In this video is shown how to replace timing belt and how to adjust fuel pump
Пікірлер: 28
@MrBenjaminTea3 жыл бұрын
A very clear and informative video, thank you! Greetings from Oxford, UK.
@davidhenderson77224 ай бұрын
Great video 😀
@OFFLlNER2 жыл бұрын
I unerstand blocked fuel pump but camshaft you blocked with key 13 or what? Crankshaft position I see on getriba? Is it same on Audi 80 1.9 tdi?
@mechanicigor2 жыл бұрын
Yes it's the same engine
@aleksandarpesic56352 жыл бұрын
Hello 🙋♂️ please tell me, do you have to take the valve cover? Or you can change timing belt without taking it off, and how?
@mechanicigor2 жыл бұрын
its much more easy to remove valve cover only 3 bolts and you can lock the camshaft
@aleksandarpesic56352 жыл бұрын
@@mechanicigor maybe its easyer, but the reason why I dont want to take it off is rubber seal. I'm affraid that it will leak after. And I was thinking not to take it off. If I choose not to take it off, I should take the engine in TDC, lock my fuel pump sprocket and mark my camschaft, right? Or it is more complicated than that? 😀
@mechanicigor2 жыл бұрын
@@aleksandarpesic5635 you can make it just after installation turn crankshaft 2 rotation clockwise to check alignment
@aleksandarpesic56352 жыл бұрын
@@mechanicigor thank you 🙋♂️
@Gabriel-oq1zg4 жыл бұрын
Hi , Very good video , actually my golf 3 have the injection pump which have two teeth ( clockwise ) difference from camshaft and the crankshaft. However, Camshaft and Crankshaft are aligned perfectly but I cannot insert tool in my injection pump. The problem is that my car has too much advance in injection timing. (advance : 253 instead of 57 in VCDS TDI graph) My question is if I delayed two teeth (counterclockwise), Does this solve the problem that I Have ? I must replace my timing belt soon. Thank you Best Regards
@mechanicigor4 жыл бұрын
I don't know what to say usually if it's miss one teeth the car won't start but two I'm not sure but you can try and if it's not starting than you can return like it was
@Gabriel-oq1zg4 жыл бұрын
today the camshaft and crankshaft were perfectly aligned but I cannot insert timing pin on the injection pump (two teeth before I can insert the timing pin) The car start very well but too much advance and the question was just if I realigned perfectly the injection pump (two teeth before) It solve my advance timing problem ? ;-)
@mechanicigor4 жыл бұрын
@@Gabriel-oq1zg you can try but if the car doesn't want to start then return like it was and try loosen injection pump bolts and try to rotate the pump
@Gabriel-oq1zg4 жыл бұрын
ok @Mechanic for cars thank you I
@mansvardsvaldis68493 жыл бұрын
Good job!
@danjimamamud38795 жыл бұрын
VW all the way
@djemalghem40605 жыл бұрын
Thank you
@ucefkh4 жыл бұрын
well done :)
@sundayoladipupo60422 жыл бұрын
gurf 2, timing belt setting
@ekamatti663 жыл бұрын
No new Waterpump?
@mechanicigor3 жыл бұрын
It was in perfect condition and the owner didn't want to replace it
@dickinson583 жыл бұрын
Българин ли си колега
@mechanicigor3 жыл бұрын
Ne kolega has sum makedonac od koj grad si
@bakiemini34055 ай бұрын
@@mechanicigor dali ushte rabotis so golf imam edno prasanje
@mechanicigor5 ай бұрын
Prasaj slobodno
@bakiemini34055 ай бұрын
@@mechanicigor kako moze da se skine rebrasti kais na golf 3 tdi 90 za 4200 km
@mechanicigor5 ай бұрын
Mozebi ne pravilno zategnat ili los kvalitet posebno ako e Ina vo posledno vreme inata e mnogu los kvalitet