Volvo Penta Raw Water Pump Rebuild 21214599

[@paulnuebel5261]

Nice detailed video. Helping my pops fix his boat. Thanks..!!

[@steveludwig763]

Want to thank you for this video! I have some water leaking from my impeller and couldn’t figure out what was going on. Thinking I have a bad seal now, just ordered parts. Hoping this will keep me out of the shop for a little while. Appreciate you putting the part number also, made it very easy to find the rebuild kit online. Thanks again!

[@wdschwartz8386]

I think I have a bad seal now as well. Can you tell me where you ordered your parts from?

[@vinceadams1581]

Well done. Best video I've seen on the subject.

[@scottsmith2869]

Great video! I needed to see how to complete this repair myself. You showed me the easy way. Thanks

[@Rob000125]

Directions say the spring side of the seal goes towards the impeller... i believe you assembled it incorectly...

[@SchinwaldHans]

Sehr gutes Video, DANKE Hansi

[@ebwhits4132]

Great video. I will be rebuilding mine every other year. Only comment is that I believe you put the seal on backwards. From my knowledge, the cup side showing the spring should face the impeller and not the bearing...but I am certainly no expert. Thoughts?

[@jonprice78]

He put seal in backwards for sure.

[@mrprfct7069]

After 13:10. Does the pulley spin freely or is it hard ?

[@DLeake-73]

Awesome and very detailed and great instructions. Thank you. Where did you get your rebuild kit from ? Hope you posts more videos on the Volvo Penta’s.

[@AutomotiveAuthority]

The rebuild kit can be purchased here: www.automotiveauthorityllc.com/products/volvo-penta-sea-water-pump-repair-kit-21214595-21214596-21214599-21214601

[@mikel5601]

Just wondering I have the same one but the shaft pulls out of the pulley. Is that normal?

[@TheKeymaster316]

So if I have water dripping out of mine, would it probably be that O-ring or maybe the smaller seal that goes around the shaft? I just recently bought a boat with the Volvo 3.0 and at idle I didn't notice anything leaking. However, when I revved it up to around 1500 rpm's, I started seeing water leaking from this pump. I'm hoping a simple rebuild will take care of it. Thanks

[@TehButterflyEffect]

If it's leaking then the inner seal is bad and the entire pump needs a rebuild.

[@yugomoblv]

Great video!

[@booostedtc]

Nice video how did it work on the boat im afraid to heat and cool up stuff that seals water. I dont have a torch would putting it in really hot water for min or 2 work the same ?

[@dalton8089]

Where did you get that puller from?? Need to rebuild it ASAP and I can’t find a puller.

[@moccasinmarine]

My pump has plastic tubes leading into the impeller housing with o-rings. Does anyone know where to find the o-rings. I’ve searched and can’t find them.

[@booostedtc]

When you spun it by hand does it spin great or just a few turns you stop it with the one i took off it with make 2 turns only with the old one

[@TheCatsa]

Make sure you spin the impeller the proper direction and make sure they're all pointing the same way (back). I believe it was in the right direction but one of the fins was pointing backwards when you installed it. Overall great video. Thank you for your knowledge.

[@dustdevilmedia]

That is unecessary, the fins go the right direction once they begin to move.

[@TheCatsa]

@@dustdevilmedia Not the case for me when I replaced the water pump on my outboard. Had the fins going the wrong direction and they stayed that way until it forced water past the seal into the lower unit. I noticed water in the oil and disassembled the lower unit to find the flaps still pointing forward. I later heard not to rotate the engine backwards dry because of this same reason. Maybe just a fluke for me.

[@unapologetic7900]

My engine is a 2008 5.7 GI-J and uses the taller Impeller. Do you have a Kit for that application, or can I use this Kit and just get the proper Impeller separately?

[@wdschwartz8386]

I have the same engine and water pump. Did you find a kit for yours?

[@unapologetic7900]

@@wdschwartz8386 I ended up buying a new one from the dealer...talked them into a 20% discount.

[@changholee9201]

@@wdschwartz8386 Both type use same bearing and seal. I got one from Amazon.www.amazon.ca/gp/product/B079RMJ32G/ref=ppx_yo_dt_b_asin_title_o02_s00?ie=UTF8&psc=1

[@lisapaulparsons9549]

Nice , thanx.