Your Underfloor Heating Could Be Better - Here Is How.

#UFH #underfloorheating #radiantheating
In this video, I show you how to bring your underfloor heating to a modern standard and how to make sure it will be compatible with a heat pump in the future.

[@AnthonyHigham6414001080]

The resistance to new methods in the construction industry is astounding. It took me twenty years to persuade architects, contractors and clients that underfloor heating was a good idea.

[@QnA22]

How about wall heating? Also something you don't see a lot.

[@konobikundude]

One word; Insurance.

[@jimd5983]

I can't find a heating contractor with experience with panel radiators which are next best and for an old home best choice. They all want to keep fin tube baseboard because its all they know.

[@adrianred236]

In my expieernce, Architects tend to be pretty useless with few exceptions. Anything they design, someone else has to figure out how to build. And they're super power is blowing budgets.

[@AnthonyHigham6414001080]

Mine too. In forty years of construction I've met just one architect who had a background in engineering. He was a joy to work with. @@adrianred236

[@andrewmillwardwatford9410]

It is often the case that when the boiler is running on night setback a mixer will be required on the radiator circuit. This will depend upon the Delta t at the boiler and the design flow temperatures for the radiators in relation to the underfloor heating. A good rule to remember is that the underfloor heating will require a flow temperature to its mixer higher than its return to temperature by the Delta t at the boiler or the hydraulic separation. It's also worth noting that the hydraulic separation works in exactly the same way as a mixing valve for the highest temperature zone in operation. So for example if radiators and underfloor are working at 55 and a delta t of 20 for the radiators and 35 at a delta t of five while the boiler has a delta t of 20; the underfloor heating mixer would require a flow temperature to arrive at its variable temperature mixer of 50 degrees and the radiators would require the temperature of 55. To achieve this the boiler would not run at 55 but would run at a higher temperature to feed the low loss header where the first mixing would take place for the system. Here the higher flow rate produced within the system would be blended to 55 degrees to suit the radiator system and the underfloor heating variable temperature mixer would reduce the temperature from 55 to 35. The problem occurs when we want to run the radiator zone at a lower temperature during night setback for example. At this point we may need a flow temperature to the radiators lower than the flow temperature for the underfloor heating. In this case we would need a variable temperature mixer on the radiator circuit to enable the radiator circuit to run at the lower temperature then the underfloor heating. This phenomena is not an issue when you're working on heat pumps where the Delta t of the underfloor and the radiators and the heat pump are matched. I learn this the hard way when I had to return to a number of jobs to fit an additional mixer on the radiator circuits following complaints from customers of overheating bedrooms during night setback. There are ways of coping with this problem for example on the veesman boiler you can turn the radiators circuit off at night time to prevent the issue but many people want to have the use of nights at the radiator circuit to prevent excessively cold bedrooms and this control his only achieved if it is fitted with the variable temperature mixer.

[@PaulSmith-pr7pv]

❤

[@robharrison6918]

Well done. This is what I am promoting through my business too. The Vaillant controls work very well and I won’t give customers the option of anything else. I sell efficient systems not half arsed ideas. I have sold system control to customers that had boilers put in and left on S or Y plan. I have also asked other installers why they don’t do weather compensation. They belittled the customers by saying they wouldn’t understand it! I find the older customers more receptive to upgrading. One last year, after we removed a floor standing ideal and put a new boiler, 2 rad zone and hot water, weather compensating system in, said his gas consumption had reduced 30% from the previous year. Now that’s a pensioner. He is very happy. Thank you for your explanations and encouragement. I hope more installers will take the time to understand how to be better at installing low temperature heating.👍👍👏👏 dobrze zrobiony.

[@LocostR1]

I'm so glad you made this video because from the vast majority of UFH videos (looking at you Skillbuilder) you'd think mechanical mixing was the best and only way to do it. This is exactly the combination of Vaillant controls and Esbe valves controlling a UFH zone and a rad zone we had installed by Andrew Millward a couple of years ago after we had issues with the original fixed UFH mixing valve and 3rd party "smart" controls that actually just turned the boiler on and off on a schedule. The new setup is SOOO much better, having determined the right WC curves for the UFH downstairs and rads upstairs with a bit of trial and error, our Ecotec 630 runs pretty much 24/7 at minimum temperatures, keeps the house temperature far more comfortable and consistent, yet still saves us about 20% compared to our gas consumption with the old setup.

[@UrbanPlumbers]

Great! Those systems really work very well. Skill builder needs to take notice and come and learn how to do UFH properly from us and not promote slack of proper design and control

[@andyhodchild8]

Viessmann had schematics for this independent weather compensation set up 25 years ago. The UK just love on off switching.

