How do you score a discount on the third tool? Thanks
@Hindsight1012 жыл бұрын
@@enriquejimenez6088 because I have a KZbin channel and I did a video on it
@rockgoleu2 жыл бұрын
So right, first tool made from weak a Aluminum. First use on a tough stick 1222, and also last use.
@dinokadric95912 жыл бұрын
Sorry, I figure out. One piece of plastic got stucked in pipe and that's why I couldn't push further. I fixed that one. Thank you very much ! Dino
@Hindsight1012 жыл бұрын
Welcome
@cindyday8802 жыл бұрын
Single mom here. Hiring a plumber just wasn’t in the budget so I tried to change the shower cartridge myself. Of course I had an old cartridge that was Very stuck even with the Moen tool. I couldn’t get anything to work. I watched your video and using the tool with a wrench, was able to finally get the old cartridge out! Thank you for your expertise, great video!
@Hindsight1012 жыл бұрын
Wow thanks for the comment
@terrymorton4314 Жыл бұрын
Mine was removed from a calcified 20 yr install. The Danco tool worked for me after watching this video showing how to properly use it. I also sprayed some loosener and just slowly got it out. When I went to install the new one, I cleaned the valve tube, but the calcium had built up so much that I couldn't insert it. Since there was no turning back, I sat patiently with CLR and a small steel brush and worked out the gunk. Once the new cartridge would slide in without excessive force, I got the clip back in and wrapped it up. Thank you for this great video👍
@Hindsight101 Жыл бұрын
You're welcome and wow that sounded like a pain
@mKierstenk3 жыл бұрын
My parents had been using a wrench to just turn their cartridge stem for years after their handle broke. So the stem itself was smashed and unable to thread a remover into it. After applying heat using a hair dryer for 15 minutes (and an additional 10 minutes when it still wouldn't budge), the cartridge basically slid right out. I wish the puller could've worked for their cartridge, but I wanted to mention the heat in case it helps anyone else.
@Hindsight1013 жыл бұрын
Thanks
@TCh39622 жыл бұрын
We are regreting using the heat technique. It caused the plastic to break and the stem to come out, leaving the rest of the plastic and black rubber parts stuck inside and nothing for us to get leverage on to get them out.
@snarebucker16072 жыл бұрын
Hair dryer helped a lot for me. I had the new valve w/ included nylon tool - old valve wouldn’t move a bit. I also had the danco puller; but didn’t want to force it if it was that seized up… saw a lot of nightmare scenarios where the puller failed and broke the valve. Hair dryer for 15 mins - then tried the nylon tool - valve moved a little bit. Immediately used the puller and it slid right out.
@amberhankins41062 жыл бұрын
My cartridge is still stuck with this tool. I’m about to use this method and hope it works!
@mKierstenk2 жыл бұрын
@@amberhankins4106 good luck!!
@platinumchaos57852 жыл бұрын
What a great video. You have a nice speaking voice. You're easy to understand. Thanks!
@Hindsight1012 жыл бұрын
Thank you
@CITYBORNDESERTBRED7 ай бұрын
Maaaan, that Lakeview Puller is the business. You put me up on game. Brandon goes into the manufacturing of the product, how to use and care for the tool.. when I called the company, BRANDON picked up the phone, unheard of in this day and age. Even shipping was a day faster than Brandon assumed. Awesome product and great service. I spent 2 days trying free a stuck cartridge. My property has at least 10 other units that I feared would’ve been the same struggle, but now with the Puller, I’m looking forward to the task 💪🏾
@Hindsight1016 ай бұрын
Happy to help
@cdee60963 жыл бұрын
Wish I knew about the ona puller before. I just melted out my cartridge with a torch and it was not fun. Thanks for your video.
@Hindsight1013 жыл бұрын
I wish I knew about it before I removed a dozen or so myself. Thanks for watching
@davidater92 жыл бұрын
I am going with Ona, although Lakeshore looks like a winner if you do a lot of these moens. I agree with your comment on Danco replacement cartages being bad...I have tried them several times over the years and they all started to leak within 6 weeks.
@Hindsight1012 жыл бұрын
Let me know how you like the Ona
@davidater92 жыл бұрын
@@Hindsight101 I tried an Ona out on a stuck 1222 Moen stem - rubber out of position. The Danco couldn't get it. Ona work great. It took about 2 minutes.
@Hindsight1012 жыл бұрын
The ona is probably my second favorite
@juliebrown8375 Жыл бұрын
Excellent video. I wish that I had watched this one before I removed the valve. Your demonstration was much better than the instructions in the package. Since I'm a little old lady, I also used the Danco puller to push the new cartridge back into the valve. I hope I don't have to do the other bathroom anytime soon.
