I retired from 40 years in the business a few years ago. I had studied a bit of Japanese joinery before anyone knew what a cat paw was. I had two faced hammers, one side flat for driving the nail and opposite side was convex to make the last blow to the nail head so as to not leave a dent in the wood. Also they use square faced heads not round so as to be able to nail in a corner. Back then saw blades were called Shark Tooth design. They make their housing joinery slip joints because of earth quakes and that's one of the reasons they use thin pull stroke saws to be able to make extremely intricate joints. The problem with driving in nail that way is that the nail does not enter wood properly. If you look at the tip of a nail two sides are smooth and two sides are Sharp the sharp side should be driven into the wood across the grain to cut through the fibers of the wood so as to not split if you drive a nail into wood with the smooth sides in between the grain you split the wood. Of course that only applies if you're close to the end of a piece of wood and you're using Straight nails like finishing nails doesn't apply to twisty nails I had over twenty hammers cause at one point I collected antique tools. Back then they had some ingenious inventions we long forgot about
@arkadybron61205 жыл бұрын
10 minutes of total bollocks to get to 20 second point.
@miked18695 жыл бұрын
I stopped watching as soon as he said "You're going to have to wait around, though..." Um, no I'm not. See ya! :)
@lefrogie2915 жыл бұрын
That's what fast forward is for.
@beemoo71285 жыл бұрын
Guy makes a 10 minute video about a piece of metal and gets ostracized, Peter Jackson makes 3 x 3 hour films about a piece of metal and he’s everyone’s hero..?!
@royparsons96175 жыл бұрын
Arkady Bron .
@winnie-the-poohahaha44285 жыл бұрын
I zoomed to the point
@SB-gz5vh5 жыл бұрын
I didn’t know the waffle cut was for the galvanized finish to me it’s always been easier to hammer in nails because of the texture. I use an estwing like yours however mine did not come with the waffle cut so I took an angle grinder to it and made the waffle cut and it works the same as a waffle cut now. Always a good idea if you already have a hammer to modify it to your needs and get creative especially on a budget.
@fishbiscuit20005 жыл бұрын
Nope - the milled face grips the head of the nail better when driving it at an angle. It means fewer bent nails - nothing to do with saving the galvanising on fixings.
@kylefranklin52854 жыл бұрын
Yep that is right
@scottlytton53284 жыл бұрын
you are absolutely correct.
@michaels13263 жыл бұрын
If anything, waffle faces mess up the galv on the heads of nails MUCH more than smooth face hammers do. The feature is strictly a matter of increasing friction. And one doesn't have to drive an extended career's worth of 16d nails to understand this, either.
@troydixon33963 жыл бұрын
Nothing wrong with milled wood this hammer is solid
@ROBERTHOCKER Жыл бұрын
I noticed that also
@stephennovember22225 жыл бұрын
He needs to get to the point MUCH quicker.
@northwestendurogopro5035 жыл бұрын
He just keeps swinging those two hammers. *swing* * swing*
@mhwebb85755 жыл бұрын
Stephen November ~ He said in the first _30 seconds_ that the "tip"was at the _end_ of the video. All you had to do was fast forward or click to the end and then _you_ could've gotten to the point "MUCH quicker" all on your own! Don't blame him for your impatience.
@stephenodell42805 жыл бұрын
he does not have one.
@elonhoward5 жыл бұрын
The not so much of a secret is @ 7 mins 15 seconds
@Beaches_south_of_L.A.5 жыл бұрын
@Ironfukr 9 You saw ads? I didn't. Ha ha ya nail banger.
@thegoodfight3655 жыл бұрын
hey Vince. I'm 52 and recently helped a friend build a work shed. His nephew had a couple pals to help move equipment. That said I was astonished at how many young men have no clue how to use a hammer 🔨 Were not talking a piece NASA technology here. Thanks for the tool tip 👍🏾
@Trig1885 жыл бұрын
wrong reason given for head milling. It minimizes slip on modern framing nails with similar head patterns when striking the nail. never had anything to do with preserving galvanized surfaces.
@cattleshredder22105 жыл бұрын
Dudes a clown
@jcsmithco99425 жыл бұрын
So True! Thank you, from a 40 year carpenter. "preserving galvanized nail heads?" . . . . absolute rubbish.
