UNI-T UT 511 Insulation Tester, Review and what to do with it

Here i will show you the Insulation Resistance Tester UT 511 from UNI-T and what kind of measurements are possible. The UT 511 is the cheapest tester in a series of 3 models. The price is from about 100 € (UT511) up to a bit more than 300€ (UT513).

[@poeml]

Very nice demonstration, thank you

[@takbunthorn6153]

I like your review...... please adding more about the insulation test.

[@slime904]

Thanks! Quite helpful video.

[@KAMERKURUM]

Thanks for giving information insulation tester.

[@GuillermoLeib]

Good walkthrough. Thank you!

[@mortenlund1418]

Thanks for sharing. Perfect

[@autotechnik665]

❤️💪Thanks very mutch for the video! 🤗

[@Musicconfigworld]

Thanks

[@emmanuelagyemang8519]

Thank you sir

[@CatPixStudio]

Great review! Thanks! Is it possible to set the 1st timer to 30sec and the 2nd timer to 60sec to calculate the dielectric absorption ratio? Or is it even already implemented?

[@mse6424]

yes, you can set each timer between 5 seconds and 29:30 minutes by pressing the timer button and than the arrows right/left.

[@30mAkills]

Useful

[@faisalnawaz7467]

I have same with me in our project to perform IR but it show OL even when perform IR and Resistance bar goes up

[@grerlab2777]

Thanks for the video... will there be more videos with the use of the UT511...?✌

[@mse6424]

Hi, thank you for your interest. I´m thinking of more things i can do with this instrument, but right now it's not enough for a new video. (i.e: you can check the leakage current of capacitors.... but be very careful handling the tested caps!!!)

[@MadaraUCHIHA-hy9xe]

Thank you for the review But they should change this type of battery

[@pengawaspenyerumalutaubat8365]

Indonesia👏👏👏😊👍

[@marius.verdes]

Hi, you can make a video with a ground measurement at home?

[@mse6424]

i will try to make one next time...

[@ahmadclips]

Very informative video please share reviews of UT 513A

[@mse6424]

Hi Muhammad, as i bought the UT 511 for my workbench, i have no access to the UT 513. But the procedure will be the same

[@MadaraUCHIHA-hy9xe]

What's your opinion about the device ?

[@mse6424]

Hi, sorry for late answer. Though it has limited purpose, I`m quite satisfied with this device. And yes you're right, this type of batteries is a mess :-)

[@jercysanchez8531]

A consult... Test DAR?

[@srinivashbhoi2226]

Why its shows OL On Screen.?

[@mse6424]

Hi, measuring current or voltage with a multimeter, you have to choose the measuring range on the meter (if it's not a autorange...). Lets say you set the 20V range, that means the meter will show values up to 20V. If you have 21Volts on the meter Input, the meter will show "OL" for OverLoad (the voltage is too high to be displayed). Then you have to switch to the next higher range: 200V. The meter will now show 21Volt. If you are measuring Resistance (Ohms) and the TestLeads are open, the meter will show "OL" for an Open Loop. If you shorten the Test Leads, or put a resistor between (inside the range!) the meter will show the value.

[@mihaipopa2330]

@@mse6424 OL = Open Loop not OverLoad!!! And has nothing to do with voltage to high but with resistance to high in Ohm measurements.

[@ahmadclips]

UT 513A operation