[@UrbanPlumbers]

Yep - my family has 25 years old viessmann WC set up in Poland. UK is sooo backwards when it comes to heating

[@defragsbin]

@@UrbanPlumbersDo you think it's partly down to the UK having a temperate maritime climate and a lot of coal, oil and gas? In countries with less forgiving climates, it's not an option to half-ass installs, so you have to do it better by necessity. I feel like the UK got away with being lazy for so long -- why bother insulating homes or designing systems properly if you can just burn more cheap gas, instead? Those days are over, so I am hoping there'll be a bigger focus on improving things. I just wonder how we fix this malaise, as we must be throwing away billions each year due to bad installs and inefficiencies.

[@rodgerq]

​@@defragsbinI think it's a case of a few problems. Being a country that is simply resistant to change. The old saying "this is how it's always been done" is just so ingrained in our way of thinking. People get comfortable doing things a certain way, are happy in their comfort zone bubble and don't like to hear that their ways could be improved. British exceptionalism is absolutely a thing as well.

[@andyhodchild8]

@@rodgerq I think that the public are I'll informed and so you start off with ill informed customers. I always tried to 'sell up', I remember trying to sell condensing boilers in the early days, early 90's, and it was hard. There were issues with the technology but the trade were very hostile. I agree about British exceptionalism which has always been a crazy xenophobic thing. I travelled in Europe in early 80's and most things were at least as good as here and many things were much better. Only central Europe was having a hard time under the dying days of soviet rule.

[@rodgerq]

@@andyhodchild8 And when you go to Europe now, they have it so much better than some parts of the uk. The public is definitely ill informed, that's true. But also don't like taking expert advice. I'll never understand this push back from people on new technology either, whether it's a heat pump or an EV car, there is a cohort of people who just pick fault with anything new. It's so weird to me why any progression is seen as a bad thing.

[@pt6423]

Very well explained and makes perfect sense. Your philosophy on heating is on another level.

[@enm22]

Childish I know, but first, that said your installs are a perfect example of craftsmanship and attention to detail, thank you for your skill

[@markrainford1219]

Wiring is very messy.

[@stewartstewartstewart]

What’s the deal with the sentence? How is it childish?

[@enm22]

@@stewartstewartstewart Writing "First" as I was first to comment, childish, so unworthy of further comment ;)

[@Josh__Stevens]

I absolutely love your attitude and you are 100% correct on your talk about old methods and people not wanting to learn or expand their knowledge. As a Technical Manager (apprentice served electrician) for a business that’s owns 6 holiday parks, there are some really good methods and mindsets that you convey in your videos (weather comp etc) that i will look to deploy on our parks to make existing systems more efficient. We have loads of accommodation with UFH and Heat Pumps as well as traditional LPG Boilers. Thank you for sharing your knowledge!

[@EliteHydronics.]

Great vid. we advise no pumpset and blend, actuators but try to convince the masses. controlling emitters dynamically in real time has so many benefits.

[@neilbissett1240]

Top notch as ever and top channel 🤔👏😎

[@loving-plumbing]

Great informative video as usual. If you are wondering if engineers watch your videos and learn from them, I certainly have. Thanks

[@stixstonesinvestors5413]

Still cannot get enough of this channel. You are unreal geez. I just love learning from you, blows my mind. It’s a shame so many are stuck in there ways and don’t want to learn this. With ya all the way bud and thanks again for your effort in doing these vids 👊🏻

[@markgarnham748]

So refreshing to see a heating engineer who looks to provide customers with a setup that is fit for purpose and set to run as efficiently as possible, there are so many installers out there that are just interested in sticking a boiler on the wall without any thought about controls or setting things up to run for the good of the customer which is scandalous really when a lot of equipment built these days has so much more to give than an on/off setup and could be being used so much more efficiently with modern options.

[@sambutler927]

I agree with your point. On the flip side allot of clients don’t want to pay for quality and they are not interested in complicated set ups which will not save you enough to cover the extra outlay on installation, set up and the cost of the controls. That’s a fact.

[@Kris_M]

@@sambutler927 "not interested in complicated set ups which will not save you enough" But Urban Plumbers is in almost every case simplifying the setup and making them more efficient. Why wouldn't clients want that? I think it's rather that too many installers don't care and just want to move to the next job as quickly as possible.

[@sambutler927]

@@Kris_M yes you are right. Szymon is great. I’m referring to my experience of the majority of our customers couldn’t care less. They just want something that works for as little money as possible. And fancy controls can quite often cost more than they will ever save 👍

[@Kris_M]

@@sambutler927 Hmm, yeah, that VR70 and VR71 comes at 209 and 259 euros. If installers are adding margin on top of that, it might look (too) expensive for some.

[@sip5574]

With respect, many many many gas engineers have never been given the training to know how to design, install, commission and maintain CH systems to the level of the elite guys. In previous videos Szymon has mentioned about some of the training he has done (kimbo, heat geek), and the knowledge gained from doing those courses is career changing (was for me). Unfortunately training centres, NVQs and most training books don't cover what heating engineers really need to know, and it's only the guys that have the money, time and drive that will end up going on those course, completing and comprehend them.