@ELW29405 жыл бұрын
Only way to preserve galvanized heads is don’t strike them with a hammer. Sometimes it do...sometimes it don’t. Come off that is.
@calvinsusanwebber34145 жыл бұрын
Ralf you are right you also can straiten a nail as you drive it with one
@alexbelle39414 жыл бұрын
That’s what my father told me when he gave me his Estwing.
@meagain60285 жыл бұрын
20 oz Estwing claw hammer has always been my fav. Great for overall use. I've even split small wood with it. Lol
@VCGConstruction5 жыл бұрын
In always using the claw to split wood to get at fasteners that are set too deep
@scott1lori2822 жыл бұрын
I have a Craftsman 20 oz straight claw. All steel, rubber handle bought 1992. So many nails drove. Still in use & will hand down to a grandson.
@edurmston83105 жыл бұрын
Who would possibly own a hammer with a nailed-shaped indent on top and NOT think it’s for setting nails?
@mhwebb85755 жыл бұрын
Ed Urmston ~ You'd be surprised...
@DoctorTorque5 жыл бұрын
Or, like he said "didn't even notice". Who wouldn't notice that on the top of the hammer? Most of his videos are advertisements, hoping to get people to run out and buy whatever he's talking about. KZbin wants me to watth them, but his videos are all way too long for what you get out of them.
@johnsayman22715 жыл бұрын
@@DoctorTorque Don't like the program, change the channel
@42720055 жыл бұрын
Thanks for giving me the 9 minutes back :)
@lungbutter3615 жыл бұрын
Your mom
@concernedtaxpayersofcolesc83635 жыл бұрын
Dude it's a CLAW not a JAW, that's why they call it a CLAW hammer.
@MrMacrun5 жыл бұрын
We always called it a checkerd face.
@Jbuss06795 жыл бұрын
@@MrMacrun He is talking about the back of the hammer where you use it to pry out nails and yes it is called a claw hammer straight claw or curved lol. What you're talking about is what the hardware store calls a milled face or smooth
@timhenson41845 жыл бұрын
I thought the milled face was to help keep from slipping off the nail head
@fixitman215 жыл бұрын
It is...
@billyandrew5 жыл бұрын
Made the same point, before scrolling down to these comments.
@romanreckless82635 жыл бұрын
Why the F would u want to scrap OFF the finish?. Why use a damn galvanized nail then.... what a moron
@eddiesmallhorn40215 жыл бұрын
I think the nail setting feature is a nice add to older and trusty technology.
@VCGConstruction5 жыл бұрын
Yes sir!!
@Kungamuck5 жыл бұрын
As being in construction for over 50 years I must comment on a few of your observations, the first being the use of hammers with steel shafts. Those that have worked in framing crews where 8, 10 and longer hour work days of continued hammer use has told old school carpenters that nothing beats a wood handled hammer to save the hand and forearm from continuous pounding . Granted, if you're prone to miss the nail frequently ( I should hope not )and strike the wood shaft.. or if you're using your hammer for demolition purposes, go with the steel shaft. Wood handled hammers are also much better suited for older tradesmen or those with bad joints etc. they're so much better on the hand and arm - as they absorb much of the pounding. As far as the top side nail holding provision - this is not 'modern technology' by any means - this feature was found on hammers for many, many years and a great help when you had to hang on with one hand when you drove nails with the other ... and like the steel shaft hammer were found in many carpenters shoulder boxes - along with a good Plumb hatchet !
@johnryan129211 ай бұрын
I used this feature for framing all the time, after a while it felt like loading a break action shotgun and i got really fast and accurate with it
@VCGConstruction11 ай бұрын
That’s awesome John, I like hearing how little innovations make work faster and easier! 👍🏻
@peterbarlow89122 жыл бұрын
These days framing hammers are just for finishing toe nails and other nails the gun failed to set deep enough. Just found my old Estwing 28 oz. In the bottom of a bin. I lost track of it 15 years ago after we got a Bostich N80C. For trim I use a rare 13 oz. Plumb curved claw. For destruction I use a proper Swedish Granfors bar paired with the Plumb.
@brandonjones3625 жыл бұрын
Im partial to you Eastwing 22 oz hammer . I have that same one I been useing in the garage door industry for over 12 years . Its the best !!
