VTEC NO WELD Venting the valve cover

[@chadnoswal9243]

I never thought about using a fuel cell bung. I need an AN fitting for a vacuum pump. Nice, and thanks for the upload!!

[@Zapzdoughnut]

That looks pretty clean. I dig it.

[@shankar3950]

Will oil enter the lines if there is no baffles? Isn't that why people install them on the top corner under the baffle...or am I wrong

[@GOAUTOWORKSYOUTUBE]

No, stay tuned to the next round of Civic upgrade vids. Subscribe and tune in, we'll revisit this and break down how it works more)

[@willis23jm1]

Way more oil, will exit through this fitting in that location... Best to bore hole within the factory baffle.... if its a straight car then it doesn't matter.

[@GOAUTOWORKSYOUTUBE]

@@willis23jm1 actually the catch can was fairly dry after several dyno passes and time on the street...but hey,...

[@willis23jm1]

@@GOAUTOWORKSKZbin was it connected to intake manifold vaccum or vented?

[@GOAUTOWORKSYOUTUBE]

kzbin.info/www/bejne/nqWrnqaugKtknac

[@TURBOTRISTO]

That looks soo clean Man

[@rj6198]

Do you have a link for the fittings?

[@chicoleno007]

Would I need another catch can if I were to do the valve cover

[@jooeee23]

Where did you get these fittings? Part number?

[@timothywalker1693]

I am currently doing something similar, just wondering if I should cap/block the original vent? Previously I had a small air filter adapted onto it, in an attempt to lessen the amount oil going into the intake, but finally getting around to doing a full PCV delete Breather style oil catch can system. But yeah, just not sure what to do with the original valve cover vent hole

[@GOAUTOWORKSYOUTUBE]

You can leave it open, run a filter, or block it off if sufficient ventilation avenues are being added.

[@timothywalker1693]

Thanks for the reply man! Do you know if there is such a thing as too much ventilation? The breather catch can I bought seems to have very good flow, but visually I quite like my little filter on the original vent, just not sure if too much ventilation can cause issues?

[@svera93]

What drill bit size did you use for the -10AN fitting to fit the valve covers? You're work is awesome btw!!

[@GOAUTOWORKSYOUTUBE]

Irwin step bit

[@svera93]

@@GOAUTOWORKSKZbin awesome but what size of the bit did you use (ie 7/8, 1/2, 3/8, etc)? I plan on taking your advice here and applying the same technique you used on my LS engine. Thanks!

[@Person-db9lw]

How did you get past the little lip on the inside? The bolt on the inside doesn’t fit as it makes contact with the lip. Any advise?

[@deko9151]

Dam I need those drill bits

[@bvyse1]

Someone messed up powder coating the inside of the valve cover. Any reason you would recommend having a vent with no baffle behind it?

[@brad.tripleog_jamaica384]

Where did you ran the other port too?

[@GOAUTOWORKSYOUTUBE]

are you referring to the OEM port/vent?

[@brad.tripleog_jamaica384]

@@GOAUTOWORKSKZbin I saw you ran one of the port to the head but I didn't saw where placed the other port. Did You installed it on the pcv valve?

[@EcFlipz]

How much oil do you see in the catch can since the fittings are below the baffling. Was thinking of doing it on the front.

[@GOAUTOWORKSYOUTUBE]

None after about 15 dyno pulls and a street tuning session...

[@EcFlipz]

@@GOAUTOWORKSKZbin I'm impressed. Will be trying this, thanks! 👍

[@GOAUTOWORKSYOUTUBE]

kzbin.info/www/bejne/nqWrnqaugKtknac

[@efcivic4life647]

Hey what was the two aluminum blocks for I'm try to do my set up with the catch can and I'm wanting to make my lines

[@GOAUTOWORKSYOUTUBE]

efcivic4life they are called “soft jaws”. They are used to go into a vice to hold the AN fittings while you tighten them together. The aluminum jaws keep the fittings from being scratched

[@efcivic4life647]

@@GOAUTOWORKSKZbin ok thanks for the info and love your videos I learn a lot from them

[@hellraisingvtec]

I like this idea, not sure if it would hold up to the heat while road racing.

