The rpm of drill press is too small for this. Work, so the finish is not as good as trimmer machine.
@gerardoherrera7041 Жыл бұрын
Muy interesante
@ak7198 Жыл бұрын
Нет , не нравится ! Устройство дрели не предназначено для боковых нагрузок вала на подшипник !... То есть , как ИДЕЯ САМОДЕЛКИ .....на другом конце Вселенной , где не слышали о фрезерах и в магазинах продаются только дрели - божественно ! А У НАС - Землян ...это - детский сад !)
@justomedel6633 Жыл бұрын
@@gerardoherrera70410:56 0:56
@finchworks795611 ай бұрын
As a teacher of industrial woodworking and tooling for 30 years, I find this use of a drill as a router with some skepticism. As the video shows, it IS possible. However, the 3-jaw drill chuck is designed to hold cylindrical tools working in the axial direction. Router chucks use collets for use with bits cutting with pressure on the radius. Using the drill chuck this way can result in the tool coming loose due to vibration. The lower rpm increases the chip load at the cutting edge, increasing vibration. Not really safe.
@Toni-oy5gu9 ай бұрын
As a drill press maybe, but not routing. Doesn't fit my safety protocols, I'm sorry.
@SamuelFonseca3936 ай бұрын
Pensei nisso também mas não de forma tão técnica, se percebe que a furadeira não foi feita pra cortes laterais, é mais tipo um quebra galho pra quem não tem uma fresadora.
@bargismathiasadv6 ай бұрын
Verdade
@user-ok9ey8ll3s6 ай бұрын
everything is correct
@incomer0128 ай бұрын
Мудевые страдания. Китайский фрезер за 2 тысячи сделает эту работу горазду лучше. А уж если нет двух тысяч на фрезер, то сначала надо идти учиться чему-либо и зарабатывать
@user-ld1qd5hs4v3 ай бұрын
Пусть займет в банке
@skepticskeptic Жыл бұрын
Дружище!!! Для шлифовки или зенковки, для разворачивания отверстий дрель, с ее 2800 потянет. А для фрезерования соррян, это безумно мало, дерево анизатропно и очень сильно, поэтому на малых оборотах, жа еще с 2-х заходными режущими кромками, материал будет подрывать на границе перехода свойств, от вдоль до поперек волокон. И можно пораниться, однако. Не зря же на фрезерах и кромочниках обороты высокие, именно по этой причине.
@SergeyChuiko8 ай бұрын
Да, зачем надо знать про фрезеровку дрелью то? Мало кто знает, что телефоном можно забивать гвозди ....
@edvaldosantana32955 ай бұрын
Vixi! Tú chutou o pau da barraca, hein!? Cara!
@user-lz2kr2yx4e11 ай бұрын
Для качественной обработки древесины фрезой у двигателя дрели не хватит оборотов
@TheAlexCave11 ай бұрын
"Право на жизнь" конечно имеет, но в реальности - это уж совсем "денрофекальный" вариант. При том (как не раз сказано тут в комментах) не только из-за скорости - она слишком низкая для такого мягкого материала, как древесина. Но и из-за того, что дрель по своему устройству НЕ рассчитана на боковую нагрузку. Я сам подобными "изысками" убил уже не один инструмент - сперва просто по глупости, позже из-за безвыходности (надо было срочняком, а подходящего инструмента не было под рукой). Так что это скорее : как сварганить фигню для производства полной фигни и убиения инструмента.
@user-sf4yu7jb9v Жыл бұрын
Ребята, не морочьте себе голову. Проще купить самый дешёвый кромочник за 2500 руб, чем работать таким инструментом. Это себя не уважать.
@user-qj4fv5uv4g8 ай бұрын
Это точно
@richardefriend11 ай бұрын
Given how inexpensive basic routers are today (I recently got a full sized one from Ryobi on sale for under $30), and how slow this 'device' spins in comparison to what's needed to do a decent job, you'd have to be stranded on a desert island (with unlimited fuel for your generator and an unlimited spare parts inventory) for this to make any sense at all. It's both clever and totally dumb at the same time.
@richardvedder77611 ай бұрын
Amen!!