@markbaker94595 жыл бұрын
Wore out my 28 oz. Eswing as a union carpenter, milled face helps hammer blows to grip and direct nail and board as you mount the board. The other feature of the hammer's 'rip' versus 'claw' part, helps you as you remove nails or part boards that need to be reset.
@VCGConstruction5 жыл бұрын
Thanks Mark we appreciate the feedback!!
@markbaker94595 жыл бұрын
the steel shank and milled face were more than a useful feature, they were needed. Even than straught shank was very used in cleaning the faces of concrete spills on beams and braces. The 'rip' part could be sunk deep, quickly to form a ledger as a brace when you needed a third hand or tie up point. The later vanhang hammer's shock killing plug would have saved many an arm of pain and since I had and its nail setting groove and magnet were nice but too late since it was when I was full speed ahead, pain or not. Smooth faces were basically only for the 'finish crew'.
@ab22304 жыл бұрын
My grandpa lost his arm and had a hammer with the magnet head so he could set nails and keep working. Those have been around for a long time. This was back in the 70s.
@davefoster62235 жыл бұрын
For fecks sake does he love the sound of his own voice or what.
@mhwebb85755 жыл бұрын
dave foster ~ It was clear right off the bat that the guy talks during the video. But what did you expect? Sign language? When I first discovered KZbin, one of the first things I noticed about the videos is that nobody ever forces anybody to watch them! If his talking bothered you enough to bitch about it, why did you continue to watch it?
@heavenstomurgatroyd70335 жыл бұрын
He's no rocket surgeon.....
@mapex19765 жыл бұрын
That's over 9 my minutes I'll never get back..
@TheMulvihill5 жыл бұрын
@@mhwebb8575 get fucked
@brianmiranda84bm4 жыл бұрын
Its to make it to the over 9 min mark to get better revenue from the video.
@randallace3 жыл бұрын
Been watching the larry haun building videos lately - such a legend in framing - I’ve noticed he always black taped his hickory handles from the hammer head down at least 4 inches - any clue why he did that ? What benefit would that offer ?!
@crowhaven2005 жыл бұрын
hmm.. a milled face is to provide a bit of extra gripping surface to catch and sink nails, even if your angle is a bit off. It has nothing to do with galvanized nail heads. And steel framing hammers are hell on your joints and tendons, especially in your elbow and forearm. I know. That's why I went to a Vaughn 20 oz with a nice long handle for framing 40 years ago. It's all about angle and leverage to drive those nails. The steel estwings are great for demolition or pulling large nails tho. I still have my first one that ruined my elbow.within a year.
@Beaches_south_of_L.A.5 жыл бұрын
Exactly. I prefer a Vaughn 28 Oz or 32 Oz.
@michcarvao3438 Жыл бұрын
Got to say, love my nail starter. I work with concrete and it's a savior.. nailing cat walk bords or strong backs. It makes it a lot easier.
@Aepek5 жыл бұрын
Funny how such a "simple tool", is invaluable for doing any kind of construction type work....and honestly, are very technical when look deeper. My go to hammers: Eastwing Hammertooth(or sharktooth 😉) & Stiletto (which has the magnetic nail holder & a side nail puller). As always, love the tips/tricks videos you share with us. Cheers
@VCGConstruction5 жыл бұрын
Thanks Aepek!!
@shadowzedge57935 жыл бұрын
Very nice explanation of the hangers features. I knew about the nail setter function but not the reason for the milled face. Learn something new each day!!!
@VCGConstruction5 жыл бұрын
Thanks Shadowz Edge!!
@jerryriggan5 жыл бұрын
Hangers? Not true about the milled face
@paulyg775 жыл бұрын
You are one heck of a professional, Vince! When I have questions, you are my #1 go to on KZbin. I truly appreciate the time you put in to keeping brothers in the know!
@VCGConstruction5 жыл бұрын
Thanks Mr. Magic I try to do what I can!
@johnthompson66985 жыл бұрын
For sure!!! O.k. the milled face on the hammer (everybody knows) is to peel the skin off of your finger if it gets in the way. Makes you feel good.
@MrShinta7865 жыл бұрын
Didn't know that, thanks. I'm still using my unbranded 60's hammers which my dad gave me... They still work fine, even the wood is good
@VCGConstruction5 жыл бұрын
Somethings will always work!!