[@GOAUTOWORKSYOUTUBE]

kzbin.info/www/bejne/nqWrnqaugKtknac

[@Stopsign32v]

Damn your work is top notch

[@GOAUTOWORKSYOUTUBE]

Stopsign32v thank you

[@candlepen]

This is pointless because it’s not baffled. It’s going to fill up that catch can immediately

[@GOAUTOWORKSYOUTUBE]

stay tuned to the next round of Civic upgrade vids. Subscribe and tune in, we'll revisit this and break down how it works more

[@GOAUTOWORKSYOUTUBE]

kzbin.info/www/bejne/nqWrnqaugKtknac

[@khairulafizi8362]

What if i want to put it at the front of the cover?

[@gaberealrc7355]

Hey brother do you have a link to that black an fitting?

[@GOAUTOWORKSYOUTUBE]

I'll add the part # in the next Civic Vid as the car is here for another round of upgrades (and the vent/cover/catch can setup on this car works great)

[@gaberealrc7355]

@@GOAUTOWORKSKZbin awesome appreciate it. My civics been in the dungeon for 4 years. Time to clean her up. Subbed brother.

[@eghatchtech92]

What catchcan are you using

[@youngn71890]

Hey @goautoworks can you make me a overflow just like that one?

[@landoski]

Do you sell that catch can on your website?

[@GOAUTOWORKSYOUTUBE]

currently, no. Maybe in the near future

[@thugsbryan]

Where can I get that fitting to buy?

[@joelvillalobos4279]

Have you had good luck with this? Any leaks? It looks great, and a nice option for those who have nice Valve covers;.

[@GOAUTOWORKSYOUTUBE]

The key to no leaks is drilling the hole the correct size for a tight fit.

[@GOAUTOWORKSYOUTUBE]

kzbin.info/www/bejne/nqWrnqaugKtknac

[@jamesthebond0072]

Abs so what is the point off this what does it do

[@GOAUTOWORKSYOUTUBE]

allows for greater ventilation

[@theedge5584]

Nice. How did you run your crank vent hoses???

[@GOAUTOWORKSYOUTUBE]

kzbin.info/www/bejne/nqWrnqaugKtknac

[@Mr334cobra]

Defeats the purpose of having a baffled vent! :\ Now oil will easily be sucked into that vent.

[@edomoralessilva5511]

yeah, that vent should be inside the baffle xD

[@Mr334cobra]

@@edomoralessilva5511 exactly. This is worse than leaving it alone.

[@coreymoto]

Damn makes sense thank god I read the comments before I did it. Without thinking it looks clean and you have your vent but your key point makes it pointless to do this unless vent is in baffle

[@GOAUTOWORKSYOUTUBE]

kzbin.info/www/bejne/nqWrnqaugKtknac

[@gonzotuned639]

Did this work??

[@GOAUTOWORKSYOUTUBE]

Yes

[@GOAUTOWORKSYOUTUBE]

kzbin.info/www/bejne/nqWrnqaugKtknac

[@lucasskm8233]

Wondering what benefits run bigger hole?

[@GOAUTOWORKSYOUTUBE]

the larger hole is less prone to create a "vacuum" on the port.

[@TwistedGarage616]

They shouldn’t have gotten paint on the inside of the cover..

[@TheShangralaaaa17]

whoever powdercoated that VC is terrible lol

[@321CatboxWA]

Why?

[@GOAUTOWORKSYOUTUBE]

kzbin.info/www/bejne/nqWrnqaugKtknac

[@TheShangralaaaa17]

no

[@eloscalb_3033]

Where can I get that fitting to buy?