@KenFullman11 ай бұрын
I have a spare router, so if I take the base plate off, I could use it as a substitute for the drill in this project. I'm so excited. I think this could work.
@peethreeorion11 ай бұрын
That's some pro-level sarcasm, folks!@@KenFullman
@eggsngritstn9 ай бұрын
Yes, my thinking exactly.
@saaamyk9 ай бұрын
bro spent more than $30 in parts if he bought them
@user-wk6wh6bj9x Жыл бұрын
Отберите у него уже весь электроинструмент, пока человек не покалечился. Или он уже киборг на половину. Хотя дуракам законы физики не писаны)))
@ProminiVik6 ай бұрын
полнейшая ерунда,на мой взгляд
@Qykizassss5 ай бұрын
Этот человек показывает, что может ещё кто-нибудь покажет более лучшие варианты, люди на канале есть может только начинающиеся и уже хотят показать, чтобы может глядишь и подскажет!🇰🇿🙂
@claudecisilva6483 Жыл бұрын
Obrigado pelo projeto, desde Brasil.
@Mixa007Master11 ай бұрын
4 отверстия в большом кругляке и можно к столу прикрутить кверху фрезой и так же поднимать и опускать ну и читаем комменты ниже про количество оборотов для работы с деревом.
@Thesnowiswhite Жыл бұрын
Приветствую! 👍 Когда то я хотел начать страдать подобным. Но всё же купил фрезер. Дрель не годится для этого. Очень низкие обороты у дрели.
@bloborsghost8167 Жыл бұрын
Это не функция дрели, а приспособа для неё. Дрель осталась со своими функциями - сверлить, вкручивать - откручивать. И стоило заморачиваться чтобы сныть с дервяхи фаску? Есть рубанок или лучше лобзик с подошвой установленной под 45*.
@farhmak16046911 ай бұрын
Я понимаю всю банановость нашей жизни, но если нужен фрейзер, то лучше его купить. Хотя-бы чудо-юдо, фиолент😂
@user-nq6jh4xg8m Жыл бұрын
жесткость конструкции зашкаливает _))))
@nailabc230311 ай бұрын
Глупое изобретение !!! ...........Обороты дрели около 7000 оборотов в минуту, в то время, как фрезер дает до 25-30 тысяч. Эта разница сказывается на качестве реза. Кроме этого, нецелевые нагрузки сильно убивают редуктор дрели
@michaelhanrahan534911 ай бұрын
Do all drills have this function, or is it just certain types of drill?
@dharmanisuwandiwandi212811 ай бұрын
Wow...great idea👍👍👍 thank you for sharing..I must tray this skill..🙏
@dioxhg Жыл бұрын
каменное зубило уже было? секрет каменного зубила в студию!
@neliorodrigues2249 Жыл бұрын
Muito bacana ficou excelente o projeto furadeira/fresa ferramenta muito útil foi uma ótima apresentação e muito boa à demonstração valeu obrigadao obrigado
@ThisIsAMyAccount Жыл бұрын
Канал следовало бы переименовать в «Как довести инструктора по ТБ до инфаркта». Кто хочет покалечиться - обязательно повторяйте эти «изобретения».
@RaymondDriggers-zp4xd11 ай бұрын
I live in America so I could pick One up while you are spending your free time building one of these! Really enjoyed the bluegrass music!
@Suhail_AlIraqi Жыл бұрын
فكرةٌ ممتازة وغير مُكلفة ، أحسنت
@user-ey1eq4ch4j11 ай бұрын
Нет у дрели такой функции - кромки формировать. Это функция фрезы, которую пристроили к низкооборотному инструменту. Не самая удачная конструкция, к слову.
@1970Pitbull Жыл бұрын
Блин, я пьянь болотная, почти не просыхаю и то фрезер есть.
@user-rp7cg8sp3g11 ай бұрын
Маловато оборотов.