[@rodgerq]

Great video and great points im merely a consumer but tend to delve into things when im looking to make purchases. I got a quite a while back for an UFH settup and it was rhe standard mixer and pump on a manifold. Whwn i asked abiut separation from the radiators i was told it wasnt necesary, nor was a heat loss on the space supposeldy. I declined the quote there and then. In the meantime i have fitted a tado thermostat which can modulate the boiler until i decide where to go. Ideally a heat pump and full UFH but its a pricey game.

[@copperskills3973]

Been fitting ATAG boilers lately with there diverter valve and DHWP. Amazing set up and very simple to install

[@markfernandes2467]

I've heard good things about ATag. Pricey though right? Also, no one ever fits them. They stick with what they know I find. What areas do you install in ?

[@andrewriley4204]

Agreed, the ATAG systems offer equally good options for PDHW, and varied temp (Low Temp), Heating circuits, oh and Weather compensation

[@hiltonshaw5528]

The last comment is the best !! Great video my friend

[@elringoRS6]

Thanks for making these videos. Would love to see that Vaillant Hybrid one if it ever happens.

[@UrbanPlumbers]

Thank you !

[@wittorito]

Hi. Thanks for all your videos. In house i have mixed system radiators with wet ufh. Whole system working ok with 35 degree water temperature set as standard. Flows on diferent circuit set with use of thermal camera. Not shure if really need zone acurators. Planning just ad second hive thermostat for ufh as one is instaled on radiators .

[@erhantimur]

Only an expert can explains things so simply. Brilliant explanation. Thank you.

[@UrbanPlumbers]

Glad it was helpful!

[@Brijoolz]

Totally agree with what you’ve said. Physics is physics at the end of the day. I was involved a few years ago in a large property which had a mixture of underfloor heating on one level, rads on the upper floor and two unvented cylinders. If I’d removed all the unnecessary valves, actuators, control wiring etc, I could have saved the planet with all the needless mining!! Although we eventually had a working system, due to the poor design (our own it has to be said), the floor temperature was always too hot. I read something at the time that said if the floor temp was over 27oC, it feels uncomfortable to walk on. This, if I’m being honest, proved correct. Took me all my effort to give them something that heated the house. Just a shame we started from the wrong place due to bad design. Thanks for showing the way. Keep at it sir.

[@Efficienthydronics]

awesome job as always mate!

[@dickie997]

Very good video, well done.

[@MaxMakerChannel]

Can you give your advice on the connection diameters of circulation pumps? I see a lot of DN25 pumps even though I have a DN40 pipe comming in from my heat pump. I am a bit confused why the manufacturer have such small couplings.

[@guygfm4243]

very good clear to the point.

[@kizzab93]

Great video, as always. Do you have a video of the installation and set up of the Vaillant controller, and how the individual temperature monitoring works? Thanks

[@TheRpjenner]

Interesting. Nothing new but 30 years ago nobody was interested. Been doing this and much, much more for decades hardly anyone maintaining it understood. Keep up the good work.

[@sroberts605]

Actually that was my main concern - more sophisticated, better, but... more to go wrong?

[@dailyreader506]

Exactly. The system must first be designed to match the conditions of the building and seasonal weather variations. Selection of appropriate equipment and controls. Installation costs must be measured against the low operating costs and savings. That design expertise is crucial. The same issue exists in using energy efficiency building design software (e.g. passive heating and cooling). I appreciate your comments on upsizing circulation pipes to reduce friction losses and pumping costs. Same for reducing maximum required temperatures and being purpose specific. The improvements to building insulation to complement the system is also a very important consideration. It’s all about lowest operating cost- the savings you pay for by good design.

[@joncarter2178]

Great video!!

[@johnc4323]

Great video, great explanation

[@UrbanPlumbers]

Thank you!

[@312523546475734673]

Great video, lots of information and clearly explained

[@robertgreenaway5166]

Thanks for the video. Could you do a more in depth look into the wiring controls and setting up the boiler with hot water priority and weather compensation, setting the different flow temperatures on vaillant. Thanks

[@myatix1]

Very interesting! Thanks for sharing! QUESTION: can you share some more details about the KimboHeader?

[@rustytravelboyrob6181]

Terrific video again. Thank you. Learning a lot. Question though. The pipe stay straight after the blending calve. If rad zone coming on won’t it get 55deg fairly quickly and the pipe stay triggers before the blending valve gets a chance to motor over. What speed ESBE actuator did you use?

