I am also impressed with your build of the panel saw! I know this is an older video, now - and you mention in comments that you have a newer design. If you still have them, I would love to receive a copy of your DIY plans as well! [edit: email removed - plans received]
@crossgrainwoodproductsltd92303 жыл бұрын
This has to be the nicest panel saw setup I've seen.
@AlexPSNB3 жыл бұрын
Thank you
@kcswampertb3 жыл бұрын
great job how is half sheet stop in there
@anrivera118 жыл бұрын
Very nice panel saw!. Has everything I am looking to build in one.
@josephjoe90888 жыл бұрын
Great video. I love it. Could you please send me the plans
@xXLLcOoLDiEgOXx11 жыл бұрын
amazing !!!im from cancun mexico and we dont have all the parts to make it but im waching all the vertical panel saw videos to take the best way to make it
@ParleysWoodedJourney6 жыл бұрын
Thanks for the plans. Now I know at least one project I want to tackle this year. :)
@jamesrigelman71548 жыл бұрын
Great panel saw and great video. I wish I would have seen this years ago. Any Chance I could get the plans for this too???
@armanflint13 жыл бұрын
Very Nice... The conduit with rollers makes it super nice.
@GoofyboyCR78 жыл бұрын
best DIY vertical panel I have seen so far. Can I dare to ask for plans? That would be awesome. Thank you!
@arjoy19958 жыл бұрын
owesome design .... best of all. can you share the plan ?
@valdircristinosilva4998 Жыл бұрын
Belo trabalho irmão, parabéns . Mostra como vc fez esse sistema de molas p subir e descer a máquina
@AlexPSNB Жыл бұрын
Olá, as molas eram de um antigo conjunto de exercícios de peito que eu tinha por aí, mas você também pode usar alguns pedaços de elástico de borracha, isso faria o mesmo trabalho, usei isso na segunda serra que fiz e funcionou tão bem quanto as molas
@AlexPSNB Жыл бұрын
Me mande seu e-mail que te mando algumas fotos da segunda serra que montei, que funcionou muito bem.
@rocketburner31910 жыл бұрын
very clever consruction seems to be very handy and easy to use i prefer a vertical panel saw because its much safer than a table saw may you always keep your ten fingers best regards from germany
@projectsforcreativeminds17974 жыл бұрын
This is the best budget sliding panel saw vid iv seen, there is a guy whos made a computerised one which is also fantastic but this saw will appeal and satisfy many woodworking enthusiasts. thank you so much for sharing.. if you would be willing to sell me a copy of the plans so that i may copy some of the ideas for my own id be very grateful, thank-you.
@bauenmann13 жыл бұрын
Hi Alex, Fantastic piece of equipment - I've been think of building something similar for a while now. Two questions: 1) When doing a length-ways cut (horizontally), what if the cut you need to make happens to be right over one of the horizontal supports, above the mid-fence? Won't you cut into it? 2) Similarly, when doing a cross-cut as you demonstrated, don't you cut into the fence?
@johnwurst66917 жыл бұрын
Best one I have seen! Great concept, looks easy to use!
@matteocoscia92458 жыл бұрын
it is indeed a brilliant design, would love to see the plans if possible!
@AlexPSNB8 жыл бұрын
send me your e-mail address Matt
@matteocoscia92458 жыл бұрын
mcoscia@yahoo.com, thanks so much!
@dustmedia12188 жыл бұрын
ME as well - gerrie@dustmedia.co.za
@thelosttexan17177 жыл бұрын
Beautiful job! was hoping you could send me a link to the plans. or whatever is best thank you.
@AlexPSNB7 жыл бұрын
send me your e-mail
@papaike25 жыл бұрын
Alexander sure looks like everyone is wanting the plans for your saw how about it?
@AlexPSNB5 жыл бұрын
Send me your e-mail address bud
@shadetree10108 жыл бұрын
Great design! Could you email me a copy of the plans? Thanks
@mattweaver32773 жыл бұрын
I love this idea. Are the plans still available.
@AlexPSNB3 жыл бұрын
Sende your ail address
@mattweaver32773 жыл бұрын
@@AlexPSNB mweaver527@yahoo.com
@AlexPSNB13 жыл бұрын
yes it took about a week to get all the parts together and it was basically done using the Shop notes design with a couple of alterations to that ,glad you liked the saw
@matermark10 жыл бұрын
Great job you did on that panel saw! I think I recognize the way that it attaches to the pipe as a ShopNotes version, I will have to look for plans. What modifications have you made to improve the original plan?
@martinwalters19547 жыл бұрын
Great design. I see below you are willing to send plans. What type format are they in? I use Sketchup mostly, but let me know please. Again, great design and execution.
