UniFi: Beginner’s Guide to Network Cabling | Part 2 - Home Installation with UniFi Design Center

[@williamjonson6845]

No need to untwist the pairs. You can use the plastic to slide the wire over while trying to retain as much of the twists as possible to termination.

[@jadamsnz]

Tip: make sure the cutting blade on the punch down tool is always on the outside of the keystone jack.

[@N1njaNick]

I made this mistake my first time using keystone jacks. Luckily it was an easy fix.

[@austinreeves5221]

@@N1njaNick SAME! first day on the job and had no serivce loops. Boss made it work but i was like never again.. it was on the rack side

[@troywaller77]

That particular low voltage box (Carlon) has four small holes near each inside corner... that allow you to mark the corners on the wall of your cut line and get your layout lines for what to cut out the sheet rock very accurately. Just FYI

[@andrewenglish3810]

Just so you know those orange wall plate brackets have 4 little holes at each corner, if you take a pen and draw a point on the wall at each corner and then line up the point you have a the perfect hole.

[@TomZ23]

5:53 Why such a big hole for one cable? That leaves a pathway for G-forbid fire. Again, as stated, the key is to check local codes. They are pretty tight where I'm at in the US. Metal conduit is still a thing for AC power. I've always used fire block sealant around any penetrations through fire blocks or top plates.

[@MactelecomNetworks]

Nice video very well done

[@jodycwilliams]

Always punch down against a stable surface. Those plastic bits snap off very easily. Otherwise, great video.

[@jaysimmons9598]

Thank you! Been doing this for years but it's a great source for my clients to see. I share it often.

[@SeanBasile]

This is a great series! Keep them coming.

[@brysi]

I agree!

[@Linkall]

Shielded CAT6 allows adjacent power runs in situations you cannot escape

[@pfunkPT]

Very informative. How about audio HI-FI cables? Can those be run together with CAT6? Will there be noise interference in either of them?

[@scorpio21x]

You should mention any holes in the top plate leading to the attic should be air/fire blocked otherwise warm moist air will enter the attic and cause mole and rot. As others have noted, consult the local building codes. I like great stuff expanding foam for this purpose.

[@benbrooo]

This is what me my dad and me do!

[@ntech7553]

thank you for sharing

[@Timi7007]

As a european north american building standards are always quite interesting to see 😅

[@lrojas26]

What size drill bit did you use on at 6:00 minute mark?

[@saltyroe3179]

The "dental floss" is a strength element to prevent damage to cable from stretching.

[@OthmanAlikhan]

Thanks for the video =)

[@louiem5985]

Question for you. I just moved into a house that had the power and network cable coming down from the attic together. I notice the electrical wire is wrapped in a purple shield wrap. Would that be okay to still run it together? The reason why I'm asking is beacuse it's only one hole they ran all the cables threw. This house came pre-wire with cat5 and I'm upgrading to Cat6E

[@xaj]

Anyone know what kind of J-Hooks he is using in the video? I like the one screw install and angle bending he’s able to do to level the tray/bottom

[@unalakdogan9416]

Hello, can we connect your nanostation m5, m3 and loco m5 devices to each other from the ethernet ports on the poe?

[@Timeless42069]

Great Vid! Where can I buy those J-Hooks for the rafters? Thanks in advance

[@pmurray0511]

What tips do you have to plan runs through walls with fire blocks? I live in a townhome and I have done some runs but drilling holes in my upstairs ceiling. I need to come down the walls for my downstairs but I don't know a way to plan a route with the least amount of obstructions without x-ray vision.

[@Deraco1]

Most of the time when you run into this, if it's wood, is to get a long drill bit and drill through the blocking

[@iguesi]

Do NOT hold the keystone in your hand and punch down, unless you like to leave your blood on the jobsite. Punch down on a solid surface. He even had the block for holding the keystone and didn't use it. We you put the faceplate with the keystone in the wall, have the wires on the top side... it helps to protect them from dirt.

[@mikeheck4998]

Schlitze klopfen mit dem Meißel, leerrohr rein zu gipsen. Kabel ziehen, Fertig. DIN und VDE beachten und LAN separat von den 230/400Volt Leitungen verlegen. Deutschland Kabel verlegen.

[@New_Identity]

Fewer videos, more shelf stock please :p

[@brasilianloser]

Had an electrician run wires for me in my new home that is under construction. The horror when I saw they run all the wires and didn't use a single j hook. Instead stapling all of them in sets of 2 every other board. The nightmare that will be upon me when I decide to replace my runs in the future will probably end my life and my pocket book because I am definitely going to have to pay someone to do it for me... Bad back and all.

[@yourpcmd]

Do you as a company plan to stop deceptive practices?

[@johnadams1976]

I have had so many network cables that have had to go near electrical cable. It's been absolutely fine... Just laid across rafters in the loft out of the way has always worked for me. All these extra hooks just aren't necessary