@Shurimanov10 ай бұрын
😂 Привет брат т,
@user-me6uq8kh7y11 ай бұрын
Сравните мощность, скорость оборотов, точность и надежность фрезера и этой самоделки...не стоит портить дорогой материал и тратить свое время и нервы понапрасну
@anbu.sequat945511 ай бұрын
Cerdas dan kreatif min. Cuma kalau kita pakek mesin profil lebih ringan dan gk ribet😭😭😭
@user-pi3lh1ih2k6 ай бұрын
Круглое носим, квадратное катаем, ну как обычно, из болгарки делаем косу, пилу но не по прямому назначению
@dankrzy476911 ай бұрын
I tak wynalazł frezarkę. Wow!
@andrewlowe91307 ай бұрын
There's an amazing tool that was invented a few years ago... I think it's called a router 😮
@robertwilson20076 ай бұрын
There is also a drill attachment called a A Portable Drill Guide that you can buy and drill at any angle you like and I would think you could insert a router bit onto it and get the same result as a router without buying a router. 😂😂 P.S. The Portable Drill Guide can also be used a as small drill press. 😂😂
@vaccavo11 ай бұрын
Obrigada!
@user-tm8mm1wx7o4 ай бұрын
Выбрасываю фрезер. Пойду дрель покупать.
@Cahsolotree6 ай бұрын
Kreatif dan menginspirasi,terima kasih
@apenza430410 ай бұрын
Save time and money by buying the right tool for the job. They’re called drills because they are designed to drill holes unlike routers that are designed to shape and make grooves in wood.
@gregorall97798 ай бұрын
Yeah....it makes so much sense to spend 2 hours putting all this together, not to mention the cost of all the parts, than to simply use a router.
@budiasakadek3342 Жыл бұрын
Bagus. Tapi mending beli alatnya satu set. Lebih murah dari harga bornya😂😂😂👍👍👍
@rwakomaerickriecy29679 ай бұрын
Amazing 👏 thank you for sharing
@SubramaniamLakshminarayanan9 ай бұрын
Few people know about this function DRILLS ! - The fewer people that know this function, the better for the world!
@its_marc8 ай бұрын
If only there was a pre-made tool to use those router bits in
@user-us5cw3eq8y8 ай бұрын
😂Мало кто знает, что фрезером можно сверлить🤣
@hanssigmund890310 ай бұрын
Das ist kein Bohrer sondern ein Fräser. Ein Holz-)Fräser benötigt zudem eine sehr hohe Drehzahl, weshalb eine Bohrmaschineals Antrieb ungeeignet ist.
@konsatntinchernov4779 ай бұрын
Можно и плоскогубцами гвозди забивать🙂
@douglasflores146211 ай бұрын
Good idea, but any drill doesnt have the RPM (the speed) necessary for a drill bit to work properly, and nowadays, a router is cheaper than before.
@jimclark62568 ай бұрын
It's a router bit not drill bit but you are correct about the rpm's.
@user-vp4gb1db9v11 ай бұрын
Оцените заказчики,кто и как выполнит Ваш заказ,быстро,качественно и недорого 🤣🤣🤣
@1parky210 ай бұрын
Drill chucks are not meant to take side loads. Using it as a router is not a good idea.
@user-tv7qn4tt2j Жыл бұрын
That's useful idea.
@moesliman3004 Жыл бұрын
Ideu kreatif, cemerlang!!
@Cahsolotree9 ай бұрын
Kreatif sekali dan menginspirasi.
@birdolla444110 ай бұрын
This is the equivalent of putting a lawnmower engine in a Ferrari.
@julio276811 ай бұрын
Ai manja , Ai tem os dons, Ai tem sabedoria
@user-yb6oo1yd3v Жыл бұрын
Че курил😂
@TukangInterior10 ай бұрын
Ide yang bagus dan kreatif 🇮🇩🇮🇩🇮🇩
@NemoO456711 ай бұрын
такую фаску за три взмаха рубанком сниму,это шляпа братан))
@ramonhernandezperez2165 Жыл бұрын
Faltan tus medidas de los materiales por qué no las pone.gracisd
@eswift831810 ай бұрын
Good lord. You can get a trim router for $30. You've already spent like ten bucks on hardware for that rig. It will be safer, and cut better.
