Voice Speaker repair, electronics

[@electronicshelpcare]

For the circuit diagram please visit here shorturl.at/FNS56

[@nelbztv]

Tnx master..we are watching 🙂😌🙂 very useful technic

[@amitabjaiswal6068]

वेरी नाइस स्पीकर रिपेयरिंग वर्क थैंक्स फॉर विडियो ब्रो 👍👍

[@ashokbhaighadiyali7394]

How did you decide magnetic center and physical center of voice coil?

[@AkiraNatchi]

this size is easier to centerize the cone. smaller than 4-5" or bigger than 12"-15", often after 2-3 months, you hear the noise of scratching and need to recone agaaaain 😫 a few pieces of thin papers must be slided inside center coil to prevent this problem till glue will be dried 😉

[@tedrobinson372]

They didn't center the voice coil. This is a bad video because they did not use shims.

[@stevetalin6489]

Basic repair principles are ok except I would be shocked if the coil didn’t rub on the magnet when completed. You must use spacer shims for proper coil centering. Also your coil depth is guess work.

[@githuikimondo9692]

How do you decide coil depth

[@SunilPerera-n1b]

බොහොම ස්තුතියි ඔබට පැහැදිලිව රූපසටහන පෙන්වාදීම පිලිඹදව.

[@CharlesDowiot-qv7pp]

New Again 🔊

[@CB-bo3tm]

Pardon my ignorance on speaker basics - would like a tiny direction for my problem. I bought a 8inch 50 watt woofer (not sub woofer) about 15 years back, used it for few hours and it sounded good. I opened it today and connected it to my amplifier and it outputs too little volume. I gently pushed the cone and spider up, and the volume goes up and it vibrates well. How can I fix it? The spider feels hard... the soft rubber on the outer edge of the cone is soft/flexible...

[@kyledefreitas89]

I have the same problem with two entire media rooms. Did you ever find a solution?

[@MuratOnal_RamsesElektronik]

Professional 🔈🔈🔈🔈🔈 Ramses elektronik olarak aramızda görmekten mutluluk duyarız görüntüleme ve ses sistemleri

[@shaheedghany428]

At what point did he center the coil?

[@ALHidayat826]

Sangat rapi dan keren,sangat ber manfaat sekali

[@souravbhattacharyya3392]

Great 👍 detailed fine work

[@kumaresanimmanuel6377]

Super demo thankyou bro God bless your work

[@Electronics0604]

Hello Master, im already waching your vedios, im a newbe vloger for electronics, i have got some ideas, so thats all thank u, god bless u master...

[@electronicshelpcare]

electronicshelpcare.net/tda2050-mono-circuit-diagram/

[@LAARCA10]

Yo no me dedico ese pero sinceramente lo hago mejor que él nunca me he quedado mal una bocina yo mejor no sabía ni un video así con ese tipo de forma de trabajar que me estuvieran viendo wowww

[@Rinkusingh-gn1jl]

बहुत बढ़िया बहुत सुंदर

[@sharukhmatekuki5830]

Good hit, Kuki dand 🇮🇳🇮🇳👍👍👍

[@crvelectroniccreations2203]

Your videoes seem quality and good

[@dylandream2248]

What kind of adhesive can be used to repair small slit on JBL L110 driver?

[@AdbelNasser-yj3un]

Salut vous êtes au cameroun ? J'aimerais.

[@ayambangkokjambinewperkakas03]

Good👌👌👌naxt ⏩⏩⏩

[@electronicshelpcare]

electronicshelpcare.net/led-music-level-indicator-circuit-diagram/

[@merlitomixvlogs9979]

Nice one sending my support fullpack new friend fullwatch from oriental mindoro Philippines

[@electronicshelpcare]

Please visit for circuit diagram www.pinterest.com/electrohelpcare/pins/

[@luishernandez9779]

Bien por tu vídeo amigo oye una pregunta , qué tanto debe d entrar el embobinado ? Gracias d antemano amigo.👍

[@norbertovisca8782]

sir, how about clearance, voice coil between, bottom center mag net?

[@muthupandian]

நல்ல பதிவு 👍👍👍👍

[@oscarbas2721]

You cannot do it exactly without putting spacer along the sides of the coil to have the same clearance..it should be done carefully.

[@ShriMahakalKripaJyotish0786]

X ray or fan binding wala kagaz is the best for spacer

[@dallie8206]

You shouldn't scrape the insolation off the coil wire either. Instead you must either use molten solder or lighter flame to do so. Good work but you will get 7 out of 10 from me.

[@luizcarloslau8929]

serviço muito bagaceira, ninguém faz um serviço tão porco assim.................

[@blueknyght923]

Can you use super glue (cyanoacrilate), instead of epoxy?

[@ceciljones1248]

No

[@KevinJackJill]

Please take care , many Amaturist seekers will try to take this as a basic ingredient to learn & practically perform this project. All corrected steps in the suggestion box be taken care of and new recording be uploaded for everbodys' s benefit.