@torekman6955 жыл бұрын
I first looked att the clip without sound. Your bodylanguage tells me that you are perfectly balanced and comfortable with your Eastwing. When you pick up the Vaughan the way you move tells another story. From manoevering with your wrist to swinging the whole arm to do the same work. So I turned the sound on and to my suprise I hear that you consider them totally interchangeble.
@VCGConstruction5 жыл бұрын
Very scientific approach!!
@carlosbmartinez4085 жыл бұрын
I didnt know about the milled face saving the galvanized head on the nails. I always thought it was to "grab" the textured head of a bright nail, so as to minimize bending while striking. Great content by the way.
@VCGConstruction5 жыл бұрын
Do you mean Textured head on a galvanized nail? That’s there for the same reason!
@carlosbmartinez4085 жыл бұрын
@@VCGConstruction Our bright hand bangers have a diamond shape texture kn the head. I was told years ago that the waffle head was meant to "grip" the nail head so there is no "slippage"...maybe it serves both nail heads?
@Woodchopper464 ай бұрын
I had a wooden handle, curved claw hammer with a T-shape nail groove between the crotch of the claw and the shank, the nail was held in place by two spring loaded ball bearings. One spring & bearing was inserted into a hole drilled from each side and capped with a set-screw. Nail setting hammers are not new. Taking a nail and pushing it down past the ball bearings was probably not as fast as sticking the nail on a magnet but it was more secure and took more that a little bump to dislodge the nail. I got mine about 68 years ago. Some low-life took a shine to it in the late 1980's.
@callumbush14 жыл бұрын
How you keeping your hands in such good condition?
@WEALRO5 жыл бұрын
I love my estwings but I got a Hart steal neck 21oz and it has a nail puller on the side of the head also, Great Job Vince👍
@artiep63585 жыл бұрын
The milled face also is cause 16d nails have a milled face as well and it’s a non slip feature so you hit nail true.)
@brianfalls58942 жыл бұрын
I've got both of those hammers that you are talking about here. My Vaughan is my newer hammer that I used in the garage door business. When I was in the concrete business I purchased an Estwing and it is also a great hammer.
@stephenleepmg1135 жыл бұрын
Thats really cool. I never thought of that. Lol !!!!! I'm an Estwing fan. I use the 28oz flat, the 20oz flat, and the 32oz roofing hatchet. Estwing I think is the best hammer on the market , and has been my choice for ruffly 30 years. I have to say super cool idea on the Husky lmao !!!! Thanks Vince !!!!
@VCGConstruction5 жыл бұрын
Thanks Stephen Lee!!
@jerryriggan5 жыл бұрын
No such thing as a 32oz roofing hatchet.
@stephenleepmg1135 жыл бұрын
@@jerryriggan Yes Jerry there is. In the late 1980's at a True Value Hardware store the Estwing 32oz roofing hatchet was available for purchase. I am a proud owner of the said hatchet. To my knowledge the same hatchet is available at the Home Depot. Please contact Estwing customer service to confirm that. You sir should try one. There great hatchets. Good luck with your research.
@HartDoug5 жыл бұрын
Thanks. I do have a ‘fairly new’ hammer (less than a year old)... It DID have this feature (and I never noticed)...
@VCGConstruction5 жыл бұрын
Thanks Douglas, was it a hart hammer?
@HartDoug5 жыл бұрын
Not sure what kind it is... There’s no name or manufacturer’s mark that I can see... I took a picture of it but the comments don’t appear to want to allow me to ‘post a picture here on...
@shannawilliams3487 Жыл бұрын
Thanks - I have the Husky....just looked at it and thought I was missing a piece. I immediately came on here to see what it was for.
@williamstyers42645 жыл бұрын
Saw this same feature on Harbor Freight's 22 oz "California" framing hammer 5 years ago. Not really all that new but not a lot of people aware of it. My favorite hammer is a12 oz. Bluegrass that I use for trim work. Sadly the company is no longer in business as I understand but it is a damn fine hammer for light work. Well balanced with a nice hickory handle.
@EternityForest3 жыл бұрын
He looks like he'd be an awesome renaissance polymath painter! I like sub 12oz 6" ish hammers. I do maintenance and tech, not construction, and most of the stuff I do really shouldn't use *any* nails at all because we like quick repair access. The tiny ones are perfect for noy weighing down a bag for something you hardly use
@jimzhou53812 жыл бұрын
Estwing Ultra series also have the nail setting mechanism as well as the side nail pulling V notch.
