Very few people know, the secret of the welder is making precision 90 degree joints on square pipes

[@dandeeteeyem2170]

Don't know why so many people are commenting about how they already knew this... Why come here? 😂 The video describes a common mistake, which is overcome by doing something counter intuitive. I remember many, many years ago thinking I just wasn't cutting close enough to the corner 😅 great video

[@Ronsreypich]

are you mean?

[@dandeeteeyem2170]

@@Ronsreypich I was genuinely thanking the dude.. But yes, I am average, if that's what you were asking :P

[@KBLIZZ333]

​@@dandeeteeyem2170 🤣🤣 perfect response.

[@নওশাদ90]

Thank you for such a beautiful video ❤❤❤ I want to see more new videos like this ❤❤Thank you for such a beautiful video ❤❤❤ I want to see more new videos like this ❤❤

[@wellnesslifecaresolutions3511]

Great.. Thank you so much

[@seanbryers29]

Thanks for this video i learned something new 😊

[@mranil99]

Thanks 🙏🙏❤

[@nimrow99]

Thank you, I benefited from your beautiful ideas and wonderful videos🌹

[@idetubeid]

Thank you very much 🙏

[@SaeedSaeed-vt6om]

Cool work thanks 👍

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@iiscantik4721]

Kebangetan manstabbb bang.. 👍👍👍👌

[@jdcmber]

Thanks!!

[@masterQ20]

Thanks for sharing. God bless you 🙏

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@veeramuthus581]

Thank you❤

[@INDOWELDER]

Good job bro ❤️👍👍

[@apk9357]

Thank you so much

[@Jigsofficial16]

Nice thanks for sharing this video bro❤

[@WELDING_INDO]

trik yang sangat sempurna sekali bang inspiraasi dalam segala hal

[@KBLIZZ333]

I need to try this on 1/4 inch thick 2x2 steel tubing. Wish me luck.

[@CinDeihLian]

Good job 👍

[@mdsarfaraz9469]

Good work

[@azwanpalugada3842]

Terimkasih ilmunya...👍

[@romellyarde907]

i didnt see where the measurement for material thickness was measaured in and used can you tell me i am lost?

[@ieyazzu9297]

1:30 check. Used as a tiny gap between straight line vs 2 point line at 1:35

[@IRONcrafs]

❤ I like your videos and I also make similar videos.

[@JenieferTelmosa]

Thanks for your cher your teknek cutinng tubolar next vedio

[@curonelectricity]

I like your video ❤❤❤❤❤

[@totoy33]

재관의 달인 재관의 기술자. 최고입니다 👍🏾👍🏾👍🏾

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@codygallik2261]

The music set me straight into a wonderful mood. That was good.

[@psee919]

Nice 👍

[@fafa8447]

Good 💯

[@ma-lakshmifabricator7549]

Overall, this is a highly informative and enjoyable video for anyone interested in fabrication. It showcases your talent and expertise while providing valuable insights and inspiration to fellow enthusiasts. Keep up the great work, and I look forward to watching more of your content in the future 👍👍👍

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@dwaynelejeune3508]

You show lot of tips/tricks on cutting angle and square tube metal, what about cooping round pipe

[@Mightiflier]

Am I the only one who is almost counting out, 123123123123123 at the beat of the music while watching this video?

[@Mightiflier]

Something about the whole thing is relaxing and rewarding.

[@jorger.m.j.7494]

Me too, I'm going to put that topic when I have to do some work....and for crafts or drawings I recommend the following one. m.kzbin.info/www/bejne/qZqmnqSsm9ySZ8k

[@dianavergara5652]

boss gudeve anu po ang sukat ng pinaka makapal na tubular

[@rafaelmolina123]

Can this be done on a c channel bar?

[@KBLIZZ333]

Yes

[@edemoi3817]

This ai known But good work.💪🤩👍

[@jimsmith8071]

So, you made a nice joint in the middle of the tube. What are you going to do on the other two ends of the tube? What is planned final product you are making?

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@XavierLENOZACH]

tres pro merci

[@NoNo-dq4mc]

Cut it thru at 45, flip one side 180 degrees, chamfer your edges , butt weld. It is faster.

[@fernandoparcel]

De que medida es el metal

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@rcytb]

Wouldn't "leaving the line" (cutting inside the lines) accomplish the same thing?

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@จ๋าชาวไร่ทํางานหาเงินทุนกลับบ้]

เยี่ยม

[@Ernie-Tech]

Yep, nice vid but too bad that the cutter didn't run the edges of the cut metal down a bit just before plying the corners together. This would make the welding easier since a gutter-form is created and so the welding penetrates better. Spoken comment misses, this makes understanding so much easier.

[@ArvInd-vd2ww]

I did not understand a thing about what he did. Just by drawing a line the cut became perfect? I see no difference between the first cut and the second one. Can anyone explain to me what he did?

[@KBLIZZ333]

He didn't take into account the thickness of the material in the first cut. The second one was measured right to the edge minus the thickness so he was able to cut closer to the edge so when he folded the two pieces together there was no gap.

[@snowwarden3711]

so instead of a point we have 2 points that r the thickness apart?

