Understanding The Creep, Creep material data, Abaqus material card and Abaqus creep analysis

[@kanhucharansabat8022]

Good one

[@abaqusacumen7397]

Thanks for the visit

[@Zain18356]

great video explaining creep process in ABAQUS, Do we have to give G0/G1 or G1/G0 as shear compliance

[@gautampj1]

Brilliant job!

[@manognareddy3415]

Glad to see your videos as always

[@abaqusacumen7397]

Glad you like them!

[@shapuyzat]

nice tutorial again. why did you give up to make a live stram last day? could be good to meet online...

[@abaqusacumen7397]

Next time

[@SandyTalks..]

Sir, I have tried inputting the creep test data instead of relaxation data as per the process mentioned here.But every time I come across an error" No convergence for any order n". I have used uniaxial creep test data performed on asphalt material. Could you help me in resolving this sir

[@InnerVoiceofthepeople]

Are you Providing any Paid Training Online/Virtual for engineers already having some basic Abaqus Experience. I sent an E-mail to you . Thank you so much for sharing your knowledge and bringing simulation to real life problems

[@abaqusacumen7397]

Not yet

[@InnerVoiceofthepeople]

@@abaqusacumen7397 thank you sir . I sent personal email few days ago

[@muhammadimamammarullah6602]

Hello mister, I have problem with ABAQUS. I want to simulate half-ball to cup contact with 0.05 radial clearance. How to remove gap because of radial clearance, so the two surface will contact ? I really need your help

[@ahmetmunirozdemir200]

Hi. Im facing this problem: NO CONVERGENCE FOR ANY ORDER N FOR THE VISCOELASTIC SHEAR TEST DATA

[@hayriburakyalin]

Hi Could you add a video about how to design laminated glass in abaqus program?

[@z4961]

Thanks for the video

[@YogeshKumar-tg3uo]

Hello, Can you please tell me how to find the gR or jS values which we provide in Abaqus while finding the stress relaxation?

[@baranbozkurt3263]

if you solve the license issues, can you please make a simple example about creep analysis?

[@hellohai8720]

Sir please make a video for cyclic performance of corrugated steel plate shear wall with beam only connected infill plates

[@anupekbote]

@abaqusacumen7397 Although the question I am asking not related to the topic of discussion; however if you can help me it would be of great help. Sir, do you know any thing about the error: "There is zero VOL. FLUX everywhere in the model based on the default criterion. please check the value of the average VOL. FLUX during the current iteration to verify that the VOL. FLUX is small enough to be treated as zero. if not, please use the solution controls to reset the criterion for zero VOL. FLUX."

[@dattarsingh6610]

hi. can you tell me how to get mode shape vector after modal analysis to get MAC value with experimental results?

[@civilbuild7058]

Bro can you create a tutorial on modeling masonry brick wall under diagonal loading

[@yogeshkumar114]

Hello Abaqus Acumen, Greetings from Germany. At slide where you are explaining how to get abaqus data from Isochronous curve, how do you calculate G(0)? In this case there are only E(1), E(2)....E(n). But how to get instantaneous E, which we need for calculating G(0). Thanks YK

[@abaqusacumen7397]

it is modulus at time equal to few sec or mins.

[@usannand]

very nice explanation but few question related to abaqus, 1. Moduli is long term or Instantaneous 2. since you are updating *visco elastic , i hope viso-elastic and creep or different (correct me if am wrong )

[@abaqusacumen7397]

Moduli is instantaneous and Visco elastic and creep method in abaqus is same.

[@usannand]

@@abaqusacumen7397 method is same but concept ??

[@usannand]

@@abaqusacumen7397 very good class .. Expecting more from future ..

[@panduranggalande9602]

Nice, one thing I want to add is in primary region the slope is decreasing and not first increase and then decrease.

[@bai3haGamer]

Great Video ! please do the simulation process with experiment data on ABAQUS, I absolutely loved this video.

[@abaqusacumen7397]

Great suggestion!

[@lawrencehuang5039]

Dear Abaqus Acumen teaching team, Thank you so much for your video! It is really helpful. Would you mind making a tutorial about the abaqus scratching simulation set up? Thanks and best regards,

[@UppadaRamakanth]

Sir good information. PL do this simulation in abaqus with experment data

[@maattallahkarim7557]

Hello sir .. my name is karim and I m student .. l trying to do a spur gear analysis with abaqus ..some edges or teethes of gear doesn't contat with the other gear's teeths and don't show a result .. please can u make a tutorial on your youtube channel 😍 😪

[@abaqusacumen7397]

I will try

[@mariogalindoq]

I think your formulation is wrong. You are obtaining G0/Gt but taking about Gt/G0.

[@mono7891]

How ironical that such educational videos get only 125 likes whereas Kardeshians get million likes just for posing in bikini and bra around the pool !!! Great explanation !!

[@MrAberra]

hi

[@Amansingh-he2yn]

Sir i have some doubts in ABAQUS how i can reach you ? Please share ur mail id