@diret520511 ай бұрын
О вернёт мне 6 минут жизни😮
@anapaulanika742111 ай бұрын
Muito legal 👌🏼👍🏼👍🏼👍🏼
@user-tn4pf9du7k9 ай бұрын
Ты сам когда нибудь работал с таким инструментом?
@stevec25139 ай бұрын
Holy crap. But a $90 router at the big box store.
@michaelburkhart8767 Жыл бұрын
This is why we need a functional "Thumbs Down" button: Wafer board will not hold up to the stresses and torque that the drill generates, especially if it hits a knot in the workpiece. I can easily imagine it exploding into several pieces. This thing is stupid dangerous. If an employee walks into my shop with one of these, I would immediately confiscate and destroy it, and fire him on the spot. The depth control provided by the bolt lacks the precision that proper routing needs, plus it looks like the bolt would interfere with the drill housing if you're doing deep cuts. The handle by the chuck is the wrong place to hold a router. If the bit hits a knot or experiences blow-out, the resulting torque could send the whole machine flying out of your hand. And then there's the cost: sure, this was made by scrap wood pieces, a couple drawer slides, and other parts, but your time is also worth something. Buying a proper router would probably be cheaper than the hourly wages it took to make this hack, and it would be a better tool.
@mjccote94819 ай бұрын
Hi is someone knows the tune of the fiddle and mandoline ? Very nice video
@fil223299 ай бұрын
1. У дрели одна ФУНКЦИЯ - СВЕРЛИТЬ. 2. Изобрел ФРЕЗЕР. Пора бы и велосипед изобрести. Называется: когда коту делать нечего...
@faithful45111 ай бұрын
Sorry I'd never do this. In my country you can find a cheap electric trimmer/router that would cost not much more than the time and materials for building this jig, plus it would perform way better, and you wouldn't have to worry about burning out your drill which is not designed for continuous running like this. Unless for some reason you have multiple free electric drills lying around...this is not a good looking hack.
@kamarudinbinhanipah79182 ай бұрын
Only for that purpose? Just use a sand paper😂😂😂
@Yurydan626 ай бұрын
Если уж хочется такое делать, то делать нужно всё же из прочной толстой фанеры, а не из ЛДСП. А лучше всё же купить простой фрезер. И более точный механизм, и обороты выше, и функционал шире.
@cesarmendes4485 Жыл бұрын
Mas para isso já existe a tupia. 😮
@jolox. Жыл бұрын
Great music!
@GP-pw5wb8 ай бұрын
Is it worth the bother? Apart from the fact it won't do any real work with accuracy i would consider it a tool likely to cause serious injury.
@Trutko.Dmitry Жыл бұрын
Обороты вращения дрели и фрезера - немного отличаются, всего в 4 (четыре) раза. Годно только для черновой обработки. Но единственное преимущество - дешевизна.
@Thesnowiswhite Жыл бұрын
2000ˣ4=30000? )) В 15 раз выше. )
@user-zt3td5ux1s Жыл бұрын
@@Thesnowiswhite коллекторные моторы переменного тока на 15-17 работают
@Thesnowiswhite Жыл бұрын
@@user-zt3td5ux1s 15-17 это тысяч оборотов в минуту? Да есть и 30+ коллекторные. Суть то что у большинства дрелей меньше 1000. А потолок 2100. Больше не делают. Есть конечно исключения где 4000. Но такие в СССР были в наборах. Сейчас подобных в продаже и не встречал.
@user-zt3td5ux1s Жыл бұрын
@@Thesnowiswhite наверно автору стоило еще пару редукторов прилепить от сгоревшей болгарки, пилы, лобзика итд...для полноты диайвая
@user-zt3td5ux1s Жыл бұрын
@@Thesnowiswhite я использую совецкую дрель для фрезеровальных задач...но у меня направляющая из швеллера на верстаке стоит и к ней я креплю самодельные приспособы с болгарками, ленточными пилами, дрелями...но задачи грубые для дерева...хотя восновном камень, плиты швп фрезеровал
@jozefovadielna8 ай бұрын
The tool also has a specified number of revolutions per minute from the manufacturer. The drill will never reach such revolutions.