@Kucciolo7711 жыл бұрын
Hi there, I am Italian and I really would like to know if you have a plan to build your vertical panel saw. Your job is great. Thank you.
@Burdennnn11 жыл бұрын
Good day, i wonder if you will still have the plans for this machine... Could you please let me know if you do, i used to have my own woodworking company, and due to financial problems was forced to sell all my equipment... Im thinking of trying again. but dont really have the money to do so... PLEASE help me!!!
@NathanNostaw10 жыл бұрын
Thanks for the plans. I see you have a few tweaks on the original plans. If you were to make another, are there any other changes you would make? Do you find when making a ripcut/horizontal cut you have the top board trying to bind the blade? Is the horizontal rest for the board sacrificial on vertical cuts?
@AlexPSNB11 жыл бұрын
Hi there the timbers behind the panel being cut are sacrificial and come time will need replacing these are still the same ones iam using on the saw from the first day i started using the saw and as yet havent replaced any.hope this helps
@yvesvallieres32007 жыл бұрын
This is great design. Would it be possible to have the plans please? Also one silly question, what happen when you have to make a cut that ends directly on a back support stud?
@AlexPSNB7 жыл бұрын
send me your e-mail
@AlexPSNB7 жыл бұрын
the back supports are sacrificial
@romadalessandro69547 жыл бұрын
Congrats. Great looking tool. I know I'm commenting a little late but is there a chance I can buy a set of plans? Thank you
@AlexPSNB7 жыл бұрын
send me your e-mail address
@carlosmario59918 жыл бұрын
Congratualtions, Alexander. the best designs I've seen I would love to have a copy of the plans if possible, I thank you in advance.
@AlexPSNB8 жыл бұрын
MARIA ANTONIA send me your e mail address
@carlosmario59918 жыл бұрын
Alexander Birnie Hi, alexander, my e mail address is carlosmario20142014@gmail.com
@Bicongerman8 жыл бұрын
Hello Alexandre, are you able to email plans for this? I got really surprised about your design!!
@66kushy7 жыл бұрын
just what i was looking for, could i bother you for a set of plans. would be greatly appreciated. thank you very much.
@heikofranz51288 жыл бұрын
Hi Alexander, that is one heel of a design, could I trouble you also for the plan? Thanks heaps
@Irene154513 жыл бұрын
Alex, Very nice construction! Where can I find the shop notes design you used? Thanks for your video. You wife did a good job with the camera and sound also. Reuben
@sherbetlemondesign6 жыл бұрын
Fantastic design, could I get a copy of the plans or purchase a copy?
@AlexPSNB6 жыл бұрын
David Ward Send me your e-mail
@sherbetlemondesign6 жыл бұрын
Many Thanks dave@versarack.co.uk
@deezynar13 жыл бұрын
That's very well made. Is this based on the plans that Shop Notes had?
@OneManBandWoodworks8 жыл бұрын
This is one of the best designs I've seen, are you able to email plans for this?
@AlexPSNB8 жыл бұрын
+One Man Band Woodworking send me your e-mail address
@OneManBandWoodworks8 жыл бұрын
+Alexander Birnie Thank you, message sent.
@saxofono20118 жыл бұрын
+Alexander Birnie , please can you send me plans for vertical panel saw? thank you
@bpez31063 жыл бұрын
Great job. I assume that you could also make an adapter for a router? I have been thinking of this for awhile and think for the investment and for limited space, this would be a better option then a table saw. Do you charge for the plans? Thank you for your time
@PaidinFull20242 жыл бұрын
Excellent craftsmanship! Are these plans still available?
@AlexPSNB2 жыл бұрын
Send me Ur email address please
@AlexPSNB2 жыл бұрын
Birniealexb@gmail.com
@remiixedreview4790 Жыл бұрын
Did you end up getting the plans?
@edbuell6712 жыл бұрын
@AlexPSNB Alex can you post a couple pics of the rollers and the central support you added . we are getting ready to bhuild one that will handle 5X5 sheets for the NortheastWoodworkers shop near albany ny.
@wattvaktarn Жыл бұрын
Hello, is it possible to get plans for ths amazing design?
@AlexPSNB Жыл бұрын
Send me your email address
@eduardocosta90787 жыл бұрын
Hi Alexandre, that´s an amazing job, congratulations!
@PADZERFAY098 жыл бұрын
is it possible to send me plans? brilliant idea.
@davetierney70858 жыл бұрын
cracking saw, just what im looking to make, can you send me the plans
@AlexPSNB8 жыл бұрын
Send me your address
@simonsimon40512 жыл бұрын
what happen at the end of an horizontal cut when all the weight of the upper piece of wood push against the sawblade? What prevent this?
