UPDATED & FIXED***VVDI MULTIPROG failed to decode CAS4+ (5M48H) with Solderless Adapter XDNP12 V

THANK YOU @rikopli FOR THE UPDATE.
SW: V1.2.3.0
FW: V1.2.7
DB: V33
VVDI MULTIPROG failed to decode CAS4+ (5M48H) with Solderless Adapter.
in the beginning, when the solder-less adapters first came out the algorithm used to decode, the BMW Cas4/4+ module used to work perfectly. until recently, Xhorse decided to update the algorithm to decode/crack cas 4+ .
VVDI Prog the Original Tool is very different in terms of reading chips and decoding, certain MCU that are not found on the key tool plus or multi prog.
xhorse please fix the problem. This cannot be ignored
ADAPTERS THAT CURRENTLY DO NOT WORK ON MULTI-PROG:
1. XDNP12 - CAS4/4+

[@levimarquis1332]

it's not the adapter I had the same problem using the wired method soldering the wires vvdi prog works fine but multi prog couldn't read it multi prog isn't ready yet there also no way of reading eeprom's in circuit like vvdi prog????

[@angelstoyanov6355]

I understood that it is about the version of the adapter. why?? my adapter is also version 1.2 and i never opened the box. Why should I replace it with another one now? How many times will I pay for the same thing. What options do we have for reaction? 4:51

[@daudajalloh6183]

Thanks am about do pay for vvdi multiprog....but after seeing this video and review am not sure i will do it again........so plz between vvdi prog and cgdi which one should i bye........i want to clone volvo xc60 2009 cem module.....

[@lakelandcarkeys]

even when I use my Benz EIS adapters, some times I have to attempt it 2-3 times before it actually cracks. also, try using the prog db cable and see if it makes a difference.

[@pat99UK]

Is your DB version v49 or 4.9 as i'm only on V20 ?? Also My Multiprog seems to have an issue with the MCU Adapter, it will not even identify CAS3+ chip, I have opened up the adapter and it seems to be wired incorrecty, the CLOCK cable GND is not even connected to GND. if I use the Multifunction adapter I can sometimes get it to read using the old 25 pin MCU reflash cable.

[@chrisi1909]

do you maybe have to use the red adapter cable for the Adapter that you used on the PROG ?

[@juht78]

ID: FFFF means, MCU is locked. Thats ok. If U unlock the MCU, then it reads correct ID too ;)

[@salsami6828]

Yes pro

[@rikopli]

Last update database 24.07 and firmware 27.07 FIX IT... !!!!!

[@AutoLockSector]

@rikopli Thank You Rikopli for the Update!

[@jonmaudal7584]

Hello, I am looking at the new multiprog. Please let me know when you get this sorted out. If sucessfull I will buy one. Thanks!

[@AutoLockSector]

Will keep you posted here on the channel.

[@MrSvinkoyaschMrSvinkoyasch]

I happened to read the data from CAS 4+ successfully with my KTP and this very adapter. Didn't have any problems tbh

[@angelstoyanov6355]

What mask is processor? 5M48H or another? Thx.

[@MrSvinkoyaschMrSvinkoyasch]

@@angelstoyanov6355 5m48h, exactly.

[@angelstoyanov6355]

​​@@MrSvinkoyaschMrSvinkoyasch when(this days or before time) you read this cas4+ and what version is your adapter . Thenks you .

[@eurowerx4267]

I’m pissed with their tools. Their support sucks!!

[@sarkhilali4717]

Multiprog fucked my day today..while writing on new Holland ECU tractor...at 18% stucked then timed out and gave me connection failed... and everything gone..

[@jeanleguichard85]

Try to read it now because its successful

[@AutoLockSector]

Just tried it and it still fails to read. Both Versions of the Adapter. V1.2 & V1.3 still no good on the Multi Prog

[@cirilknez1715]

For me VVDI its expensive crap.How many times vvdi make me problems ,wich i than solve with autel. VVdi now sell 13 pieces vag cluster adapter, and for renesas rh850 they not even have develop software for id49-5C key chip. On the end even Keydiy keys work much beter as VVDI. Regards Friend

[@bigo975]

Have u tried cgdi for bmw?

[@AutoLockSector]

I have. I have every tool out there to be honest. It’s about principle. when a company releases a product dishonest ones tend to remove certain features to get the user to buy more tools/adapters in this situation I had done this job before with the same tool with the same adapter and it worked perfectly before they change the cracking algorithm now I’m being told that I have to purchase version 1.3 in order to make it work. version 1.2 worked prior to all the algorithmic changes.

[@DFWAuto_Hack]

@@AutoLockSectorthey did me like rhis before

[@bigo975]

I appreciate your channel, really needed in the space

[@jackgates6949]

CGDI is great and have used it for over a year. But sometimes I just don't feel like soldering up a board so I am trying out the VVDI adapters now.

[@marcin3960]

Vvdi prog is better than multiprog?

[@jackgates6949]

I also have Prog and use the adapter successfully with CAS3. Am hoping it will be good with CAS4 adapter I ordered? I think what he is trying to say is that the algorithm on the Prog is different than other Xhorse tools? It works with older Prog but not the newer tools like Multi?

[@jacktingzon2378]

I should have seen your video before buying this multiprog. I can not read cas4 also and ews4 i can not read also. What the fuck xhorse company is scam with this tool. I hate this tool.

[@Doctor_88]

Its a new tool,waith for updates it will be fix

[@salsami6828]

Vvdi prog good cas 4 and cas plus

[@alexchaveirorj]

Desbloquear cas critografado

[@danielf1016]

Mini acdp

[@AutoLockSector]

I have it all the adapters as well. I just want Xhorse to fix this issue that’s been ongoing, and they ignore feedback, blaiming the user rather than the engineers

[@waldemarfechtel1644]

Xhorse support is very bad.