Well done. I enjoyed the series. I have been out of the hobby for 35 years and recently started up again. I use to fly glow and starting back up I decided to go all electric. Your videos reinforced that decision…thanks
@hayloft38345 ай бұрын
Did a similar thing and now the old smells are starting to welcome. On the way to a mix of both.
@carycary58245 ай бұрын
I think I’ll buy an RC plane. Looks like fun. I use to fly a real Piper years ago but my buddy moved to California and haven’t flown in years. This would be the next best thing. Thanks for the video!!!
@autogyro3335 ай бұрын
Do it, I'm 51yo and started 3 years ago thinking I could never do it. 3 weeks ago I was 3rd in my first F3A c-ish club competition, out of 5 contenders but still not last. You will love it.
@ah4quadssake8854 ай бұрын
Have you checked the clunk in the tank? ,that might explain why it konks out after a short while
@SomeGuyInSandy5 ай бұрын
If you peak the engine on the ground it's going to unload and run lean in the air. It'll get hot and stall. Peak it and then enrich the high speed needle (turn it counter clockwise a few clicks) so that the engine drops a couple hundred rpm then you should be good.
@robertcovell27875 ай бұрын
Exactly!!!
@Syphronix5 ай бұрын
incredible deadstick!
@dongordon44645 ай бұрын
So why do you think you need a music track?
@alleycat54724 ай бұрын
Yes indeed shorts brought me here :) Good job.
@Hangar14RC4 ай бұрын
That's awesome! thank you!
@jameslester38614 ай бұрын
Flukey glow plugs can be tricky to diagnose sometimes and fuel that is too old. It’s been over 20 years since I built a kit. The last one was a Topflite Contender and I still have not flown it. All it needs is balancing and a thorough radio/battery check. I bought the radio new in 2000, cycled the batteries a couple times. It’s still I. The box under a bed. I have been looking at foam board building and may try building a Stik witch electrics instead of glow power.
@philtheoccultist5 ай бұрын
look at gels man so inspirational
@johnnichol94124 ай бұрын
That wasn't a walk of shame, nailed the dead stick landing perfectly from the glide to the landing. Apart from a slight walk that is but no shame in that..
@chrisross79365 ай бұрын
Do you have the fuel tank wrapped in foam? If not the fuel can sometimes foam and cause it to lean out in the air causing flame outs. Nice dead stick landings!
@Hangar14RC5 ай бұрын
There is some! But could probably use more. I honestly did not think about that. Thanks for the tip!
@chrisross79365 ай бұрын
@@Hangar14RC No problem. If you see tiny air bubbles in your fuel line to the carb , the tank is probably not isolated enough or there is an air leak somewhere in the system.
@fliegerdefunes77583 ай бұрын
The backwards starting is a thing some engines do mostly new engines but it yea idk thats weird. my guess ist still the fueltank but its hard to judge over the internet and I'm on the other side of the ocean XD. But I think I have to start to post again. I bought good Equipment to film my planes but I never really tried it out for a video just didn't had the Motivation. Maybe ill find it in the next few weeks :) Oh and btw what size of engine is it?
@Elisrc.5 ай бұрын
Awsome video👍👍
@Hangar14RC5 ай бұрын
Thanks 😁
@tboystoys56825 ай бұрын
See that’s what we lack around here a flying club because I’m on my own it would be great to be able to get some help from some more knowledgeable people when you run into a problem
@zekeharley5 ай бұрын
lose the music and sound effects and you'll have a great video
@samnugent34805 ай бұрын
A $100 bucs even if the motor is wiped it's still a bargain , but hey it might come down to a new carb maybe the seats crushed
@FarmerFpv4 ай бұрын
That start-up is way too easy. Have you checked the compression? It seems like it has low compression. Especially if it is starting backward that easily. Yes, they can start backward but that mostly happens in low-compression engines. I would check. If it is low you can always have the sleeve pinched to get more compression out of it. It will always lean out when it gets warm during climb out. If the compression is good then the high-speed needle is too lean. Turn it counterclockwise a turn or more. It should have more smoke coming out of the exhaust. It is not getting enough fuel. Rich is better than lean. It just won't produce as much power. Too rich is not good either but you are not having that problem. The smoke seems really light. Good luck. If anything the airframe is worth the $100.
@donsebestajr17144 ай бұрын
Probably got a small hole in fuel line!
@harveynewman43334 ай бұрын
is that a OS,AX,motor? if it is,replace it . they had issues with cylinder plate peeling. also the remote fuel needle valve, sometimes had problems. put a os,fs 70 or fs 91.perfect motor for it.
@johnnichol94124 ай бұрын
Well there you go, the most popular motor by far at our club OS .55 AX and nobody seems to have issues. Apart from one who thought the engine was a bit rough, then he tightened the plug and issue solved.
@harveynewman43334 ай бұрын
@@johnnichol9412 ask him to remove the cylinder head and inspect the bore for peeling. it can cause a rough feeling during hand cranking. i have some of those laying around,needing the same parts.
@johnnichol94124 ай бұрын
@@harveynewman4333 After tightening the plug and problem solved?
@daviddou14084 ай бұрын
A .91 for what appears to be a 1500/1600 Cub? Built fairly lightly in balsa and film by the looks, it isn't a Cassut Special.
@Fishing81365 ай бұрын
Fuel tank breather to restricted😎🇨🇦
@PockoRC5 ай бұрын
its 2 stroke glow, it doesn't have a breather... either glow plug, a pin hole in a fuel line or tank location. I suspect the clunk line has a split in it
@Fishing81365 ай бұрын
@@PockoRC hope you resolve this, looking forward to a full flight😎🇨🇦
@PockoRC5 ай бұрын
@Fishing8136 not my model. just saying what I think the issue is
@johnnichol94124 ай бұрын
@@PockoRC If it doesn't have a breather/exhaust pressure then the tank is going go negative pressure thereby restricting/cutting fuel flow.
@lasersbee3 ай бұрын
Is that the one you started building 4 years ago ? Never saw another Build video after that.
@Hangar14RC3 ай бұрын
Unfortunately not. That one is still sitting on a shelf waiting to be finished!