@franktrough60658 жыл бұрын
Hey brother great job done here, I would gladly purchase one if you would be willing to sell one except the saw I have two. Which is why this project would be good to use one on.
@SPITFIRECARPENTRY13 жыл бұрын
i love the inventiveness of carpenters
@bobbg90417 жыл бұрын
Look out when they figure out they can also use metal cutting tools too.
@TheChsmith6 жыл бұрын
This Panel Saw looks like the same plans that appeared in Woodsmith magazine 8/2014. It looks like you have different verticle guides, added rollers on the lower rail & your upper guide is pipe rather than 1-1/4 EMT. I ordered a set of plans but have not started my build yet. I plan to rotate my saw via a center point & locking pin (raise the blade & plunge in zero clearance slots) I hope it works) Good build, how long did it take you to complete?
@leelawrence2215 жыл бұрын
Great video - can you send me the plans. Thanks
@hoplahey11 жыл бұрын
At 8:04 what prevents you from cutting into the resting board (where your panel rests on the rack).
@miltonaugustosilva506511 жыл бұрын
Hello Mr. Alexander, my name is Milton, I´m from Brazil. So, I would like to buy the plans of construction of this vertical panel saw. It´s possible?
@tomhill40036 жыл бұрын
Very Nice! Please make the plans available!
@AlexPSNB6 жыл бұрын
Send me ur E-Mail
@Pucallpillo7 жыл бұрын
Hello, I repeat my congratulations ..... that good work, the best I've seen, and I wrote a year ago and now I would like to know if you can sell those plans, excuse the insistence.
@AlexPSNB7 жыл бұрын
Mario,send me youre-mail address and i will send the plans on to you
@Pucallpillo7 жыл бұрын
Alexander Birnie ..... my mail: mueblescovalto@hotmail.com and mueblescovalto@gmail.com ..... thanks.
@vancla84 жыл бұрын
good evening I have a small joinery in Brazil and would like to be setting up your project. you could send the saw project. Thank you very much in advance . claudiorlara@icloud.com
@nelsonmeza77843 жыл бұрын
Excelente trabajo....Podrías facilitarme los planos y medidas...Gracias
@mirobotcnc68417 жыл бұрын
Hi. Nice job! I'm in the process of making one. I've the idea but have some thoughts on the bearings.. can you tell me how did you put them?
@AlexPSNB7 жыл бұрын
send me your e-mail address
@Jayson1940D1411 жыл бұрын
Do you still give out plans for this panel saw? Thanks, Jayson
@SHRIMP111127 жыл бұрын
are you still sending the plans out
@leonelsantizo554810 жыл бұрын
Hi, Congratulations!! good job, could you send me the plans?
@AlexPSNB10 жыл бұрын
send me your e-mail address
@leonelsantizo554810 жыл бұрын
Just in case, if you forgot send the plans my email is jlsantizo.jls@gmail.com
@hawasnowhawa624810 жыл бұрын
Alexander Birnie can u send me plans my e-mail is snowhawaiiano@gmail.com
@visionerdesignandbuilders4059 жыл бұрын
This is great!, Can u please send me plans as well my email is visioneridesign@gmail.com? Thank you.
@wohnungsfrei7 жыл бұрын
schubert_ricardo@yahoo.de :) thanks
@heltonsilva95848 жыл бұрын
Boa tarde Alexander Birnie, gostei do seu invento como faço para adquiri seu projeto.
@jairoalcidesvillamarin86655 жыл бұрын
Desde Colombia gracias
@bpez31063 жыл бұрын
Opps, hit send to quickly. What sort of accuracy are you getting?
@AlexPSNB3 жыл бұрын
The saw is very accurate for sawing panels to size,send me your email address will send them onto you
@bpez31063 жыл бұрын
@@AlexPSNB Thank you for your quick reply. Email prince.barnwood@gmail.com. Stay safe
@johnschmidt77398 жыл бұрын
Alexander, Can you send me a copy of the plans also?
@abdellaghezali993 жыл бұрын
Bonjour Monsieur, j'ai vu beaucoup de vidéos sur les scies verticales, pouvant me donner des idées sur mon projet d'en réaliser une dans mon atelier. Vôtre scie m'a enthousiasmé. Auriez-vous conservé les plans de vôtre réalisation, et serait-il possible de s'en procurer un exemplaire s'il vous plaît. Cordialement.
@AlexPSNB3 жыл бұрын
Send me your email address
@abdellaghezali993 жыл бұрын
@@AlexPSNB Merci pour vôtre réponse. Voici mon mail: kancress@yahoo.fr Cordialement.
@mohhammadsosaraie6 ай бұрын
Dear friend, you made this project with artistry and creative ability Can you provide me with this plan?
