VControl Touch Nitro Setup and Tuning Tips!!!

[@gnielsenjp]

That was extremely useful to help me setup my first nitro heli after many years, thank you!

[@ghtheli5784]

Very informative, Ron!

[@NitroClouds]

Nice video, thanks for taking the time Ron. very helpful even for the non-touch VBC. A Vbar Neo tuning video series with step by step instructions- showing symptoms of different issues and how to correct them- would be awesome. I can’t get my logo 550 to piro in one spot. It travels all over the place. I bought it used and will do a rebuild to spec but I’m wondering if that is a main rotor gain issue? I had this problem once in the past. The tail also has a slow wag but this was a poor build, I’ll see if it’s there after the rebuild. Any ideas on the piro issue? Pack CG seems perfect and this problem happens with different pack sizes and weights. Auto trim worked ok-ish for hover but the Heli wants to tip over on spool up. Thanks

[@jeffallsbrook3999]

Can you do video for buying pro/rescue and installing for receiver .

[@laughingstill]

I’ll try and do one soon

[@Brass-and-Bullets]

Is there anyway i can get in contact with you to go through my touch.. got problems 🤦🏼‍♂️

[@radobohac9222]

Hi Ron, hope you are well. Do you use BPS-1 directly to VBAR or have you reduced voltage via step-down reg. pls?

[@laughingstill]

Direct to the VBAR depending on your voltage going to the VBAR. LiFe is safe

[@radobohac9222]

@@laughingstill I use 2s LiPo, not sure whether it will burn with 8.4V, maybe worth to try. How many volts do you have pls? Many people say there need to be step down reg for BPS-1. I have Spektrum too, that one work fine.

[@laughingstill]

BPS-1 is good on 2s

[@laughingstill]

Wait, now that I think about it I did step the voltage down for that semsor

[@laughingstill]

***Sensor

[@Gungospel_762]

Futaba BPS-1 RPM Sensor Works with the V bar

[@leonardgerard2159]

Verry helpfull video🙏

[@laughingstill]

Yes, if it in a Non pumped OS motor. Have not confirmed with YS

[@jimmydickins]

Waiting on my goods, So N556 do you set it as 550 or 600 in the set up thanks

[@laughingstill]

Jim Penrose 550

[@slackering]

Did you ever have a chance to make the follow up video going over PID and basic throttle? Can you put a link here or in the description please?

[@dbirds21]

Hey ron. Is that my n5c I sold you

[@laughingstill]

Yes sir!!!

[@laughingstill]

All needs to be connected

[@very9000]

Listen, CH1-3 is clear, but why center CH4?

[@laughingstill]

Not necessarily needed for some heli’s. If you have an older mechanical CCPM then you will need that as well

[@very9000]

@@laughingstill THANKS A LOT. I want to use telemetry, but I am using a V-Bar governor, do I need to use the Governor Scorpoion or not? (I have V-BAR CONTROL and V-BAR NEO, ESC - SCORPION)

[@laughingstill]

No, you can see the telemetry with the VBAR gov. You just need the cable that goes from the computer port on the esc to the telemetry port on the NEO

[@laughingstill]

shop.mikadousa.com/05089-VBar-ControlScorpion-ESC-Cable-500mm_p_1774.html

[@very9000]

@@laughingstill Thank you, I connected it today, but here's the problem: it shows 50 mAh, I haven't connected the engine yet. Could this be, or was it just that I set up the V-Bar Governor badly? Tell me, is it better to use Governor V-Bar or Scorpion?