All you need to about fitting Vag 2.0 Tdi cr actuators
Пікірлер: 58
@jamesSmith-bn3ud3 жыл бұрын
Now this is a lad that ,,, KNOWS WHAT HE IS TALKING ABOUT ,,, i wonder how many garages would give the ,,,, IT A FAULTY TURBO CHARGER,,, ripp off ,,, well done lad for your honesty and knowledge,,, theres few like you 👏
@VWBUST2ED10 ай бұрын
Thank you, this was a great help. VW specialist couldn't help so I went ahead and did it myself. Safety pin bent straight to get the voltage and a £13 Mityvac copy of ebay. Used an old bike 10mm thin spanner and bent it to fit and sawed the ends so it would turn in the limited space. I am now struggling with ABS Operation 01130 008 implausible signal. But this I don't think is related. Although occurred within a week of Turbo and accuator replacement. Top videos post some more up. Thanks again
@johnk34272 жыл бұрын
Absolutely brilliant. I'm in Aus but if I was local to you I'd be on the phone right now asking to book my CC booked in. It has a problem with what I'm pretty certain is boost pressure but beyond that I'd prefer to leave it to someone, that is obviously all across this stuff, such as yourself .
@gall496112 жыл бұрын
Soon to fit a new actuator to my Tiguan 2010 TDI, happy with fitting one but was confused about set up…..until stumbling across this vid, absolutely brilliant and well explained, feeling so much more confident now. Great work, super humble bloke 👌
@mrjamook4 жыл бұрын
Can’t tell you how helpful this video was!! Saved me buying a whole new turbo and shelling out for 5 hours labour to have it fitted!!
@alexcovaci248 ай бұрын
Hi, can I ask you what codes did you had? I tried many garages and they said is full turbo… but the car pulls sometimes and I believe is from this actuator. I have P0299
@mrjamook8 ай бұрын
@alexcovaci24 in all honesty, I took a guess. The turbo was not smoking, and the core was solid when I tried to move it and the engine was absolutely fine... if its pulls sometimes then my guess woukd be the actuator. Did that job 3 years ago and the car still pulls great with the original turbo and 148,000 miles
@alexcovaci248 ай бұрын
@@mrjamook thanks for replying. I will order the actuator, calibrating it and I leave a comment after 🙋🏻♂️
@danielwarner1736 Жыл бұрын
Quick comment to say I really appreciate this video and it helped me out , thanks
@MRDLR Жыл бұрын
Glad to hear it!
@hafysharif55592 жыл бұрын
Hi Dom A massive thanks for the video after watching I done on my Audi A1 CAYC 1.6 diesel engine, been going round in circles for weeks with issue after changing the engine, because of your video mines is fixed, it was reading 1.76 volts, i done with Multimeter and miti vac. Thanks again
@stevebennett70942 жыл бұрын
Hi hafy , did you do exactly as dom did and set it to 0.4 v ? Having same issue lol cheers in advanced
@hafysharif55592 жыл бұрын
@@stevebennett7094 yes
@MRDLR Жыл бұрын
Glad to be of help, i now have a bit more free time at work so ive just finished filming the next video 😄
@Liveforeever Жыл бұрын
@@hafysharif5559 I've got the same problem with p256300 and P00AF00 after changing engine, turbo was fine before? How can actuator get damaged or voltage out of spec?
@alexcovaci248 ай бұрын
@@Liveforeeverdid you fix this problem as I got the same issue…
@khalidmalik11573 жыл бұрын
Very easy & simpl explained great job... Thnx, A*****
@colin50643 жыл бұрын
Excellent advice very helpful thank you for sharing your knowledge and experience on this topic
@ianjamesteper28262 жыл бұрын
Thank you very much for the video followed to the letter and great Results
@pauldaly39522 жыл бұрын
Many thanks for making and sharing this video would underboost code for a4 2.0ltdi ultra along with limp mode be also caused by dodgy actuator i replaced boost sensor and car continues to go into limp mode thanks.
@adrianrobinson32338 ай бұрын
Mine was a wiring short by the gearbox
@elvis8burgers81 Жыл бұрын
Really good vid, Dom, perfect show & tell here. My Mk6 GTD goes in for a new TA fit next week - local workshop - I just hope they know about the 0.4 V target! Cheers!
@MRDLR Жыл бұрын
great car! Glad to be of help, i now have a bit more free time at work so ive just finished filming the next video 😄
@ladislavtulia5430 Жыл бұрын
Where is you garage mate I have problems with limp mode
@spandauer9355Ай бұрын
hello, why 0.4 volts? The instructions always say 0.76 volts (vcds). Or is the voltage at the plug different?
@goulgr14 күн бұрын
My actuator is a different set up vaccum pulls rod upwards doesn't have 2 nuts on it either has small adjusting screw on turbo is it the same 0.4v? I'm getting 5.56v ignition off.
@TheWilltraff Жыл бұрын
Having issue with audi a4 2008 2.0tdi ... get a boost control poistion range perforamce fault.. ive noticed the fault is only beging triggered when vehicle is idling, no loss of power, do you no what voltage i should be reading with car ticking over ?
@keithloynes7161 Жыл бұрын
What a lifesaver thanks!!
@MRDLR Жыл бұрын
Glad it helped!
@keithloynes7161 Жыл бұрын
It worked for about 20 miles lol
@leebutler12982 жыл бұрын
Thankyou for teaching me something in 5min that probably took you years and years should be more lads like you on this planet your credit to yourself pal all the best...thanking you very much👌. Just wondered with you setting it at 0.4 does it make a difference if its a tiny bit above 0.4 or below 0.4 and if so what would give a better response if you get my meaning...thankyou
@AMtechEngineeringYT11 ай бұрын
Does anyone know the Part number or a link to the "Lock Clip" for the actuator nuts? My lower nut came loose and worked its way all the way off the actuator rod!
