Vw golf mk5 ABS Fault/Traction control warning lights on

Find the items that are used on the Dave Sterl channel in the Amazon shop.
www.amazon.co.uk/shop/davesterl

[@davesterl]

Find the items that are used on the Dave Sterl channel in the Amazon shop. www.amazon.co.uk/shop/davesterl

[@qaziziaulhaque2965]

Explained & diagnosed in professionally manners. 👍🏻

[@subbernh5192]

Nice simple repair, and you are correct about not wrenching too hard on that bolt. I made sure to douche it good with pb blaster first, and used a 1/4in drive ratchet; now the sensor won't come out so I can clean the rust from knuckle before replacing the bearing. May just have to waste the sensor and get a new one. Ty.

[@ballybunnionbhoy]

Nice job and well explained diagnostics and repair, 5 stars mate.

[@wilbardshoopala523]

You sound like Mr bean

[@booneylander]

Great video!

[@bernard.8355]

Great video

[@BobSmith-or5fs]

thanks for this.

[@Gjfunkymonkey]

Love your videos Dave,its nice to watch a norniron man on here👍 can I ask...what type of blue tooth diagnostic machine do yo use?

[@davesterl]

No bother graham, its an autel MS908p

[@sharonebbage1189]

Hi Dave, have you done anything with a brake pressure sensor at all, I've got abs, traction control and tyre pressure lights on but 1 of the codes coming up is 01435, g201

[@r.t.7925]

Thanks for posting . Now I know what's wrong with mine. I put new ABS sensor it fixed it for a few days and now the light is back on :) . I found a video where they sell a kit to replace the sensor , the bolts and the magnetic ring only, not the hole hub . Is it a good idea ?

[@russellmcallister6830]

Dave are crafter wheel speed sensors the same system as this??

[@PH-AUTOS]

awesome video....can i ask...where can i get one of those tools to check the magnetic teeth....

[@asifmalik372]

Pole Sensor Foil from Guys Magnets UK

[@steveacab77]

hi what size are the new alen nuts u use ta

[@LostInDistance]

Great video! I’ve just fitted this myself. Is there anyway of clearing the ABS and traction control lights on the dash without plugging it into a computer? I guess I could pop to a local garage and ask if they can clear them, but some garages get funny and won’t take any liability and won’t help you..

[@dunebasher1971]

They shouldn't need clearing with a scan too, they will go off by themselves when the system detects that the sensor is working correctly.

[@t5jerry]

REALLY useful that dave, got a ABS/ESP light on my 2010 180000k skoda superb, changed the REAR sensor (old 1 had identical) groove in it as yours did, put new sensor in and fault is still on dash, suppose it`s got to be a wheel bearing next ??????

[@davesterl]

Remove wheel bearing and inspect pick up ring, common problem

[@t5jerry]

@@davesterl cheers Dave.

[@99Isopropyl]

I have a 2006 Jetta TDI Manual MK5 and I broke my ABS sensor off when replacing my wheel bearing. The hole that the sensor goes in is quite corroded and I can't get the remainder of the sensor out. Is there anyway to do it without removing the wheel bearing again? I have to borrow the triple square to remove it and I'm worried they'll strip (2 stripped during the removal of the old one and I ended up having to cut the old bearing off with a grinder.).

[@davesterl]

id say you would have to remove the bearing and punch the sensor out

[@catalinvladut3682]

👍

[@conorf8091]

Good video mate. What’s the scan tool name??

[@davesterl]

Autel ms906pro

[@JC-op7fd]

Just got a mk5 gti. Both my abs and traction control lights are on. My esc switch is saying it’s off any suggestions?

[@davesterl]

Get your car diagnosed at a reputable garage

[@richardpreseau7419]

I sent my mk5 GTI to get wheel bearing replaced and now my traction control and abs light is on is that something they could have damaged during the change?

[@clintchrystie6727]

The ring sensor fitted on the hub wasn't fitted so now your speed sensor cannot detect speed. That will actually cause your car to stall and cause a lot of faults.

[@josefelipealvaressalgado2130]

Cómo se llama ese herramienta

[@tahirpatel123]

Hi, I'm getting error 01130 ABS operation Implausible signal. I clear the codes but as soon as I drive, the hand brake light flashes, the ABS light and Traction control light stays on. Any ideas?

[@dunebasher1971]

That's either a faulty sensor or a faulty magnetic ring or both. Although 2 years on, I suspect you've long since dealt with the problem.

[@travellman2502]

My Passat abs light n traction light on i check the dtc p00287 ,3842 is coming rear rh abs sensor fault coming ,fisrt I changed the sensor but still the same fault is there after I check the voltage it's 11.76 coming,what is the next step pls help me

[@travellman2502]

What is the prblm pls reply it's urgent

[@farmerjohn418]

What scan tool do you use

[@davesterl]

Autel maxysis 908p

[@chumps7974]

The tip of the sensor and the fastener broke. Is there any way to fix?

[@davesterl]

I think you'll have to replace it

[@chumps7974]

@@davesterl replace the whole knuckle? I guess I'll start looking for a brand new one

[@lornemalvo3298]

it was more a bearing issue than a sensor issue?

[@dunebasher1971]

The corrosion on the bearing damages the sensor. The two issues are intertwined.

[@artem903852]

Че он сделал, как Починил?

[@user-xj8nv1lr1x]

ступицу заменил

[@danielallard6378]

My guys just charged me 170 pounds didn't get a aftermarket as he says it not as good . And took wheel off to clean behind and the pick ups ???

[@DWAC.00]

If the cars on a hoist, why not put it in drive for a brief moment so you don't have to spin the wheel by hand. Ty for this helpful video btw

[@davesterl]

The car is front wheel drive and this is a rear wheel. This car has manual transmission. Thanks