@akatedgo73315 жыл бұрын
My Estwing 20 oz. straight claw is used for everything. Same hammer is 35 years old and still going.
@BuzzLOLOL5 жыл бұрын
I have a couple of those Estwing hammers... they were $33 in hardware stores... found mine at closeout in Big Lots for $3 each...
@BuzzLOLOL5 жыл бұрын
@Connor - The all steel one shown with rubber grip...
@stephenodell42805 жыл бұрын
i can tell you all you need to know about hammers. -1 framing hammers are above 20 oz they are for driving heavy nails 10 penny or larger. can be near 30 oz. have a waffled head and strait claws, aka ripping claw. 2-. middle weight 16 oz may have a ripping claw or curved claw that is better for pulling nails has a smooth head so if you miss you don't tare up the wood like a framing hammer would; use on 4-8 penny nails. 3- finish hammer, 13 oz or less used on trim, molding, that sort of stuff. use with finishing nails. 4- handles: a steel handle will transfer the shock to your arm, wood will brake but will not shock you as much. Fiber handles is what I used. The longer handles gives you more power on the swing. You can use a lighter hammer and still drive the nail. Remember this always pick the nail for the work and the hammer for nail. Always buy a hammer that feels good in your hand and you can swing as long as you have to. Is that easier?
@VCGConstruction5 жыл бұрын
Thanks for the feedback Mr. Odell !!
@peepgames49855 жыл бұрын
"give ya my lil tip at the end"😂😂🤣🤣ha
@CarbonGlassMan5 жыл бұрын
Loved my Eastwing. Even though my swinging it at concrete for a number of years damaged my elbow pretty good.
@VCGConstruction5 жыл бұрын
The repetitious movements will get you in the long run buddy!!
@CarbonGlassMan5 жыл бұрын
@@VCGConstruction yeah, and when you're young, the older guys warn you about that, but being young, you don't listen. I'm young, powerful, feel great. I'll be fine. Then age catches up to you and I'm like, I should have listened. That damn elbow and knee are pissing me off again.
@VCGConstruction5 жыл бұрын
Sorry to hear it buddy! The old timers know the deal, now will the young guys listen to us!?!?
@CarbonGlassMan5 жыл бұрын
@@VCGConstruction haha Hell no! They're young and as invincible as I thought I was. Love your videos man. I miss my construction days. I still build, but it's with molds, fiberglass and carbon fiber composites now. A lot less physically demanding.
@VCGConstruction5 жыл бұрын
Just gotta take er easy, we only get one body!! Nice talking to you my friend and good luck! I hope to see you around more often!! Have an awesome day!
@chrislogue57445 жыл бұрын
Do they make another hammer besides estwing? 23yrs and never used another brand. Had a California framer by Craftsman with orange fiberglass shaft that was the only thing even close to the balance of a estwing but they stopped production of the Cali framer after only 2 years in 2002.
@richhawkins20395 жыл бұрын
Never met an Estwing tool I didn't like, especially their hammers. I have my grandfathers, similar to the first one he held up in this video - unstoppable. Even the grip is still in great shape, and that thing got abused. Stay the hell away from Dead On though, their tools are cast, not forged. Yes, they snap - ask me how I know. :D
@ELW29405 жыл бұрын
Also have Estwing cats paw, hatchet, camp axe.
@chrisfyfe40475 жыл бұрын
I’m no carpenter , but my default hammer is a 6oz Crosspien , with a sawn off handle , I pull nails with pincers , anything I cant pull I cut off , and set , I also have a couple Ti Stilletto prybars .
@VCGConstruction5 жыл бұрын
Wow awesome!
@tritonmemnon58015 жыл бұрын
Rare comment but we suggest you and others with the milled face on their framing hammers, should clean up and sharpen the face for more efficient use. The clean up improves strike and impact. Keep up the good work
@johngallo4485 жыл бұрын
I learned something new today! Don't believe everything you see on the internet. Much of it might be BS or just one guy's opinion based on his range of experiences.
@larrykirkland18715 жыл бұрын
Been a carpenter since 1972 and have never heard the nail pulling part of a hammer referred to as jaws. Out west here we refer to them as straight or curved claw hammers.
@JackStraw0078005 жыл бұрын
Larry Kirkland same here in the south. Also, I've never heard a cat's claw referred to as a cat's paw.
