Upgrading Jumper T-Lite with Radiomaster AG01 MINI gimbals

[@dashfpv]

Great video! Those wires colors are opposite. I rewired it all to make sense too.

[@mortalwombatfpv9386]

worked perfectly on my v1 i did run into the throttle gimbal hanging up during test fitting the shell but that was due to it contacting the larger gauge positive wire i have running to ext module straight from the battery so a slight re route and smooth as butter. that you again the pinout was very helpful since i decided to go the soldering route cheers

[@whooperfpv]

Thanks for showing how to do this. I changed my Tlitev2 gimabals to stock RM zorro gimbals. Very nice

[@MrAndrucho]

Hello! Great job! Tell me, what means are the contacts sealed after soldering? I'm going to upgrade my t-pro v2 in the same way

[@cosinusquad4054]

I have done it, too. It is really great. Thank you for your help and the idea.

[@brianfreland9065]

I have the same radio, the same elrs module and the same gimbals! ❤

[@lucien420]

Thanks. I did mine tonight.

[@djs134]

So the right gimbal is plug n play and only the left gimbal needs to be soldered like in the video?

[@lucien420]

@@djs134 it's been a while since I did it. I'm pretty sure you have to do the same thing to both sides. Biggest thing is to pause it on the pinout to make sense of it. I'm pretty sure I lifted the tabs in the plugs and swapped wires to appropriate colors.

[@alanshearing7515]

Hi, I have just upgraded my Jumper light V2 . With the new LRS power supply things are even easier (doesn’t need to be moved ) . Also as a note I know you did it , it is important to bend the gas resistance tab over at the end otherwise the back won’t fit ! ( battery box ) . It is to be seen in the video. Thanks for taking the time and trouble to make this video 👍

[@blakey271able]

Is the weird wire color diagram still the same correct as in the video on the v2. I've recently purchased one and just looking at upgrading it. Thanks if you can reply

[@alanshearing7515]

@@blakey271able All looks the same to me , I can’t imagine that anything’s been changed. But no guarantee that the V2, is different.

[@cosinusquad4054]

Great solution. Great work. thank you!

[@michaelhill7261]

Good job on this 👍, I might have to try it myself.

[@sendorm]

Hello great work. What product do you use for antenna glue? Thanks

[@gasparzinhorb]

Very good, will it work on the jumper t-pro?

[@RobertoMartinsInfo]

I have the same question

[@JannoSiimar]

no, there is not enough room in the radio for that gimbal .. you have to remove the "ears" .. i glued my gimbals in after that ..

[@blakey271able]

Does anyone have more advice on this like the part where he changes the wire harness to make more sense so is the pinout shown at that point correct or modified I'm confused and would like to understand what I'm doing

[@michaeltrooth2631]

I've been looking into this for for the last couple weeks, have one in a molded 3d printed shell, elrs, 2 1s lipo and the gimbals were the last step. Will be ordering these, thank you for sharing this. Just needed to know if the gimbals would fit and we're compatible. Awesome

[@Martipops]

what wattage do you run your elrs module at?

[@michaeltrooth2631]

@@Martipops indoors/tinywhoops 50mw and below. Outdoors 100mw, I haven't outflown this on a 200mw HDzero vtx even at 50mw. Module will do 250mw tho, might wanna add a fan and better/bigger battery.

[@TERBANGFPV]

In this video you only colour corect the 4pin wire right? If i dont want to solder, can i just make a Y cable? 4pin to 2 3pin wire?

[@OVERKILLFPV]

Good job!👊

[@djs134]

If you Dont plan on using the external bay couldn’t u just remove the elrs power bay that u moved over ?

[@bengordon7635]

this is the same for the jumper t pro ???

[@Anziilife]

If these fit in the Jumper T-Lite.. Is there hope for Tango and Mambo too?

[@Iliveforanxiety]

Wait is this the v1 or the v2 t lite?

[@rainfizz]

hi no new videos?

[@Fpv415]

This is jumper t lite v2?

[@manjofpv1725]

is this mod possible with the numoer t pro?

[@superiedyfpv8666]

hello it was a long time that I was looking for this solution I congratulate you for the excellent work. I just have a doubt, when you redo the wiring at 3.48 minute you balance the reversed polarity why?

[@aigilea]

I've changed wire order for the Jumper connector on 1:47 for colors to make sense. So on 3:22 I have black as ground, red as vcc, white and yellow as outputs. After that I solder ag01 wire harness that in my case (but maybe not in yours, so check the pinout at 1:25) has red as ground and black as vcc, so in the end polarity is correct. Good luck!

[@dhomenow]

@@aigilea nice one! I'm still confused, at 3:31 you wire horizontal black wire with vertical red and visa versa, can you explain why?

[@MegaCABE93]

My ag01 has on pad 1,5v for red wire, s for yellow and Mt for black wire ... I try youre electric diagram but go in shor i think, because the battery check show me 100v and all the value of axis show me 100 and don't move

[@MegaCABE93]

Sorry, i miss understanding, the variant thath show 1,5v on the pad, is also + and - inverted, now it works

[@gleuvaferreiradasilva3979]

ello I'm Brazilian I saw your video I really liked your work congratulations it was very good I have a radio jumper t pro and I would like to upgrade like this, could you tell me if I can do the same upgrade you did in the video with my radio jumper t pro?

[@aigilea]

I don't have a t-pro so I can't give you a definite answer. Start with measuring the gimbal face, if it's 37mm in diameter than it's probably possible to perform the upgrade, but it will be a bit harder compared to t-lite. Judging from t-pro teardown videos it has mostly the same gimbals with two notable distinctions: 1. Mounting screw locations differ, screws are located closer to the gimbal itself and they are now flush with the gimbal plate. You may need to modify new gimbals (cut off original screw mounting sockets, drill new holes for screws) to make them fit. 2. One or both axis MAY be inverted as vertical sensor board is placed on the other side of the gimbal. IF that's the case you may need to get creative with gimbal/sensor/magnet rotation. Or you can just fix inverted axis by setting weight to -100 in mixer, it will work fine but stick indication on the radio screen will stay inverted.

[@gleuvaferreiradasilva3979]

@@aigilea hello my friend i would really like to adapt these gimbals ag01 mini in my jamper t pro i as soon as i saw your video i soon bought a pair of these gimbals and tried to adapt I even managed to make them fit well on the radio but when I tried to deal with it, it didn't turn on even though I took great care in the solders and followed the step by step of your video

[@manwithgutz]

the pinout is abit misleading can u do another detail video why the wiring has to be swap and do we need to do it for both gimbal ?

[@toodlesg1c]

Some news? I‘ve the same question.

[@ramboaripratama1992]

hello it will work for betafpv radio lite v2?? thanks

[@F-ItSeNdItFPV]

Thank you very much for this video I did the same upgrade and it works great 🚀✈️🛩️🤙