[@Craiggilhomephe]

Great video szymon i was on the kimbo course with you about 3 years about (Craig from Newcastle) i am 100% in the same boat as you every job i price is always against installers who are fitting mixers and third party controls i also have a mounting collection for underfloor controls and mixers i have removed from systems on the heat pump side the manufacturer's need to ask more questions about what is going on to the system if vailant can sell 2/3 vdm's with there heat pump it's more money for them and lot better for the customer in efficiency

[@TheZippyMark]

I just wanted to say, your videos have definitely made me think more about my installs and what can be done to improve them. Quick question- how do you get these jobs? Like does someone request you make their heating system as efficient as possible? For my customers at least, I feel like making these sort of adaptations to a system would be a hard sell.

[@user-ju2mq6fp2e]

Another great video Where do you learned above this set up and technologies? Thanks for the great content

[@brendanfisher2528]

Great video. Sadly with the temp valve on UFH most customer or builders would just think your upselling or won't bother due to extra cost

[@deanchapple1]

Great video!! Thank you.

[@UrbanPlumbers]

You are welcome!

[@marcozorzi6770]

Great video 🔝

[@lemmykilmister450]

Great stuff as usual. But so many installers are afraid of adding cost and loosing the business. It's sad that so many customers aren't interested, they just want something that works as it did before.

[@Lutonfc88]

Brilliant video as always! I’m looking in to overlay UFH for my house. What company would you recommend?

[@smartboilercompany1983]

Top video as always 👍👍

[@dtek1832]

Great video, Just doing my research prior to selecting underfloor heating.... Would love to know your thoughts on connecting underfloor heating to a Valiant Ecotech combi boiler. Many thanks.

[@redchappy]

Love your videos, I've a viessmann 050 combi with ufh downstairs and rads upstairs, what set up and controls would you use ?

[@rhyme2192]

Thank you so much for this. I have two manifolds one downstairs and one upstairs and put it 10cm apart downstairs 16mm pipe and 14mm pipe upstairs (couldn't fit bigger pipes due to routing hitting existing electrical). This is without additional pumps, all on the CV which indeed electronically switches temperature so no mixing needed. The problem is that the rooms upstairs run too hot for our taste even with the 14mm size pipe. I run 32mm uponor to both manifolds, there are no radiators. I would like to add actuators upstairs only to maximize per room the heat it should have before shutting down. Plan to do this with small hysteresis (0.2). Would this setup also not be good for efficiency? And would I still need a bypass if I program it to always keep open 1/2 loops? Downstairs manifold is always open. Would waterside balancing of the manifold be a better alternative? I have tried but it is hard to say that bedrooms need to be 18c and workroom 20. I always thought balancing is to make sure return temp is even on all loops. Thank you so much for your videos, they inspired me beforehand to make the choices you said!

[@gracht24]

You know your stuff. I am getting a heat Airsource pump but the company are proposing leave my manifold setup for a combi, with a restrictive radiator type mixer - now I know whats required: A rotary mixer valve (maybe controlled by ASHP box) and a pipe stat

[@kenputer56]

We have been using Tekmar controls with injection setup for our infloor jobs.

[@tomplumb7754]

Nice video, hopefully you will push more Installers into fitting modulation controls.

[@UrbanPlumbers]

Ir was actually you Tom who told me about using ESBE on those set ups !

[@derekclark7545]

Been using this type of system in my house now for over nine years, not quite as sophisticated as the vaillant system as mixing valve cant be catered for on a Glowworm Systempro3, but by careful setup I have managed to use underfloor heating with no mixing/blending valve and fanned radiators upstairs that run on the same water temperature as underfloor heating with weather comp, there is overheat protection via a pipe stat wired back to the boiler, system is weather compensated so hot water priority and when called runs at max 73 degs until pocket thermister is satisfied then system switches back to UFH at any temperature up to 46 degs. Your correct in what you say though when it comes to heating installers living in the past, nobody wants to spend the time learning how to wire up these weather compensated systems, and yet the wiring is in fact very simple once you understand that the controls and sensors will look after the system, an example being you dont need a bypass, the system will shut down the burner, keep the pump running and leave the zone valve open for the required time to disapate the boilers heat. like all Vaillant/Glowworm boilers the thermistors are used to great effect to test, check and monitor the complete function of the boiler and system, also the maximum boiler size is dictated by the larger heat demand as in total heating demand or total hot water recovery demand so in most homes thats a 10KW maximum boiler and here is where Vaillants new boilers has an advantage, the 10vu, 15vu, and 20vu can all rate down to 3KW in weather compensation. I am really pleased to see that you are educating engineers to chuck the mixing valve away and control the UFH water temperture via weather compensation controls. There is so many advantages to this kind of install that you can achieve great comfort and fuel efficienty and better reliablity long term.

[@danielbailey1452]

Tell me your not a heating engineer without telling me your not a heating engineer 😂😂😂

[@derekclark7545]

@@danielbailey1452 The heating engineer is Urban plumber who I have followed for some time, his knowledge has grown and grown and I like his style in approaching the systems he works on, there are few really good engineers on here like Szymon for Urban plumbers, Andrew Millward and, Adam Chapman who I also like to follow, these guys are real heating engineers.

