Step By Step iPhone Sandwich Reball Tutorial. The Best Technique For Reballing The 2 Layers.

[@VCCBoardRepairs]

What's the biggest issue you have when reballing sandwich boards? 👇👇👇

[@miguelmacke7360]

To dry or to wet solder paste 😂

[@ayoolanajeem]

Some line join together and sometimes some part are missing, gray out

[@Rammi08523]

often the paste stucks in the stencil and not at the board when i lift it up, why?

[@Halders1982]

Oxidised pads 😩

[@rayanajanane9912]

Make a video on oxidized pads

[@ExzeroX]

I have been using the Mijing Z20pro sires for years and years now, It's the goat for reball at the moment. When it comes to paste, I usually use something like Chipquick and I use both the low melt and 183 from them, It works great, and I can get a safe and reliable data sheet with all the chemicals and hazards. Biggest issues I have when reballing is when the bottom board is bent super bad. It just doesn't want to sit in the reball jig flat.

[@bobby9568]

This is why we subscribed

[@VCCBoardRepairs]

Thank you! Appreciate the support!

[@epp1733]

Hey Jesse, could you upload a video of remaking the oxidized and broken pads. Also how much pads is the maximum to remake ? Greetings from Greece my friend

[@VCCBoardRepairs]

Ok great. I'll see if i can make a video on it

[@Halders1982]

Also curious what’s the best technique for oxidised pads? How to avoid them? And how to fix them based on the state of the pad.. rebal and clean? Clean with a fiber pen (messy fibers all over) or steel brush? scratch with a knife?

[@chrisami876]

Great tip to reflow the solder balls in the middle layer before putting the sandwich back together

[@VCCBoardRepairs]

Glad it was helpful!

[@cyprusiphonefix7339]

Was just doing a 13 pro max and did it like 3-4 times to get it right but your method is great .. Will do it the next time THANKS for all your efford....

[@VCCBoardRepairs]

Give it a try!

[@riyanwhyte8365]

Bro, thank you, but what I'd like to know is the heat you used to join the sandwich together. Is it the same heat temp to separate it?

[@furgeltay819]

This video helped me a lot thnx man ❤️❤️❤️

[@teraintegra89]

good vid jesse i use xzz l2023 and amaoe middle layer reballing , if u dont mind pls do a vid how to remove glued ic with highest succest rate

[@VCCBoardRepairs]

I have many videos on that. Check my channel

[@mm0077]

Thank you for sharing. Great job.

[@VCCBoardRepairs]

Thanks for watching!

[@MasonVanDerWatt]

Great video Jesse. Thank you. What temp did you use on the i2C to split the board?

[@VCCBoardRepairs]

I use 210C on my heater. Your temps may vary

[@ezeigwechidozie827]

Thank you boss please sir can you make a video on how use and understand zxw software very well thank you boss

[@VCCBoardRepairs]

Many of my videos show how to use it. Just keep watching 😀

[@riyanwhyte8365]

Since the dt80 Dc power supply is no longer available, which should I use?

[@platineshop]

Great Job and congratulations on showing and losing so much time with editing... so that everyone can understand how to do this type of work 😊

[@VCCBoardRepairs]

Glad you enjoyed it!

[@alienencounters5710]

nice my friend

[@VCCBoardRepairs]

Thank you!

[@khalifasolution]

I remember few yeas back when iphone 10 come out gives me headache to do it . for me AMAOE stencils are very good for me from iphone 10 to 15 serie .but why are you remove thermal past what will cool down CPU and lower board stuff ?

[@VCCBoardRepairs]

Because it makes a mess & the phone works fine without it.

[@kinghassan9834]

Smooth Reball as you

[@VCCBoardRepairs]

Thank you very much!

[@sukhpreetsingh5548]

which solder paste is good for layer reballing 138c or 158c

[@VCCBoardRepairs]

158c. The one I show in this video

[@kingsfordboamah8372]

I directly reflow it on the I2C without the soldering station

[@VCCBoardRepairs]

I find it's safer to use hot air to flow the paste Because removing the board and putting it on the heater will risk touching the paste and messing up the reball

[@albirossi8963]

Hello Jesse, can i ask u what ISO alcool do u use? thank u

[@VCCBoardRepairs]

This one: amzn.to/3Ktgs8v

[@haliimaaxmed]

thanks jesse, do you use this low melt paste (158) for data recoveries only or you can use it for fully repairs wich can survive more years

[@VCCBoardRepairs]

For repairs as I show in this video

[@haliimaaxmed]

@@VCCBoardRepairs thanks

[@TonyToneFixMyPhone]

I put my bottom board back on the heater instead. Try it.

[@VCCBoardRepairs]

Not necessary

[@jeremiahgeo]

what Flux did you say that used here? I could not see it , can you please it share it

[@VCCBoardRepairs]

Wuzip Flux: wifixusa.com/en/products/flux-syringe-10cc-wuzip

[@haliimaaxmed]

jesse bro i have small budget and i want a solder station do you recommend me aifen a9 to buy it

[@VCCBoardRepairs]

i dont know. I never used it

[@yessobeu]

thk,bos

[@VCCBoardRepairs]

You're welcome!

[@jtw7777]

you heart must have sunk when you seen that OLED Damage, The worst bit about repairing these days is possibly damaging the screen.

[@VCCBoardRepairs]

Haha yep. Luckily, I checked the ticket and saw my tech noticed the damage when it came in. So wasn't on us

[@SomeOrthoBro]

Video idea: how to pay you 20$ to read the panic log on an iPhones.

[@VCCBoardRepairs]

Genius 😂😂

[@kingsfordboamah8372]

Hello. Am good with microsoldering and am from Ghana. I have good experience and good ethics. I hve have bee watching your videos for couple of years now. I will be glad if you choose me whenever you want an employee. And am 23

[@VCCBoardRepairs]

Thank you very much!

[@snrshaggy9067]

@@VCCBoardRepairsI texted you yesterday with a similar message via the locals,but hmmm…..

[@r2dslayer676]

Is their anyone to accept fb request in your group?

[@VCCBoardRepairs]

Yes, you most answer all the questions to join

[@FekaJohnk]

💯💥👍

[@VCCBoardRepairs]

Appreciate it! Thank you so much

[@markhoryt6881]

183 ur 138 pest😊

[@VCCBoardRepairs]

158C. Link in bio