[@tallLifts]

I mean, I'm not the most ocd person there is, but that membrane cut was something else.

[@rockylebon1153]

Good job 👍👍👍

[@willianmarques3258]

Obs tem que centralizar o centro da bina para não arrastar no canto para não fazer ruído. Isso ele não amostra no vidio eu já fiz varios

[@jayanthafernando829]

Very good speaker repair

[@CHURCHMISSION777]

Is a good video but i would like you to do a repair for Sony home theater woofer speaker since mine got burnt half,coz Sony says the connection between the 2 coils is cut. But the woofer does good in moderate volume, but when i go higher my home theater system go off and give a warning of power protect. So I don't know how to handle the woofer speaker . Any help?

[@tremendousmoviecanopy7674]

How do you identify positive and negative

[@vigneshwarar2201]

Super ,nice work .

[@AllboroLCD]

Def done the HARDER way! Still nicely done, easier to just buy parts that FIT!

[@bobbymcdaniel5163]

Hi I have an audiopipe 12in. Txx blue eye candy sub that was passed down from my brother that has passed away. So know it's the only brand I run. The dust cover sperated from the coil but the coil is still good. I had it in a sealed box and hit some low hz. that's the reason for it happening. It don't have to be the blue aluminum look just want to hear it play and bring back some memories of him. Please help ppl say throw it out and get a new one but I can't seem to do that. Please help me even if it is bad news.thanks for the time on this issue. Keep the videos coming they help out a lot.

[@sk-grant3614]

Даже не сомнивался что он его не будет включать на видео))) магнитный зазор не выставил.

[@brainwayOf]

да он там пиздец всё криво сделал, 100 литров клея вылил

[@moisesbastos1302]

E muito simples de monta um alto falante mais ele está fazendo o proseso mais difícil e só calsar. 1 passo. Calsar abombina. 2 depois passa acola. Nas parte metálica 3 cola abombina e 4 desses as cone faz a saldagem da bombima para os conequitores do alto falante. Desse o cone e o tapes.

[@timoteoucchan4655]

Buenas noches Excelente la tutoría. Aquí en Campeche, México, los técnicos usan resistol blanco # 850. En la tutoría no se cómo se llama el pegamento que usa. Será que lo vendan aquí en México y con que se pide. Habrá en cualquier eléctronica. Saludos cordiales. Desde Nunquiní, Campeche, México.

[@timoteoucchan4655]

Perdón. Con qué nombre se pide.

[@electronicshelpcare]

Please visit for amplifier circuit diagram electronicshelpcare.net

[@crisfher]

Where dis u get those parts I've tried to find it for months 😭😭😭

[@KevinJackJill]

The rusted body structure needs to pre treated manually before going on for the reconeing. Higher magnetic flux at bore & pole peace area will attract the rusted particles to reach there, even when the speaker is not in action. Secondly if structure is showing the tendency of rust formation, it should be nibbed at the earliest to save the refurbished component of same symptoms & saving other adjoining components as spilling of these particles are not good to other PCB plates like crossover Network or Mid Speakers in the enclosed Columb.

[@momomomo3906]

Perché il mio woofer da 18 pollici emette un suono tipo plac ad alto volume?

[@001officialdjcashdjcash5]

You are doing well

[@palabradedios.josesosa1326]

Grande colega te felicito

[@isaaclewis1163]

Hello great work. Where did you buy the parts from online.

[@vigneshwarar2201]

voice coil placement details super

[@chipietoby3084]

Pas de calage pour la bobine ?

[@snv4347]

Катушку в зазоре отцентровал по верхнему краю шайбы. Не правильно. Центр шайбы с центром катушки должны совпадать.

[@СергейАшихмин-е7х]

Он вообще будет играть?😅

[@Kolin4556]

он забыл что надо центровать, что-то измерял, я уж думал сейчас правильно выставит центр катушки по центру железа, а она улетела на дно магнита, он так и приклеил, лопух, 99% пишут nice work )))

[@luisburgos163]

Como dijieron la mayoria de todos ..le falto el centrado de la bobina y cuanto milimetros deja de bobina hacia arriba del nucleo del bobinado

[@tecassam2511]

Nice Tec👌👍

[@kishorkarki2190]

thanks verry nice video

[@brianwheeler4596]

which types of glue is needed

[@dallie8206]

The type that shoe maker uses.

[@dibyendumondal465]

Khub valo

[@rickybelaongtv.3994]

Good 👍 job

[@AnkadasuDanduprolu-pq8zt]

Super ❤❤❤😊

[@juniorjunior9118]

What adhesive do you use for speaker?

[@hdrali8118]

Araldite and fevicol sr

[@surajr3678]

This video used for dendrite and araldite

[@cheaiman4698]

What is name of all components. Like voice call and the other?.