[@christianpratt]

Fascinating stuff! I have underfloor heating with a manual blend valve (and pump) on the manifold - the very thing you're keen to avoid. I also have an ASHP with weather compensation, which is controlled by a VR70 and is set to provide different flow temperatures for the UFH, DHW (valved to work in isolation of the heating, as you recommend) and radiators. When the heating alone is running, in lieu of removing the manual blend valve, should I simply open it fully (position 5, I think) or indeed close it fully? (And, on that basis, should I only ever run the UFH at different times to the radiators, given they have different set flow temperatures?) For reference, I see a manifold Flow temperature of c. 43 degrees and a return temperature (measured the downstream side of the manual blend valve) of between 32 and 35 degrees, depending on how many zones are active. Any guidance gratefully received! Thank you.

[@nmparmar]

Awesome content and really well explained. What room stats did you replace the Heatmiser stats with? Really interested in the detail of this setup. How are you switching the ufch pump and the setback temp timings? Do you perchance have a wiring diagram?

[@MrLucasg60]

maybe watch it again,having wc no need for rooms stats?He explained well whats been done and even i understand some :)

[@stephencharles1398]

The cowboy plumbers that installed my 6mtr x 6mtr extension u/floor heating did not put enough pipework under the screed/tiles, I have to run it flat out at 60°c to get the room up to a max of 19°c. Need to have a radiator put in now as well.

[@adydanner]

Hi brilliant video. Would you do a video whereby you go through each component and let us know makes models and where to obtain them. Example being finding underfloor boarding that takes 100mm centres, electronic mixing valves at manifolds etc. some items you can find with a Google search but some of the other components are not so easily found. Thanks. Ady.

[@sheermagic]

Great video. Wish you were on the isle of wight.

[@peterreeve8663]

I am a retire heating controls engineer that worked on building management systems. We occasionally did a system such as described in the video and would control in exactly the way described. If you keep the boiler flow temperature down to the minimum then it goes into condensing mode and you reap the benefits of efficiency. With regard to zone valves on the manifold I see your point as the system takes so long to react because the floor is a big storage radiator. The underfloor heating has got to be sized correctly and balanced and the control engineer has to be told the correct max flow temperature in the manifold. I always thought it was about 50C. You have not mentioned occupancy time or should it just run 24 hours.

[@UrbanPlumbers]

You run it 24/7 and use a set back flow temp for periods of lower or no occupancy

[@Jhhhf4479]

Some install microbore as it is sold in dry UFH kits. Handy for less intrusive retrofits snd upstairs. Are they are any dry models that incorporate 16 mm bore?

[@user-tm2gb7cj8k]

Thanks for explaining this, as a customer rather that an installer I feel much better placed to avoid being poorly advised. I think installers feel the commercial pressure to offer the cheapest upfront cost option, rather than the cheapest to run and most comfortable option. Meanwhile the customer does not understand there are potentially better solutions with marginally higher upfront costs, while in some cases, the same customer is spending freely on top end cars/kitchens etc but not knowing they are buying a sub optimal heating system. Assuming legislation does not help the customer, the only hope is education which to your credit you are providing

[@bigpete1986]

Spot on! The trouble is it’s never a level playing field as knowledge and competence in the industry is so vastly different.

[@gavonak2841]

Agree. 4-5 years ago when buying a new boiler and trying to solve a heating issue one installer quoted to convert me to S-Plan the other two did not include that. 12 KW difference in recommended boiler size between installers (the one offering the S-Plan was NOT the smallest boiler. I could not make sense of the answers I got when I asked the installer to explain their choices - so hard to know who to ask to quote and how much I could trust the sales pitch. Whilst I was procrastinating and waiting for summer before an install the old boiler gave up - needed to act fast so ended up taking the “safe and quick” route resulting in an oversized boiler ☹️. For the installer it must have been difficult to assess how much time it was worth investing to convince me to buy. @Urban Plumbers can a Worcester-Bosch Greenstar Cdi Classic 30KW benefit from a similar approach to that in the video? Edit: UrbanPlumber has answered a similar question elsewhere in the comments - essentially he does not work with these boilers so is not certain but he does suggest that generally they lack control.

[@user-tm2gb7cj8k]

It is so difficult, you could separate the designer from the installer but who has time for that when boiler breaks down, everyone would need the foresight to get their future heating needs designed just in case the boiler breaks down, just not going to happen. I do think the EPC should be replaced with a heat loss calculation then at least the owner of every house sold would be closer to understanding how to heat it

[@deanchapple1]

Thanks

[@grahamkneebone4742]

Great video, do you even need the pump on the underfloor manifold if there is one already in the gas boiler?

[@nevillethumbcatch5691]

In this install, yes as there's a header in-between the boiler and the manifold.

