Printer prints without stopping Blank Sheets (The Solenoid)

What to do if the printer takes more than one page at a time, or it prints without stopping blank sheets of paper, the pick-up roller turns continuously and makes a paper jam. Probably you have a problem with the solenoid of the printer.
The solenoid is an activator for the paper pickup assembly. How to repair a solenoid.
For any question or suggestion leave a comment.
-----------------------------------------------------------------
email: [e-mail]
other links:
www.emmegiricambi.it/
-----------------------------------------------------------------

[@turkayp]

The technical explanation that i'm looking for. Thank you very much. I have repaired my printer by the help of your wonderfull representation. Instead of removing the pads which becomes sticky, i have coverd them with a capton tape. Now it's working flawlessly.

[@rigomatezoltan4302]

Thanks dude, I have just put some duct tape between the solenoid and that metal thingy, so it would not stuck together anymore. Now the printer works like a charm again.

[@lin2m3]

Just revived an old hp1018. First I thought it was the laser unit-changed. Then i started to dig deeper on KZbin. The arm coil was stuck. I've cleaned and put a small piece of double adhesive tape and not uncover the upper part and it works! Thanks!

[@hctkko]

Thanks, that was the problem with my ML-1640. After removing the sticky bit from the solenoid it works as new.

[@Ebikersplace]

The solenoid on the ml 1860 is viewable once the toner is removed. It's in the bottom left. Would it be possible to dust the sticky pad with baby powder using a small brush which should stop it being sticky without having to disassemble?

[@viandant5]

yes, it's for sure possible

[@Ebikersplace]

The paper jam issue is now resolved and no disassembly was required 👍

[@neanganududeun2018]

for the HP laser 107a, where is the selenoid located?

[@viandant5]

On the side, as the Samsung

[@directsystems2225]

hi sir, i have a printer Canon ImageClass MF3010, its getting paper jam when its enters into the pressor roller, i have checked the pressure roller and Teflon all are okay, and i have checked the Solonoid also, that is also good in releasing. and i have greased all the gears also, even though not solved the problem, any ideas

[@viandant5]

Cjeck the paper fingers, are they dirty? Try a ticker sheet a carton paper sheet to see if it remove something that could jam the paper

[@directsystems2225]

@@viandant5 i opened Fuser unit cleaned everything, changed the Pressure roller, Teflon roll, and greased gears., No dirty on the entrance, pickup roller also good, still issues

[@viandant5]

@@directsystems2225 May be the bushings are ovalized. What is the solenoid? do you mean the thermistor or thermostat?

[@izmirtoner]

dear sir , is there any selenoid on samsung m2675f? where is it ? ony any other part you know does same function? thank you

[@viandant5]

Yes, if I remember well there is a solenoid on the side

[@izmirtoner]

@@viandant5 i think there is another part like selenoid but it is not the same. i could not find it.

[@danielbayugar4856]

hi, in the m203 hp where is the Solenoid? thanks

[@viandant5]

It's on the right side. the part number is RK2-7601-000CN

[@danielbayugar4856]

@@viandant5 thanks is only one?

[@viandant5]

@@danielbayugar4856 yes

[@danielbayugar4856]

@@viandant5 thanks a lot!!

[@nsgnc]

Great explanation. Exact solution.

[@izmirtoner]

do you know where is this part on m2070 samsung printer? thank u

[@viandant5]

If I remember well the machine in the video is a Samsung

[@izmirtoner]

@@viandant5 where are u in italy ? i am going to travel on 23 january , to florance and rome.

[@viandant5]

@@izmirtoner Yes I'm in Italy but far from florence. I'm in Bologna

[@alichelbi4937]

I have a sumsung sxc 4600 printer, it constantly tells me "the cover is open, close it" while everything is closed. please help me understand and be able to repair my printer. thank you

[@viandant5]

here should be a tab in the cover that is inserted in a slot with a sensor. Check the sensor and the tab

[@alichelbi4937]

@@viandant5 I found the sensor on the motherboard, tested in EDC mode of the printer. it is functional. I can't seem to find the relationship between the error message and the actual failure.

[@viandant5]

@@alichelbi4937 And the sensor near the cover where the tab is inserted?

[@PatelNitinkumar]

kyocera 1025mfp Add Toner Error How To solution

[@viandant5]

You have to add toner changing toner cartridge, what do you mean?

[@trinhmai1550]

Help me. Relay paper not run??

[@trinhmai1550]

Sorry. It’s Solenoid

[@viandant5]

What do you mean?

[@trinhmai1550]

@@viandant5 Everything ok, green led, but when I press print test, printer not run. Paper solenoid is not run. Not pick up paper. No signal. Only dry light is on. And then red led. Are you use Facebook?

[@viandant5]

@@trinhmai1550 no, I have no facebook. It could be the main board

[@trinhmai1550]

@@viandant5 Machine now is ok. But only pick up 1 or 2 paper. More than, it is not separate. And not pick up paper