US Pro Air Hammer Chisel, Is It Any Good - Bergen

[@jkgv1740]

Just what I needed to know about the springs installation. Thank you!

[@eastcoastuk9705]

Martin you don’t need to u screw it to swop ends ,you Push the long end what holds the tool in an it falls out an same again to fit next bit. Enjoy your weekend👍

[@loneranger5928]

Good review Martin and your ingenuity on swapping the switch to fitt the air gun

[@SCOTTISHPREPPERVARIETYCHANNEL]

Clever repair good tool honest review I think small cut out on chisel for spot welds Good one martin

[@GHOOGLEMALE]

Good demo, good repair!

[@ANDY-we7mr]

Thanks Martin for sharing that i have been looking at them on ebay to remove some ball joint rivets

[@baldanddangerous1572]

nice bit of kit ,and great fix,all the best martin,stay safe .........dougie

[@butlersempire]

You too doug.

[@alandykes2519]

Great review Martin and fantastic fix 👍👍

[@butlersempire]

Thanks Alan

[@alanhodgson5975]

Top job Martin just goes to show different manufacturers use the same components keep up the good work 👍👍👍👍👍

[@melmorris134]

Thank you 😊

[@Firthy77]

Hi Martin, I also have the needle gun attachment that fits on mine, it would make light work of stripping paint back from decks etc without all the dust 👍

[@barbarawiddowson635]

Well done on the fix Martin.Lucky you had the other Hilka air rachet.

[@butlersempire]

Yes, I was lucky.

[@christopherneale13]

Brilliant pieces of kit martin working as a mechanic here in the uk i have the snap on blue poiny version brilliant for wheel bearings, ball joints and removing rear axel bushes you can get a hammer end be careful with the cheaper amazon and ebay chisel ends they dont last very long great video

[@butlersempire]

Thanks for sharing

[@alpinegeordie]

Hi Martin the v chisel is for spot welds and the last one it for cutting sheet metal as in sill and wing removal or cutting out rot :-) cheeers

[@butlersempire]

Thanks for that Bill, I didn't know.

[@alpinegeordie]

@@butlersempire my Pleasure mate, back in my youth and in the motortrade, cut/ chopped up a load of rotten bangers and replaced umpteen body panels with the air chisel, like you say a quick rattle with the help of the air chisel, will loosen the most stubborn friction fit part or rusty nut/bolt especially when it's in a place where heat can't be applied.... mind you a good rinse with WD 40 gets you out of most scrapes... do you know why it's called WD 40 ? I will give you the pleasure of googling it :-) Bill

[@petefroud5308]

A right result Martin .

[@petermoore4056]

You could 3d print a replacement trigger for the chisel! Let me know if you need a model to print.

[@butlersempire]

I did think of that. I do have a 3D printer but its still in the box lol

[@parrot3402]

@@butlersempire an alternative would be if you send me the broken one I could resin cast one with carbon fiber in the resin so supper strong. could do a test 3d printed verses resin cast?

[@normsmowers4758]

Good review and nice little fix 👍

[@mj-ls7qr8xp3n]

Great video

[@nellekerietveld1795]

Thank you this was very handy to me. I just bought one. But I would like to know, how to put on the air. I don't have that copper piece you have on the black thing 😅

[@butlersempire]

You'll need an adapter I think

[@themowerman]

Pleased you got it working again mate. Mine has been good as gold so far. I see the mower man has one now too. Hope all is good

[@butlersempire]

Yes Mick, i was lucky to have that old Hika one.

[@MrZimmaframe]

I didn't know "Hilka" tools like to hiker, but it must be a "hiker" now 🤣7:42

[@philipnewton7524]

A quick fix martin any tool to make the job easier is what we look for waiting for u start on the gold car P.S love the old truck you just done Phil from stoke

[@koshtie]

Hi Martin a man of your calibre you could fashion 1 of those triggers out of metal, it would never break then, though to be fair the trigger that broke looks like its got less plastic to it? than the old trigger you put on, ATB Wayne.

[@Megalocade]

Us pro tools are pretty good, i have the same air hammer though mine has a longer barrel for a harder hit, its very good and was an excellent starter tool for me when i was first getting into air tools, don't use it much now with having the Astro air hammer but its there as a back up, i have say us pro tools are pretty decent ive got a selection of impact guns from 1/4, 3/8 and 1/2" as well as a load of us pro impact sockets all of which are getting on 16 year old now used regularly and still holding up well especially the sockets usually they round out but not these, excellent tools 👍

[@roystheboy]

nice reveiw i would get on to us pro and ask them

[@butlersempire]

I couldn't find any details Roy.

[@Parknest]

Those air hammers are a useful piece of kit. I bought an Erbauer one from Screwfix and I wouldn't have been able to replace the rear wheel bearings on the BMW without it.

[@spanermantim]

The other chisels will cut sheet metal it's very handy.

[@69virgin1966]

I couldn't agree with you more. I'm on my second air hammer and I don't what I would do with out it.

[@Zephieish]

Time to finally break out the 3D printer.

[@davidvickers9029]

Not a bad price Martin

[@butlersempire]

Yes, Its cheap but effective Dave

[@zeez3139]

Pathetic that no one makes an aluminum trigger !

[@mikevp5303]

Would be nice if Martin can forge one from empty aluminum cans. It would be quite the process though