[@adriandarke5393]

Hi, ive had heatmiser controls on my ufh since it was installed 14yrs ago, i find them useful, but on the system you have there, is it a two storey building?. And assuming the bedrooms would need to be cooler at night, say 19-20deg how would you regulate the rooms differently?. We are a bungalow basically and i have the living areas 22-24degrees bedrooms 19-20. Great video, i like the principles of vaillant boiler controls, but cant understand why other brands dont utilise controls technology. I also dont understand with pwd pump control and gasvalve/combustion control on most boilers, load matching cant be successfully achieved?.

[@bobchana1207]

Hi, I am not a plumber but just really enjoy watching the videos and seeing your work. I do have a question. I have discussed with some plumbers about adding 'Weather compensation' to a Vaillant system but been told as the Boiler modulates there is no 'real' gain. What are you thoughts?

[@UrbanPlumbers]

There are big gains in efficiency, much better comfort, better control, lower running costs and much longer appliance lifespan.

[@piotrkrajewski9059]

Neatly explained although SB blending valve completety not needed if the heater itself sets the temperature for the floor heating, much cheaper plus much more robust and, the mostly important- a lot quicker responding, would be maunal mixing temperature valve with the setting of 38*C.

True. Its for when you combine (high temperature) radiators that you need a better mixing. I sort of need tvis system myself. I have a weird thermostat based regulation which I think is meant to just limit the temperature but the floor heating seems to go way too high. Also the floor heating is missing all the regulation that my radiators enjoy.

[@phildelfosse8085]

Would you advise your system for low temperature sources ? Such as solar support in winter to floor heating ? Or in this case the fixed thermostatic valve is a good option ? Thanks.

[@petersmith2650]

Great vid thank you for sharing. Who’s your preferred low temp UFH design company please?

[@miantamoorsaleem8287]

+1

[@civti]

+1

[@jacbisgood2221]

Great place to put an inverter, right in front of the boiler flap!😂 I'm doing a few of these at the moment, amazing how well it purs if you've got everything set up correctly. Tricky to learn first of all but Vaillant are generally great at support.

[@UrbanPlumbers]

Yes - this improves Vaillant systems so much. Sparky didn't care here, did he?

[@chrishampele181]

I'm pleased to report the sparky came back and moved the inverter to a more sensible location 🙂

[@anthonysalisbury6945]

What is brand / model is the electronic blender? Can you modulate the blend and is that controlled via the control centre? Which ufh system from what you have fitted have the best setup?

[@andyhodchild8]

I absolutely agree that people dont want to have to think about it and lack of awareness of weather compensation is crazy. I dont get it vr10 thermistors are the bestand yet people are fitting bimetallic with all the bad hysteresis. Then you get digital temperature in the controller and on phone app.

[@thequietroom3991]

Does this approach work for alternate boiler brands? I have actuator supplied ufh with one room stat and blend valve on 16mm circuit 2 zone circuit. What are my options.

[@ktmman3]

Does this setup provide hydraulic separation? Or would you need to run this setup with close coupled tee’s on a set up with just a primary pump,1 rad zone & PDHW??

[@hm250]

How would one fit weather compensation to an existing diesel boiler underfloor system? My manifold has a radiator type manual valve to control temp, should be simple enough to swap it out for a auto system?

[@Divine_Evil]

I have the same ESBE valve. Any tips on how to set it up and improve my efficiency... I have a pellet burner with a boiler (about 50liters) with 45-65C working temp range. I have smartified the boiler with a Shelly relay and can turn it on/off and schedule anything I like. Flue temps are around 100-120C Hot water, I get through a serpentine which steals heat from the system. Which needs me to plan when I can take showers and they need to be quick :D.

[@alexsmith9973]

I have basically the same setup before anything was changed, can anyone suggest what sort of cost it would be to make it like the end setup? Love the videos, always insightful even for a mere laymen.

[@chrishampele181]

Simon can provide you a quote I'm sure. I"m the customer. 2 days (1 plumbing, 1 wiring) plus the controls.

[@richardpacker7514]

Great video Szymon, quick question what would you recommend for a staged renovation i.e. we're living in as we go. Underfloor heating in timber suspended floors. I'm struggling to find a system that uses decent sized pipes. Is it possible to do one room at a time if each room is pretty big. Don't want to zone as on heat pump so want low flow temps and as you say let it self balance.

[@SimonThorntonVideo]

I'm looking to do this too. Just saw the profloor system which is made for 16mm pipes at 200mm spacings. Trying to figure out if that would be suitable

[@dubCanuck1]

So, how do you deal with actual zones where peopl want to have slightly different temps for each zone (garage, bathrooms, bedrooms)? Would you add zone valves back in?

[@Skeletoncrew46and2]

Quick question please. If your buying underfloor heating where do suggest the best provider is? You mentioned only one works off heat loss

[@LR52VUU]

In the process of installing UFH in a chilly 🥶 3 X bedroom ground floor flat. Could you please expand on all of the parts required to this? How does the customer control the heating in each individual room?