[@chandrabhankathley6607]

Sir bol kar sikhate to or achha ho ta sir good app sa koi nhi batata sir

[@SONIDOSONYRUMBAIZTAPALAPA]

Y que no centran la bobina? Luego roza y se escuchan ruidos extraños en la bocina!!

[@ferminaguilarjuarez8174]

No sabes....hoy ..y loscentradores estás weeeeyyyy....😁😁😁😄😁😄😁

[@Marcomarleo]

Es un desmadre para repara el bajo. Falto centrar la bobina

[@mrsandipraj4088]

Hamare pass 50 watt espikr hii to kitna khracha lge ga

[@shekharchandwadkar]

I am also in electronic electrical mechanical field

[@josemirmauricio1644]

Eu refomo Alto falantes mais eu sentraliso a bobina e monto todo resto com sentralisada só no fim que retiro os causos

[@vigneshwarar2201]

Paper cone best or woofer cone best, which one best.

[@LheodaDjTechTv]

Watching lheoda tech sir nice sharing

[@dallie8206]

You're going to have a hard time playing that at a low volume. The coil will be touching the magnetized center. You must first assemble the coil, the spider and the basket (diaphragm) before glueing it to the frame.

[@renfordwesleyjackson7031]

true, also why cut the neck of the coil so short, there will be hardly any length left to attach the cone. problems

[@renfordwesleyjackson7031]

also what of the spacers to keep the coil centered before applying the glue

[@stephenkk1655]

Hello sir Dalton. I have a loud speaker but I want to get more bass from it. I was suggesting to transfer the cone to another basket that can accommodate a bigger voice coil. Already i have the basket and it has a has a bigger magnet. Will this idea work out as i continue to save some cash to buy a perfect driver? Please help me

[@beatprocess]

I bought speakers and the woofer doesn't have the connection where the +/- wires go

[@nbkvenom367]

Keep that work up 💪 👍 #BRUH#

[@aurelioislas5152]

Como se centro la bobina sin acetatos o negativo de foto,este si me salio chingon...

[@crearqarquitecto5252]

Eso es lo que también me dejó pensativo... como centró la bobina respecto al entrehierro y a la circunferencia externa del entrehierro? ... (No la centró en ningún momento)

[@chandrasenpratap5593]

I want to repair my JBL flip2.....how can I repair it

[@nvsingha2560]

Very nice video

[@officialkeyz4529]

You are doing well sir

[@amanuday2004]

Ahuja 400 wat mein Kitna number ka koil lagta hai bhaiya bataiye na please mere ko kharidna hai

[@electronicshelpcare]

electronicshelpcare.net/how-to-make-speaker-crossover/

[@jopietoisuta8985]

Lem apa yg dipake utk ngelem memran spiekerx gan

[@thusharabro9349]

very unprofessional... no voice coil balancing bad video

[@hartanto5540]

Tarik sis semangko...

[@bestactionmovieclip8493]

Sir 6" woofer speaker 10 watt coil ki jayga may 20 watt coil dull sakta hu kaya

[@DatLe-iw1gt]

Cần phải chuyên nghiệp hơn nữa nhé!

[@zenith3331]

Where is the spacer between the voice coil and the core to have the coil properly aligned ? I'm sorry to say but this whole speaker assembling process is incorrect from start.

[@ismacharia-gc4ig]

Let's see yours for comparison

[@rodzbeceril1627]

100% sasayad ang voice coil nyan.

[@shriraamsugavanam1870]

Are you trying to beat the speed of light???

[@EndikMania88]

Good👍

[@mkpiyarathne2944]

Good

[@joharyramly3345]

Hello can car speaker used at hi fi system

[@sutmungra4804]

Very good

[@haziboy6899]

What is the glue name ?

[@ahmadziadanish2334]

Bhai ye Sab saaman kha milega?inka naam BHI send karie.

[@ceciljones1248]

This is a old video but you learned the hard way didn't shim it it probably rubbed and shifted oh well you can break it down and re do it recone kits cost a lot of money now day

[@nilceutarkus8059]

serviço ruim não centrou a bobina com negativo,não entendi.

[@tvbabu4040]

Sir meri chupinchena speekar repai ki kavalachiña parts perrulu cheppaledhur

[@electronicshelpcare]

Please visit for circuit diagram www.pinterest.com/electrohelpcare/pins/

[@digitalcreator862]

U can Use Samad Bond or UK For make sound better

[@electronicshelpcare]

Please visit for circuit diagram www.pinterest.com/electrohelpcare/pins/

[@doceoutravessura8287]

Eu centralizo a bobina, pq se não pode arrasta,

[@fabianosouza8127]

Faltou centralizar a bobina com um papel

[@joseantoniodejesussilva9062]

Tô esperando ele centralizar tbm faltou

[@Android-wh2ed]

В руки насрать за такую работу. И что б воды не было...

[@ashishdecoration_Dj_tundla]

Superb sir

[@janakapiyaranjana2255]

Spicer priis kohenda ganna tiyenne