@outfctrl5 жыл бұрын
Don't forget the small hole at the bottom of the Estwing rubber handle. It is not used to hang the hammer. When I was a carpenter, I used to set nails above my head. Put the nail head in the hole, swing it and set the nail.
@krich1063 жыл бұрын
Which hammer would you buy, if you had full blown tennis-elbow?
@sergiogard82645 жыл бұрын
Yo Vince, what do you think of the DeWalt hammer line up? In Europe, they are not easy to find. I will have to special order them, have you ever used have you have used these hammer? Are they worth the time and money, for me to special order them? DEWALT 20 oz. Hammer-DWHT51054 DEWALT mig weld framing hammer DeWALT DWHT51366 DeWalt XP hammer DWHT51380
@VCGConstruction5 жыл бұрын
The 14oz that hits like a 28oz made in Mexico is my favorite of the DeWalt hammers
@DIYRAYMOND5 жыл бұрын
Awesome. I've never paid any attention to that. I don't have an "updated " hammer. But think that this will be one of my next features to look for on a hammer. Thanks Vince and all of VCG CONSTRUCTION love the videos
@VCGConstruction5 жыл бұрын
Glad we could help! Thank you!
@ELW29405 жыл бұрын
Use your Dremel and add it.
@maglidiusliberty69575 жыл бұрын
I have a california framer (vaughn) that I got in 1997 with a nail set and a waffle face, still works great :)
@fortransecurities99765 жыл бұрын
Same, it's been my favorite hammer for years.
@warningsystemsofohio18803 жыл бұрын
Thanks for the video I leave for a hyper tough stub clawhammer and it has the same function which is pretty dope
@whatsthebigfndeal2 жыл бұрын
I've been using the same 20 oz estwing every day for nearly 30 years.
@charliewhite56755 жыл бұрын
know why a framing hammer is 16 inches long ? .... a layout reference for decking a roof or running sheathing ...
@robcrowley752 жыл бұрын
I saw nail holders on 1990 German brick hammers . Scutch on one end nail holder with waffle texture working in London in the 90s when all the brickies came back from rebuilding east Germany .
@randallace3 жыл бұрын
Just bought that husky hammer in the 22 oz size based on this video - nice hammer !!
@richardhamilton77865 жыл бұрын
In my late father in law is an old hammer with a small spring loaded steel ball and a grove cut into the top of the head to hold a nail is you can set the nail one handed. this hammer is over 80 years old at least and is functional. Who knew? Very good video. Thanks.
@brutus18084 жыл бұрын
My vaughan stealth framing hammer 17oz have one of them it's full steel hits great only had it a few days looks solid like it going to last my whole life I am not replacing it there is no need to replace a fully steel hammer
@vojnikjna305 жыл бұрын
Milled face is good for drywall as well. Great video
@VCGConstruction5 жыл бұрын
Thanks Vojnik!
@richardshea314 жыл бұрын
No it's not god for drywall. A drywall hammer is waffled but it has a curved head so it leaves a dimple and not rip the paper and a hatchet end to shave of chalk that is excessive on the ends. I guess you didn't have to mud the job and have to fix all the holes you made in the sheetrock.
@johnkatify5 жыл бұрын
Nothing new here this feature was on hammers 50 years ago . It was placed between the claws and held there be detent balls.
@sticknstonesbrkbones5 жыл бұрын
I did not know that about the milled face. I thought it helped driving the nail straighter by gripping the nail head better. I have used mine as a meat tenderizer, did you know you can do that? lol Its kinda like using a heat gun to toast a samich lol
@VCGConstruction5 жыл бұрын
Sometimes using the tools unconventionally works best !
@MostlyPeacefulCombatVet5 жыл бұрын
Yo congrats on 40k subs bro! Incredible! I think I just congratulated you on 30k like last week. Lol! You're a beast cuz! 👊
@VCGConstruction5 жыл бұрын
Thanks David we appreciate you!!
@kidcarpenter74395 жыл бұрын
I use a 23oz vaughan framing hamer with a wood handle that thing is a beast! (it is a waffled hammer)
@VCGConstruction5 жыл бұрын
Sweet Joey!!
@hilohaianmolinere71685 жыл бұрын
Well damn first time seeing that new tech on a hammer. Going to get one in the morning. Heck I owe You a cup of coffee.
