Using Reverb on the Behringer XR18

[@1800nodavid]

Never thought about feeding a delay into a reverb like that, I'll try that next time! Thanks

[@fusionsoundproductions]

It sounds good. I am going to try it too

[@KimIssac-g7w]

I just got my hands on cq18t from A&H. Hope you could do a lecture on it, esp xfs since they only provide handful. Always grateful for your contents! Really helpful!

[@adventureseeker423]

Loving these XAir specific videos!!! Keep it up!!

[@realbingus]

Thanks for this video, also very useful for our Midas M32. Knew some stuff, but learned a lot too :)

[@DavidMend18]

Thank You for doing this video

[@UrMusicConceptz1]

Thank you Drew

[@ChheatChhiv-zm3ei]

Hello sir I would like to teach from start to end for mixing vocal. Midas MR18

[@TheJesusrep]

Hey Drew! I asked about the supper rack performer. I wanted to know if there’s a way you have found to apply it on the LR on the XR18?

[@jeromes2240]

Hi Drew, Just a small question. When clicking the FX1 on the right (if I need to EQ it for example) there is a "master" fader on the right. Should it always stay on 0Db ? If yes, what's the use of it. We basically have three faders : channel send, channel return and FXbus master. In what context should we change the master fader ? I hope I'm clear enough. Thanks for your great videos 😊 Jay

[@DavidMoonWainwright]

I'd love some comparisons of hardware controllers with the XAir series

[@MKMTTG]

can you do a videi about Virtual soundcheck mixing on Behringer X Air 18.

[@kristenm3644]

Hey drew! Did they discontinue the iPad app? Or have there only been third party apps.

[@leee79]

Hey Drew Thanks for the video. I have a question. I have 7 vocals(1 lead and 6 back), which are fed to Hall reverb FX1 return. I have the FX going to the main LR, but not to any of buses.. All the vocals have wireless IEM setup and 3 floor monitors that are daisy chained. So Bus1 is for the lead, Bus2 is for the vocal 1 and so on, and Bus8 is for the floor monitor. Vocals want FX to be fed into their IEMs and when I feed the FX1 to a particular vocal’s IEM, FX return from all of the vocals go to that vocal’s IEM as well. Is there any way I can just feed just that vocal’s FX to that IEM? I am using Midas 32. Thank you.

[@djameleddinefenni3148]

Is it possible to have a set of fx différents for every aux output Example Aux 1 : only snare has reverb Aux 2 : only vocals have delay Aux 3 : only bas has compression Etc etc

[@donaldburns4462]

This is a little off-topic, but I need help with saving a scene to a usb drive for safekeeping on the wing.

[@kevinrodriguez3093]

Hello, I bought a brand new XR18. Once I connected to it and tried to set up the latest firmware. All my channels are showing max signal levels. And no sound comes in or out of the mixer. Factory rest and loading different scenes. And even tried intializing the mixer and no change. Seems like it's locked up. Any ideas or solutions for this?

[@ManuelF-c6y]

I have the x air16 Can not get the effects to be controlled by the effect faders

[@alan93]

the most confusing thing about that interface is how to get an effect on just one channel. I literally spend an hour trying to figure out how to not get delay on every channel and just put it on one vocal channel. did you explain that?

[@kelvinpell4571]

This is incredibly complicated. Is there any content creator out there who can just say....move this slider......click this button.....rather than using jargon. I have done this as far as I can, step by step , but it simply does not work. Is there a step that is missing at the beginning?