[@bimblinghill]

'The best part is no part' as the saying goes. As a heat pump installer I always rip out the UFH blending valves, but it'd be good to eliminate those silly little unreliable actuators too

[@brotherjohnno]

Could you do a video of the Kimbo pipe design sometime please.

[@goblinsgym]

Sadly, the heating installers I had to do with don't know how to set up boilers to minimize the number of cycles. With some reprogramming I was usually able to reduce the cycle count massively. If the boiler is sized properly to the house, and has a good modulation range, it can literally run through the heating season 24/7 at low power and high efficiency.

[@derekgoffin5807]

I have often wondered , in a house with some radiators and some underfloor like this property but with a heat pump, would it increase the scop to pump the radiators at faster flow then take the overwarm return water and feed it through maybe another pump in series to the underfloor rooms to return it really cold to the heat pump, with an automatic valve to bypass to return to parallel when really needed for maximum output?

[@TomPalacki]

Will there be vaillant vr wiring tutorial video? Regards

[@MrPaulpph]

fixed mixing for underfloor heating is also only possible with a semi constant boiler temperature. I have a solar system with buffer tank which varies between 55 degrees (from boiler, mininun) to 95°C when the sun shines a lot. Luckily my viessmann boiler can have up to 9 control circuits

[@liamcarr9756]

Good look setting the ebse I’ve struggled today Vaillant no Idea other

[@UrbanPlumbers]

It’s easy if you know how to read the manual

[@liamcarr9756]

Well yes Wired to r9/10 Set the valve open position And hoped that when the actuator moved it would move to blend The instructions are not exactly easy I’ve worked on commercial mixers And physically taken them off and moved it with the on off controls to set it where needed This however is difficult as there are no settings on installer level to manual make the actuator move one way or the other Any advice would be helpfull As not sure what to do other than put a fixed blending valve in Running out of time on the job etc Cheers Great videos helped me a lot to date

[@fluffy123987]

Hi Szymon, would this arrangement be suitable in a heat pump situation where you have a smaller section of UFH that you want to run at 35C max and the rest of the house on rads that might need 45 - 50C? Would it be possible to control from its own sensocomfort unit (lookong at an Areotherm Plus) for setting WC curve etc or would a VDM be better for native control? If being fed off the CH circuit (its pretty much other end of house from potential heat pump location) would some form of hydraulic separation be needed to sheild the CH from any impact of the UFH pump near the manifold?

[@UrbanPlumbers]

yes you can use this kind of set up on heat pumps. VDM I am not sure about what kVs vaule they are - much easier to just find correct ESBE vave - and probably cheaper too. You will need VR71 to do it added to the heat pump interface.

[@GdaySport]

Just moved into a house that has been fully refurbished including new boiler and radiators. I suspect my boiler is also wildly oversized because it is constantly cycling. Cant wait to get rid of it for heat pump...

[@Felix-st2ue]

There are probably a few things you could try first. Check the heat curve first. Most of the times it's way to high because the installer doesn't case about your Bill.

[@Liam_Hirst]

i dont do the wiring on my systems and im not sure i could find an electrician who would be clud up enough to wire the systems like this. are there any wiring diagrms anywhere for this type of setup

[@heatpump8566]

Have you got a wiring diagram for the mixer valve and pipe stat please.

[@Anthony-dh3ty]

Do you use proportional pressure setting on UFH pump with an esbe? I thought it was better to used the fixed temperature for UFH.. or is this only for a high temperature manifold?

[@johnc4323]

It's never "better" to use fixed temp to any space heating circuit. Pump setting will depend on system, if you have actuators the proportional, if you don't then it could be a fixed speed.

[@jedherman7450]

Is carpet for UFH with a HP a very bad idea? Thanks.

[@tonypotter5589]

Where are you based? I’ve just fitted the pipework and manifold from wunda ufh. Not get done the electronics and valves etc etc I need help please

[@Bobyslav]

Love your videos, especially this one! But I don't understand your point about not having individual thermostats and actuators for each room. How am I supposed to set my bedroom and bathroom to different temperatures with this setup? I feel like I'm missing something here.

[@mixer7586]

I'm not to sure also but im guessing pipe spacing, say 100mm centres for bathroom and 150mm in bedrooms along with increasing flow rate on manifold.

[@UrbanPlumbers]

Yes pipe spacing and flow rates allow you to design a perfectly balanced system

[@nigelsmith7955]

When the pipe stat shuts of the pump, can the boiler pump still circulate or do you have check valve in the pump? Nice conversation.

[@danielrose1392]

That's why he added the additional pipe shown at the beginning. It allows recirculation from the boiler output to the boiler input, in case no zone demands water. This path has much less resistance, so no water will be pushed through the loops if their pumps are off. Obivously this will shut off the boiler because it will quickly reach it's temperature, but that's exactly what we want when no one is demanding heat.