@user-bc2mm6hb5o2 ай бұрын
Федот, да не тот! Тут обороты нужны! Тысяч двадцать примерно. Человек на эту работу потратить время, а затем будет очень обескуражен некачественной обработкой детали.
@nuralsingkutichannel70799 ай бұрын
Mantap idenya
@felixmadison573611 ай бұрын
It's no secret now, but I don't think it will catch on. There's something called a 'router' that does an even better job, and you don't have to build it yourself!
@ivanalfonsocorderogutierre749810 ай бұрын
Thanks!🎉
@marcelobatista98395 ай бұрын
Belo projeto. Aqui no Brasil, se diz que quem não tem cão caça com gato. Marcelo - Brasil
@thantran68769 ай бұрын
Wasn’t showing full details how to measure all materials.
@carlysechs5 ай бұрын
Das ist eine Sache der Genauigkeit. Bei dieser Vorrichtung reicht es vielleicht zum Bau von Kanickelställen aus.
@piotrnapieraa5422 Жыл бұрын
Super 👍👍👍
@Erniethebear3 ай бұрын
KZbin Shorts: Where dumb ideas breed like rabbits.
@reklaamipunkt9 ай бұрын
Музыка классная !
@yardlimit869511 ай бұрын
if you have anymore secrets like this one, PLEASE KEEP THEM TO YOURSELF
@user-fm4jl6us4f3 ай бұрын
Обороты должны быть раз в 20-25 больше. Не морось яйца ,купи фрезер по дереву.😂😂😂
@user-fm2ld2mm2n Жыл бұрын
Сделать хреновый фрезер из хреновой дрели можно. Но не нужно. Самый простенький китайский фрезер будет стоить столько же, сколько и дрель. Удобные настройки, удобная замена фрез, микроподстройка глубины, копировальные втулки, параллельный упор с функцией циркуля и, главное, 25000 оборотов, а не 4500 как у дрели. В данном случае весь этот геморрой не окупается. Вообще такое впечатление, что видео создано с целью провокации хейтеров. Это ж сколько отзывов, хоть и ругательных...
@volkerlobel3406 ай бұрын
In Germany we call this an "Oberfräse" and here you can buy it for cheap money....
@marcusviniciusdeoliveirami2462 Жыл бұрын
Bom dia; um abraço
@greghillyer81959 ай бұрын
I just bought a router instead. That way my drill isn’t tied up.
@twinwankel Жыл бұрын
Very cool hack. You used some cheap particle board, drawer slides and other spare parts laying around to hack out a router. Of course the router bits were not hacked out. If you did, it would be an exceptional hack. Thanks.
@Yurydan626 ай бұрын
У нас говорят так: из говна и палок... (We say this: made of shit and sticks...)
@kurtseverinsen716 Жыл бұрын
A decent router costs around USD 100. It will provide the speed needed as well as a few standard bits normally. This is a very complicated way to save USD 100 and end up with a very inferior solution.
@user-ky7yf8hn9l9 ай бұрын
Для забора пойдёт!
@Paul-hp3fw4 ай бұрын
Музука просто жесть😂он бы еще полонез огинского врубил.Или черное море священный байкал
@AusMiner9 ай бұрын
An accident waiting to happen. Some people simply have no idea on how electric tools are designed and meant to be used.
@salomonhernandez32899 ай бұрын
Para que el aglomerado circular? No es buena idea, es una ideotas!😂😂
@antoniolazaro37953 ай бұрын
Ficou show mais faltou uma régua limitadora
@Igorechek4255 ай бұрын
На фрезе 30 000 оборотов, дрель около 3000. Чувствуете разницу? "Кёльнер" недорогой 2500 стоит в 2022-2024 году, а то и меньше. Для непродолжительных работ подойдет.
@pamukjanos97929 ай бұрын
Ivàn, mièrt nem veszel egy rendes felsőmarót?
@mr.e8432 Жыл бұрын
I’m guessing most people don’t know about this function of a drill… because it’s not actually a function of a drill.
@guillermocastilla1884 Жыл бұрын
Muy interesante 👍🏽
@billburgess910011 ай бұрын
Good video except for the bone crushing background music.