@Hindsight101 Жыл бұрын
Hey! Great job for trying something new
@rafaelgriffogoes4322 Жыл бұрын
Used the first tool on a VERY stuck cartridge, and it was a hassle. One thing that worked for me was that once the big nut on the removal tool was no longer useful, I took the remover tool out and used vice pliers on the cartridge white plastic body. After a lot of wiggle and pull, it came out. Parts of the rubber of the old cartridge were stuck inside, so I need to clean up a bit (nose pliers, paper towel, etc). This video shows how things works, very useful for first timers, thanks!
@Hindsight101 Жыл бұрын
Welcome
@spektor5611 ай бұрын
This was my exact experience, I had to get all the stuck rubber pieces out of the inside of the pipe after I managed to pull it out with pliers. I live in an area with hard water (I do have a kinetico softener though) and had to replace the cartridge on a new home that is only 7 years old.
@Hindsight10111 ай бұрын
Ugh
@FrankSouza-ss7cz Жыл бұрын
Thanks so much, Your video saved me a hell of a lot of problems. I had to get the place ready and i was sweating. No puller, amazing.
@Hindsight101 Жыл бұрын
You're welcome!
@rodgerstcr Жыл бұрын
Pulled my 1222b cartridge out using screw with lever method. Had to remove the plastic sleeve using a 3/4 inch tap and bolt with washers to screw the sleeve out.
@Hindsight101 Жыл бұрын
It's definitely one way to go
@Christy.12 жыл бұрын
Thank you for this, wish I would've seen it before hand. I used the Danco puller, it's all the store had. Actually tried to read the directions too, but they sucked. And on my faucets, double bath tub faucet, I didn't have a copper pipe sticking out like that, mine was just the plastic piece of the cartridge. So you helped with one, I started using the nut on it to pull it out, and it helped loosen it. The other side, I messed up the plastic and it took me a good hour of just wiggle/pull/wiggle/pull with every tool I had handy. Now, I'm having a hard time getting the new ones in fully. Just a slight gap, they won't budge any further. And putting the handles on...OMG lol. I'm so disgusted, I'm not even going to bother turning the water back on, I'm just going to bed and deal with it tomorrow.
@Hindsight1012 жыл бұрын
Do you know the model faucet you have? Someone else had the same kind of cartridge and had the same issue. I need to know the faucet model or cartridge model. Thanks
@Christy.12 жыл бұрын
@@Hindsight101 Oh thank you so much for answering :) Well, no idea what the model is for the faucet, it looks like the Moen Adler Two Handle Bathtub Faucet, the cartridge part was I think 1244. So, after my little fit there, I got up next morning, all refreshed. Took it apart, and I guess putting it back together and screwing the handles back on was enough to make both cartridges go in all the way! I'm guessing it's something to do with the handle screw, but all that plastic, just kept making me nervous constantly screwing in/out. And, the handles are totally out of whack. Instead of turning on from outside to inside, one goes up and down, and the other is at an out to in angle. And I don't care one bit, because they turn off and on, and do not drip when off :) Oh, and I found this link if it helps you at some point or someone else; last picture has all the parts in order. The adapter that's circled, goes into the wall tube in front of it (my tube's brass) apparently there's an o-ring on the adapter, but it was stuck in the tube. I think that's why I was having a hard time with the handles, they just seemed loose and wiggly. Anyway, thank you again!! terrylove.com/forums/index.php?threads/new-moen-82602-2-handle-cartridges-seem-faulty.96718/#
@easyhomesearch Жыл бұрын
Thank you so much. This was so clear and detailed.
@Hindsight101 Жыл бұрын
You're welcome
@darrinj7937 Жыл бұрын
So the easiest cheapest way for me after snapping the brass shaft, was drilling a hole ~.25" deep. Then I put a construction screw, similar to a decking screw, getting it as straight as possible. I put the torx/star bit in my dril, not my impact, select high speed and turned the screw/brass full speed until I saw smoke 🤔 or steam and continue 20-30sec after that point. You should hear it sizzling, then grab the screw if secure enough or the cartridge if you have narrow grippie pliers and it slides out with ease. I was surprised because it was a plastic cartridge, but this did the trick. Next time I get a stuck one I'll cross thread a screw into the shaft(instead of snapping it pulling&prying) and spin-cook it until it's well-done.
@Hindsight101 Жыл бұрын
Thanks for the info👍
@wayne9903 Жыл бұрын
YOU ARE DA MAN!!!!! Excellent instruction! Made the whole thing easy as PIE!! Thank you!
@Hindsight101 Жыл бұрын
Welcome
@GaryYoung-eq1ph Жыл бұрын
Easy newer cartridge !!!