@gordonharper28693 жыл бұрын
Great video
@davidcostella5245 Жыл бұрын
My turbo was refurbished 2 months ago and now I am getting lo boost flashing coil light and engine management on I don't no if my acyfatter needs set up any ideas please thanks
@ladislavtulia5430 Жыл бұрын
Hi mate I have cc 2.0tdi dsg 2013 have problem with limp mode wen there car is cold but wen the car get hot it okay no limp mode wold you look at this if I com down mate please
@nikolablagojevic1785 Жыл бұрын
I got this on my 3.0tdi, (p00af) any ideas? Goes in to limp mode… restart the car and it runs fine
@djrix64602 жыл бұрын
I have a 2011 Passat 2.0tdi, the actuator arm isn’t threaded. Trying to use vcds to do basic settings on actuator however it fails. I’m guessing it’s because the voltage reading aren’t within spec. How do I know what they should be? Should I use a vacuum pump and do as your video?
@stefanogizzler3 жыл бұрын
Got the same problem on VW Golf 2.0l TDI, changed the turbo actuator and the mechanic said he couldn't clear the fault, now I believe he did not set it properly it reads 3.45V ignition on engine not started and 1.79V when engine is running on idle, I compared that to my other same VW that's working fine and was different, it read 3.45V ignition on engine not started and 0.79 engine running on idle, Any help I'd appreciate, Thank you so much.
@marksmith86634 жыл бұрын
I’m not a Mechanic I’ve got Same problem on 2.0tdi done a vacuum test on turbo actuator and Won’t hold vacuum. The the bolt on the arm is v hard to reach because I’m unable to lower it , with the vacuum pump because it’s faulty 😤
@robthesultan3 жыл бұрын
Any help with a tdi v6 electronic actuator would be great don’t have the Vw tools to to set it up any work arounds 🤔
@musclefox2232 жыл бұрын
Hi I have a Audi A3 2.0 TDI on a 2005 plate, it started to go into limp mode when I accelerated, this was at 135k miles and when I pulled over turned off the engine and re started it it would be ok, this went on for a while and my garage fitted a new turbo which has now done 15k miles and the problem has come back, garage has put some turbo cleaner in and says it should help but this hasn't worked before, can you advice please...Thank you..
@JayLillico Жыл бұрын
Would it still need calibrating through vcds after doing this?
@adrianrobinson3233 Жыл бұрын
Hi great video you did say that you occasionally give advise so my 2014 Passat 2lt tdi has the glow plug lights coming on with a code of p23800 I have changed the turbo switch but still the same, it will produce vacuum for about 30 seconds with no light open and as soon as the light comes on the vacuum goes. however if I pump up the actuator the light stays off totally any ideas
@MRDLR Жыл бұрын
Sorry i missed this comment i hope you got sorted
@alexcovaci248 ай бұрын
Same problem as above, what was the problem? Can you tell how been fixed? TIA
@wherescorbin953226 күн бұрын
Not being funny but if you get this wrong you shouldn’t be touching a car it’s one of easiest things I’ve done and got it 💯 first time I’m no mechanic
@jasonchilds62334 жыл бұрын
I’m having the same problem with my 2008 2.0 tdi Where are you based?
@GenXUndercover Жыл бұрын
Can someone help me before i looose my mind😂 Turbo/Super Charger Boost System P2263 00 [172] - Performance MIL ON - Intermittent - Confirmed - Tested Since Memory Clear Freeze Frame: Fault Status: 00000001 Fault Priority: 2 Fault Frequency: 14 Mileage: 121637 km Date: 2022.09.22 Time: 14:33:36 Engine RPM: 1112.50 /min Normed load value: 12.2 % Vehicle speed: 0 km/h Coolant temperature: 50 °C Intake air temperature: 42 °C Ambient air pressure: 970 mbar Voltage terminal 30: 12.038 V Unlearning counter according OBD: 40 Charge pressure actuator: specified position: 140.00 % Bypass valve f high press turboch turbine inlet: actual value: 103.28 % Charge pressure actuator: adaptation for lower stop: 4392.8 mV Bypass valve for high press turbocharger turbine inlet: status-Bits 0-7: 0 Bypass valve for high press turbocharger turbine inlet: status-Bits 0-7: 55 Bypass valve for high press turbocharger turbine inlet: status-Bits 0-7: 0 Bypass valve for high press turbocharger turbine inlet: status-Bits 0-7: 0 Bypass valve for high press turboch turbine inlet: uncond volt: 4500.4 mV Charge air pressure: actual value: 969.30 hPa
@dpov743 жыл бұрын
Tried everything mine saying 5 volts all the time regardless any ideas guys
@Liveforeever Жыл бұрын
Did you find the fault?
@patvill Жыл бұрын
Dom, I’ve done this by adjusting the top and bottom nut within range 3.5v (no vac) / 0.4v (w/vac). When I turn the key on its stuck @ 3.5v as seen on my short video kzbin.infowRMWxZogCHE?feature=share I swapped an N75 from my Transporter 2.0 CR and the value is still stuck @ 3.5v. Can you advise on what next step I can do ?
@GodsGiftToMom3 жыл бұрын
Where are you based
@MRDLR Жыл бұрын
Hi Lee where in Ramsbottom, Bury Manchester
@ghettogeniusno1 Жыл бұрын
wat town u based
@MRDLR Жыл бұрын
Ramsbottom Bury
@Hocuspocus2718 Жыл бұрын
I have set my new actuator up as per your video but flashing coil light still comes back on and dpf fault code is the only code there. I have cleaned the dpf on the car and theres no blockage. What am i doing wrong please as car still in limp mode