[@opentrail]

can an Ideal combi be controlled similar to a Vailiant? What UFH design company do you recommend then? I love your explanations.

[@UrbanPlumbers]

No, ideal is a very basic boiler to out it nicely

[@Liam_Hirst]

also which company would you recommend for underfloor supply thats designed to my heat losses

[@miantamoorsaleem8287]

+1

[@rowanballinger3690]

I’m currently doing a heat geek coarse but how do I learn these new systems Is there pipe and wiring schematics available? Been in heating for 20 years and build electronics circuits for hobby’s so I could get into this,

[@UrbanPlumbers]

You have to figure it out yourself I am afraid - that’s what I have done with help of other engineers. I will make some tutorials soon, promise!

[@tarlochankaliroy1030]

Could you do a wiring chart to see what the layout is in visual form rather than just oral?🙏

[@LocostR1]

You might glean some additional info from Andrew's video here of our own installation using the same controls and mixers on the same split UFH/rad 2 zone setup. kzbin.info/www/bejne/bYmYhYWVmpV9gK8si=Z4jGy9kVlslgXX7C

[@nmparmar]

@@LocostR1 very interesting. What room stat / controllers do you use?

[@LocostR1]

@@nmparmar We've got the SensoComfort VRC20f controller which is situated upstairs and linked to the upstairs radiator zone but it doesn't need to do a lot of temperature modulation, once the WC curves are set correctly the room temperature self regulates based on the target room temp / flow temp pretty accurately without needing a physical stat to control when it's turned up/down. Indeed on the downstairs UFH circuit we don't have any stat/controller at all, the UFH manifold runs without actuators and there's no room stat, it runs pure WC mode.

[@albertoporras04]

Not sure about not needing control valves on underfloor loops. I've just had an ASHP with full UFH (no radiators) installed and I was heavily involved in the design of the system, although a complete amateur with my only "training" coming from watching Heat Geek and your KZbin videos! Although the primary control of my system is by weather compensation varying the ASHP flow temp, I have a secondary control system consisting of room stats and control valves at the UFH manifold. The reason is that the ASHP/UFH is not the only source of heat in the house. For example, if we do a lot of cooking one evening, the kitchen/dining room will get a big boost of extra heat, if the UFH is left running in that room it would get too hot. The kitchen/dining room also has a lot of glazing, large windows on three sides and a very large glass lantern. On a cold but sunny day the solar heat gain is significant, again if the UFH were left running modulated only by the weather compensation curve the room would be over heated. The room stats are set just above the temp that the weather compensation is designed to provide so that if a room receives excess additional heat from another source then the UFH flow is stopped. Single zone pure weather compensation is very efficient, but is is also a bit of a blunt instrument, 2C outside air temp at night of on a very dull day with not much going on in the house can be very different too 2C outside air temp on a bright sunny day in a house with large south facing windows. Your views?

[@UrbanPlumbers]

Absolutely no need for additional controls. UFH when run on WC will not overheat your room even with cooking or solar gain. UFH with a surface temp of between 21-23c simply has no heat transfer happening once the air temp is close to the surface temp You are totally overthinking it! The beauty of properly done WC UFH is self regulation

[@pmbpmb5416]

Would it make a difference if you have a mix of underfloor heating and radiators , mine will be a new install so radiators should be sized correctly . Additionally should I be looking at 22mm pipe or is that going too far ?

[@albertoporras04]

​@@UrbanPlumbersVery good point! I could have saved quite a bit of money had I thought of that - you live and learn.

[@albertoporras04]

​@@UrbanPlumbers .....on the other hand.... 😊 My house is a small bungalow with a high heat loss, it has no wall cavities and has an L shape so large wall area, so we planned for relatively high floor temps in cold weather - to the extent that we went for porcelain tile flooring throughout rather than LVT to get around the 27C max floor temp of LVT. So we could get floor temps significantly above room air temps and would get heat transfer...., I think I feel better about my UFH valves now,... Your thoughts?

[@Felix-st2ue]

​@@albertoporras04 But if you have a lot of Extra heat in the property the return temperature should rise and the Heat pump should adopt to it no?

[@no1knows121]

Is it possible to control temperature output in a similar way on a Worcester Greenstar 35CDi Classic System Boiler?

[@UrbanPlumbers]

I don’t know. I don’t work on Worcester boilers - ideal and worcester are not really technically advanced at all in low temp heating.

[@no1knows121]

Thank you. It is possible, using an EMS-ESP board and Home Assistant, I have it all up and running with different flow temperatures for hot water/heating.

[@shuhel02]

a Vaillant VDM unit would simplify things even more.

[@Angel_VR18]

If the manifold has its own pump do you always need the Kimbo header to create hydraulic separation?

[@UrbanPlumbers]

Especially if then manifold has a pump you need separation