@AlexPSNB6 ай бұрын
Send me your email address...
@mustaphaben29212 жыл бұрын
Hello any plans ?
@nejobsteve12 жыл бұрын
if you have planes on how you did this would love them
@hughterry60710 жыл бұрын
Great job. trying to get one together
@Marcellus747 жыл бұрын
Dear Sir, I am gathering all the material to build a similar saw, thank you for your video and details about it. Can you please tell me the kind of spring you used to compensated the weight of the tool ? They look like garage door springs but the wire diameter of these is always too big and the springs are too stiff. Thank you for your help. Best Regards, John
@AlexPSNB7 жыл бұрын
John Martin it was the type that is used on the old type of chest expanders. My latest saw that I built uses the rubber bungee cord and it works just as well
@Marcellus747 жыл бұрын
Thank you very much for your answer, I just found a used "brand new" arm stretcher with 3 springs 2km from my home for 5€. Thank you for the tip ! Building of the saw can carry on...
@AlexPSNB7 жыл бұрын
John Martin okay that's good you have managed to get springs..I wish you success with your build.
@erichesketh60287 жыл бұрын
Alexander Birnie . Can you please supply copy of plans for your diy panel saw ? To elphesketh@googlemail.com
@augustoascanio86509 жыл бұрын
Buenos días, disculpe usted podría facilitar los planos de esa sierra vertical.. Gracias
@matermark10 жыл бұрын
ALSO, what's the maximum capacity? Can it cut 5x5ft Baltic birch sheets?
@truebluekit10 жыл бұрын
He did say it will cut a full size 4'x8' sheet.
@davidquintana561710 жыл бұрын
Very Good Job I like It.....
@thejet411512 жыл бұрын
is there a parts list and instructions how to build one, if so would u be able to send via e-mail? thanks
@brewsterly29278 жыл бұрын
Very nicely done Alexander. You may be getting tired of this request, but I too would very much appreciate a copy of your plan. Have liked and subbed.
@AlexPSNB8 жыл бұрын
Send me your email address
@shekharrvs8 жыл бұрын
nice one ...could you send me the plans too @ rvsshekhar@gmail.com ..... saw your new yawl ...nicely made......
@AlexPSNB6 жыл бұрын
It took about,a week on and off if I remember correctly,I have since built a different design and if you send your email I will send you some pictures of the Finnished saw.
@hansjakob80876 жыл бұрын
Alexander Birnie i would Readly like to have Theo Plans in it is possible please Write back and i will sende Mythos E-Mail But i Will Not send my E-Mail if im Not sure you Write back
@kennyruhl36136 жыл бұрын
i would love plans of this saw and pic plans of the new saw. This is awesome. kruhl@rti-inc.com
@leelawrence2215 жыл бұрын
That would be great if you could send me pics of the new panel saw and any plans that might be available, my email address is lwlawrence123@gmail.com. Thanks
@marclauze58518 жыл бұрын
Hi, is good job! Is possible to send me plans. Thanks
@keithmartin41198 жыл бұрын
can you send plan
@AlexPSNB13 жыл бұрын
yes it was i just made a few changes to the shop notes design
@emmanuelbusto46929 жыл бұрын
Alguien me puede decir como hago para que el disco no me toque en las maderas de atas de la maquina? gracias
@همسةهادءة4 жыл бұрын
رهيب عاشت ايدك
@atruebiblicalchurch11 жыл бұрын
I just found your video and have ordered parts for the Shopnotes design but was interested in your design would you be able to share the alteration with me if i sent my email address?
@33LEANDROHER2 жыл бұрын
Excelente
@33LEANDROHER2 жыл бұрын
Super top
@jessestrum12 жыл бұрын
why not make money and pay a specialist for a good one of the the shelf.try selling it and see the responce
@rogerromero571212 жыл бұрын
goodnight as they call media you are using to the saw suguetar
@Mr2at11 жыл бұрын
now thats clever. Bravo
@LJG78113 жыл бұрын
very nice......
@jessielove797 жыл бұрын
Thank you
@RoyThe4th6 жыл бұрын
Thanks for sharing well done
@sailingcatcharay11 жыл бұрын
Super!
@stevendavis74568 жыл бұрын
Nice!
@AlexPSNB11 жыл бұрын
send me your e-mail again as the one you wrote is not reconized
@josecastillo-nl4yg8 жыл бұрын
exelente
@kadikardigans448311 жыл бұрын
nice.....
@nearzlake111 жыл бұрын
Or buy a real one for 200$ used like i did, easily used as a panel router as well.
@balysvitkauskas82728 жыл бұрын
Hi , Alexander , can u send this plan to my e-mail address?