@VCGConstruction5 жыл бұрын
Awesome cause I love coffee Ian!!
@76shogun15 жыл бұрын
It's not new tech.....this guy just makes it seem like it...What's next?showing us a chalk line?
@hilohaianmolinere71685 жыл бұрын
@@76shogun1 Well its new to me and I am happy to know about.
@rayring86795 жыл бұрын
Love my old estwing 22oz hammer mill face that’s my go to but my recent purchase was the Hart 21 oz mill face and that’s been nice addition.Vince what’s your thoughts on wood handle hammers? Great vid I could talk about hammer for hours
@haroldshinski79225 жыл бұрын
Had my set of Estwings since 1967 ! Most framer use nailers today !
@VCGConstruction5 жыл бұрын
That is correct
@chillout10015 жыл бұрын
I did know this ,I have one and got it because of that,it can be handy when you have only use of one hand.
@VCGConstruction5 жыл бұрын
Awesome!!
@jerryriggan5 жыл бұрын
A nail gun would help.
@ensinitas5 жыл бұрын
so what your saying is that there are different kinds of hammers? revolutionary! what should i use to get MAXIMUM waffle in my finished deck? which is best to assure slipping and damaging finishes? i was taught that the mill face was to get massive thumb damage as rapidly as possible. was my handyman sensei wrong?
@samadrid63214 жыл бұрын
Difference I find is straight claw and curved claw. They both have their type of jobs. A 20 oz. is nice to slam those nails, but a 16 oz. has more finesse. Sometimes I just use a screwdriver, a pair of pliers or even my pry bar to hammer something if I'm too lazy to go get a hammer.
@larryloftis90645 жыл бұрын
I built pole barns in the 80's used 9 inch nails and the reason for the waffle cut was to keep the hammerhead from slipping off the nail head, it made a huge difference drove thousands of 9 inch nails. I have never ever heard it was for galvanized nails. Just doesn't make sense to me always used smooth headed hammers for that.
@GFlCh5 жыл бұрын
Another uncommon feature I've seen... I have a Craftsman hammer that's probably 20 years old, or more. Unfortunately, I can't find it right now, I think someone borrowed it and didn't return it. Anyways, I think it's 16-ounce or 18-ounce. It has an all wood handle, but it has a steel sleeve covering (protecting) the handle near the head of the hammer. This is where the uncommon feature comes in. On one of the hammers claws, it has a tapered v-groove cut into the end (tip) of the claw. This can be used to pull nails when space is limited. I've seen the magnetic nail starter feature on some hammers, but I don't own one of them.
@VCGConstruction5 жыл бұрын
Thanks for the feedback Kevin !!
@firstlast-yn4qg2 жыл бұрын
wuz about to treat me a new hamma since my grip was old but covered it with gripped shrink wrap instead.
@jeffalan63392 жыл бұрын
My dead on has open neck for shock control , hammers are getting improvements from curved to straight now titanium custom built replacement head cool.
@TheGameBoy565 жыл бұрын
I always thought that was a sight like on a gun lol it always fails when u pull the trigger and smash ur self in the face loooool great video Vince my dad has that exact hammer but he paints everything green so no one can steal it
@VCGConstruction5 жыл бұрын
Good move painting the tools!!
@Jawsjawsjawsrg3 жыл бұрын
Thank you 2:36, that is literally what I was trying to find out.
@mikerojas66265 жыл бұрын
7.5 minutes in before he tells us about the "SPECIAL FEATURE". Pffftt!!! I had this "SPECIAL FEATURE" over 35 years ago on 2 of my hammers.
@jackthespratt5 жыл бұрын
LMAO......cosign!!!
@TombstoneHeart5 жыл бұрын
Yeah, this bloke is a real oxygen thief - he could talk underwater with a mouth full of marbles.
@tuberzish5 жыл бұрын
My great grandfather had a hammer with a nail setter in 1960!
@saraducky5 жыл бұрын
Can you find some of the cheapest but best compact circular saws?
@VCGConstruction5 жыл бұрын
Sure
@gerardjohnson21065 жыл бұрын
Been using a Bluegrass 16oz claw hammer over 50 years. Original hickory handle, no splinters. Never found another with comparable balance. Estwing 20oz straight jaw wrecking hammer is OK for its purpose but for EDC the Bluegrass is in my hand. This hammer was high dollar when I bought it but it has paid for itself 100,000 times over. Yall don't know what you're missing.
