditsaws. Used it approximately two hours. Now it’s in the shop. Super bummed and a little irritated.

[@majorpixchannel7146]

I totally understand... I have purchased 50-60 or more clones! And only had a out of the box problem wonce! Now, it I was not able to turn wrenches on them... I might feel different! I have had many stihls apart and holzfformas... the quality is close! The money 💰 is far apart!

[@nicholasblohowiak29]

@@majorpixchannel7146 is it true that the parts are interchangeable?

[@majorpixchannel7146]

@@nicholasblohowiak29 hey, sorry about the late reply... yes sir it is! All parts! That's the upside of the clones! You can always replace parts with oem! On my machines I still use the holzfforma parts because of the cost and my ability to repair. And I like working on them! I mill with my machines... with a norwood pm 14 sawmill! Nothing puts a saw to the test like chainsawmilling! Sorry about your experience with yours... if you have problems in the future let me know and IL make a video on the issue your having for you can do the repairs yourself! Even if it requires me coaching over a phone IL help you! My only interest is to help! I'm always here to help with repair coaching, questions or what ever!

[@nicholasblohowiak29]

@@majorpixchannel7146 oh it’s all good. Thanks for the reply. Greatly appreciate it 👍

[@easingrapod1274]

Hi. One of these machines that I ordered will arrive today. What do you think of the machine?

[@majorpixchannel7146]

They are truly nice machines... I have milled about 50 logs with this one so far! And I have other machines like it that I have processed 100s of logs! Treat it good and it will treat you good! If you have any problems let me know and I can help! Thanks for watching and welcome to the channel

[@easingrapod1274]

@@majorpixchannel7146 Thank you sir. I'm not American and I'm using a translator. But I'm glad that he wrote well about the machine and reassured me.

[@easingrapod1274]

@@majorpixchannel7146 I own a Stihl 311, a Stihl 231 and an old Husqvarna 55. And now I bought this Hollzzforma G660.

[@majorpixchannel7146]

@EASING RAPOD you are welcome, my friend ! Anytime I can help ☺️

[@majorpixchannel7146]

@EASING RAPOD those are nice saws brother! I love my 55 Husqvarna 😁 Thanks for being careful about. Be easy with the chain tensioner! I, always pull out on the bar as I put tension on it to help! (But I do this with oem saws) clean the filter after every use! Besides that, you are good to go!

[@steelcityperformancesaws]

can you buy those skid plates separate?

[@majorpixchannel7146]

Yes sir from holzfforma... im thinking 🤔 of making some! Thanks for waching brother