[@ASMguitR]

This is not a secret. Very many people know to account for wall thickness, including all professional welders. But useful for those starting out.

[@Mightiflier]

Very helpful info to that group, which was a secret to them

[@seanbryers29]

I did t know this

[@KBLIZZ333]

I'd imagine this video isn't meant for experienced welder/fabricators

[@LeoA-t4z]

Dijeran en mi rancho, no pues chido 😂👍

[@danieltrombeli6610]

Show de bola

[@jeffwells4072]

Can someone please explain the difference in the first and second cut. I see the little line he made but the cut looked the same

[@tdentertainment8768]

Khác nhau hoàn toàn, lần thứ 1 cắt sát mép. Lần thứ 2 cắt bỏ 1 khoảng nhỏ ngoài mép.

[@ryanariate2040]

The distance on side. He measure the thicknes of its side the thats it

[@KBLIZZ333]

He didn't take into account the thickness of the material in the first cut. The second one was measured right to the edge minus the thickness so he was able to cut closer to the edge so when he folded the two pieces together there was no gap.

[@budda3258]

Зачем лишняя резка проф.трубы!Покажи сразу же 2 вариант!

[@semiproapologizing7622]

I dont see the difference at least you just cut all through the top triangle

[@vanhuynguyen9124]

Exactly

[@AlekseyKrigin]

Я тоже так делаю, первый раз не правильно, а потом правильно.

[@Сергей-ф5з6п]

Покажи как из отвода 90 сделать угол 37 градуса.столкнулся на работе

[@NextBangkok]

👍👍👍👍👍👍♥️

[@michaelfernandez7237]

So whats the trick

[@johnhiggins2685]

Ha ha. I laugh at all the comments on here. Everybody finding faults. Ok here's another one. Would it be better to put a full penetration weld on the first one, rather than just spanning the joint on the 2nd😅.

[@MalaBi-l9e]

Je veux souder

[@ewaspirydowicz4561]

Super Super Super komentarz 👍. 🇺🇦

[@Tool-Tips]

youtube.com/@Tool-Tips?si=nIGBH99jHW-XKPbA

[@MaryJaneYagao]

❤

[@mahmoudabuelazm7961]

👍

[@بهاءحلووم]

👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻👍🏻

[@JohnnyHarness-e9t]

Did anyone see the ants fighting on the table.

[@txxr542]

Those tricks are for small projects. I haven't seen video where some welder can improve more in the 45° cut. This wasn't helpful at all

[@hidupenak99]

Like & Subscribe 😊

[@ohhansel]

If you're going to be teaching people, how about teaching them to work safely ? Where is your guard for that grinder? Just look up pictures on the internet of people who didn't use a guard. When that wheel shatters you're going to hope there's a guard on there.

[@T.M....]

I agree. See it all too often, these channels disregarding safety without a guard. Just comes across unprofessional and cheap.

[@mikedillon9080]

That's because guards are for people who don't know how to operate a grinder. He knows how to operate a grinder safely but needs only cut 1 45° and flip the other piece and avoid wasting time & rod filling that huge gap

[@quaidq4771]

Guards are worthless and slow you down

[@adamnieuwhof3463]

Gaurds are there for a reason even if you know how to use a grinder you can still break a disc people make mistakes and if you have to take the gard off to get in somewhere your using the wrong tool

[@edwindol3597]

​@@T.M....obviously never used a grinder professional nor spend time in a shop full of professionals who work daily with grinders lol

[@Spitfiremetalart]

Buy a cheap chop saw,

[@walterdiaz2989]

😂😂😂este todavía no aprende usar las herramientas y quiere enseñar. Era tan simple como dejar la marca te comes la línea que hiciste con el lápiz. Aprende a usar las herramientas primero después te la das de profesor

[@gpena383]

😂😂😂 I rather have a gap for welding.

[@richardbart8256]

What a load of crap. Anyone can work that out but anyone with half a brain will see it's much quicker and easier to chop it once and deal with the extra but of welding.

[@หนุ่มเมืองสิงห์-ธ1บ]

ในคลิบก็ยังไม่ถูกนะใบลูหมูบางแพงมากตัดได้ไม่กี่รอยถ้ามีพาสม่าเล็กประหยัดกว่ามากในกรณีงานที่ทำเยอะจำนวนมากใช้พลาสม่าเร็วกว่ามากและประหยัดเงินกว่าส่วนใบลูกหมูเล็กเอาใบเก็บงานลบคมถ้าลบคมจะได้หลายงานมากตัดเฉพาะงานที่จำเป็นจริงๆผมเคยใช้ตอนสมัยเรียนเทคนิคอาจาร์ยให้เปลี่ยนมาใช้พลาสม่าแทนส่วนลูกหมูเล็กไว้เก็บงานใบเล็กๆใบเดียวใช้ได้เกือบครึ่งวันตอนเอามาตัดแบบในคลิบตัดไม่กี่รอยก็หมด

[@FRANCOISPOOLMAN]

Scroll by please I wanna watch and learn😢

[@igorberezin856]

I do it my way and never have to measure pipe thickness and it comes out perfect. I dont know what your problem is buddy