@VCGConstruction5 жыл бұрын
I’ll check it out thanks for sharing!!
@ELW29405 жыл бұрын
Gerald you...like me...probably paid $6 for your first hammer. Mines a 13oz Plumb. Still hittin the nail on the head after 50 years. I bought the “innovative” fiberglass handle !
@stonystoner8955 жыл бұрын
I would have watched this if the tip was first. I don't wade through small talk to get to the point.
@karlsimonian14245 жыл бұрын
Yet you did. And commented. Awesome.
@dianafertig21885 жыл бұрын
He told you at the beginning, the tip was at the end. You could have fast forward the video.
@radinsyah15745 жыл бұрын
Two thirds into your video and I’m still not seeing the ‘overlooked feature’.....
@raptureready95025 жыл бұрын
Hey brother I just bought a new Milwaukee hammer 19 oz and I tell you what it is a great hammer. Pulls nails nice and I can sink 16 penny spiked in 2 licks! Great ha mer
@VCGConstruction5 жыл бұрын
Nice Rapture !!
@Motorman-dl1sc5 жыл бұрын
Great video . I have the Craftsman all steel hammer with the rubber grip. What i like about the all steel hammers are they stay together. Those old wooden handle always come apart or break the handle. I was tied of always trying to hammer the metal piece in the top of the wooden handle hammer to expand the top. The steel hammer is like 20 years old and still works like new.
@VCGConstruction5 жыл бұрын
I agree, steel neck hammers are most versatile, and durable!!
@diynurse15615 жыл бұрын
Thank you that was interesting info... Great Video
@rickprice4075 жыл бұрын
As far as weight - where will you be hammering? Waist level and below - you can go pretty heavy. Working at or above your shoulders and I'd go significantly lighter.
@brunog13265 жыл бұрын
Do you know why the “Hart” hammers have changed the finishing looks different, mainly cheaper than the older one I have.
@JimVincitore5 жыл бұрын
Great video! Very cool! Thank you!
@VCGConstruction5 жыл бұрын
Thanks Jim we appreciate it !
@piecetoyou82855 жыл бұрын
I did this to my old hammer years ago,I drilled a hole then epoxy a earth magnet in the hole, then i used a disc cutter to cut the groove for the stem of the nail,then a dremil disc cutter for the head of the nail groove,took me 20 minutes to convert my £3.00 hammer to an expensive one
@scottpowell61455 жыл бұрын
Cool addition
@999thenewman5 жыл бұрын
I like when Vince makes these, "Did you know?" segments.
@neallauron19563 жыл бұрын
EDC hammer! awesome! i need to get serious, commit and pick my EDC!
@antoinewilson10264 жыл бұрын
That nail setting feature is awesome.
@paul-ld9vh5 жыл бұрын
I had an old drywall hammer that had a dimpled (and larger face) for hammering in nails into drywall when it was done that way. The dimpled face kept the drywall paper intact.
@VCGConstruction5 жыл бұрын
Nice
@ELW29405 жыл бұрын
Also helps the mud adhere to the face of the rock.
@richardshea314 жыл бұрын
@@VCGConstruction It's not supposed to be used for sheetrock, it will tear the paper because the head it flat and you cant sink the nail deep enoght with tearing the paper so the head is exposed and no round dimple in the sheetrock to comer the head, and the finish taper has to fix everyone that's wrong!!!!!
@richardshea314 жыл бұрын
@@ELW2940 What???? you use a sheetrock hammer people....
@ELW29404 жыл бұрын
Richard Shea Don’t understand what you’re trying to say. Do you even know what a drywall hammer looks like and it’s uses ? None of the ones the guy in the video demonstrates is such, they’re all framing hammers.
@nateperry43295 жыл бұрын
When do you think Home Depot will get the xdt16 in stores?
@802Garage5 жыл бұрын
Learned no less than two awesome things in this video. Thanks as always!
@VCGConstruction5 жыл бұрын
Thanks 802 Garage we’re glad the video is helpful!!
@paulk53115 жыл бұрын
i have several hammers and none of them have this feature. for high reach stuff we have this thing we call a ladder. works pretty well too.
@nedflandersdittlie5 жыл бұрын
When you only have a hammer... everything looos like a nail....