@JRoss7072 жыл бұрын
My stem broke of as I was trying to twist it out. I ended up drilling it out with a 3/8” drill bit, first all the metal components in the middle, then the plastic casing walls. It was a laborious process and took a couple of hours. Of course it was a weekend, and the water had to be shut off, and I worried that I’d actually damage the Moan valve, which would be beyond my expertise to replace, plus I’d probably have to cut into the wall to replace it, either from the outside of the house or remove shower tile. Luckily with a lot of patience and persistence I got it all out.
@Hindsight1012 жыл бұрын
That does not sound like fun
@TheDavidarlen Жыл бұрын
Thanks I have not seen the Lake view puller before. I will check into buying a couple.
@Hindsight101 Жыл бұрын
Its expensive but worth it
@caseyhartman7094 Жыл бұрын
I want to change the faucet in my condo unit. I am pretty sure the tub, faucet, and spout/diverter are original from 1982. I am going to get one of the pullers and hopefully the cartridge will come out fairly easy.
@Hindsight101 Жыл бұрын
Good luck
@a1b9e7l6 Жыл бұрын
Nice video. I didn’t need any of the tools. My cartridge pulled out pretty easy. I had the most trouble with the darn set screw for the 🤬 handle.
@Hindsight101 Жыл бұрын
interesting I have never had that issue
@mdear2010 Жыл бұрын
thanks for the video. I wish I would have found your video before I removed mine. I almost couldn't get mine out. thankfully I didn't damage anything.
@Hindsight101 Жыл бұрын
Hey at least you got it fixed
@richardberryhill718 Жыл бұрын
Well done! Nice and clear, good explanation.
@Hindsight101 Жыл бұрын
Thanks
@serdgeedgerunner9 ай бұрын
I use moen cartridge removal and cartridge cracked inside and I been able to take out only half.
@Hindsight1019 ай бұрын
How's it going
@chuckbower21 күн бұрын
what happens when the brass core comes out? I now have a plastic sleeve stuck inside the stem.
@Hindsight10119 күн бұрын
try this video kzbin.info/www/bejne/eZfEemtsfsiZkM0
@mhw313 Жыл бұрын
This is the single most helpful video I found for helping get out a stuck 1225 cartridge. Thanks so much for making my first foray into plumbng a success!
@Hindsight101 Жыл бұрын
You're welcome!
@cordeliabriar29247 ай бұрын
When I finally got my help. And I put the new one in now. It's stuck just maybe half inch away from going all the way in. And I can't move it at all.
@Hindsight1017 ай бұрын
There might be some build in there and you can take a wire brush or something to clean it out. Just remember to run some water to flush everything out before putting the cartridge back in
@arthurgoshey2287 ай бұрын
Can’t thank you enough! Saved the day.
@Hindsight1017 ай бұрын
You're welcome!
@420 Жыл бұрын
1:06 - RIP - just bought the Danco cartridge for $39 vs the Moen $54.
@Hindsight101 Жыл бұрын
In my experience they use cheaper materials so they don't last as long and when you try to remove them. They can be a nightmare because those cheap materials get stuck
@rodgerstcr Жыл бұрын
In my case the brass stem broke off inside the cartridge;any suggestions? The ona puller doesn’t fit in the small hole left by the broken stem. Great video, thanks.
@Hindsight101 Жыл бұрын
Take a look at the links in my description to other videos. They may help
@enriquejimenez60882 жыл бұрын
Hi, thanks for the video very informative on the 3 different tools. I wonder if you could use a power ratchet for the last tools.
@Hindsight1012 жыл бұрын
You could if it is powerful enough, if not then just do it manually
@richardwilk18972 жыл бұрын
great video..ordered the Lakeview tool...thank you,,,
@Hindsight1012 жыл бұрын
Awesome it's always good to support local
@DaMacy19895 ай бұрын
Screw broke off in brass piece so i cannot screw any of these into it. Really stuck.
@Hindsight1015 ай бұрын
This video might help kzbin.info/www/bejne/eZfEemtsfsiZkM0
@derrithnelson8745Ай бұрын
Thank you! Seven blood blisters later on my 1-67th attempt to get it out before buying this tool.
@Hindsight101Ай бұрын
@@derrithnelson8745 which tool did you go with?
@stanleygibson1257 Жыл бұрын
I see a lot of people pulling the stuck cartridge out. What happens if you remove the retainer clip, throw a towel over everything abd turn the water on for a couple of seconds? Would water pressure push the cartridge out?
@Hindsight101 Жыл бұрын
Probably nothing. You'd have to have a lot of water pressure
@AlexGarcia-hn6sw2 жыл бұрын
Hi I would like to know where can I buy the lakeview puller ? Your video is very helpful thanks for uploading
@Hindsight1012 жыл бұрын
Usually you can check the description of the video but here you go and let them know I sent you lakeviewpuller.com/
@JenniferKuhns3 ай бұрын
I'm trying to remove the handle itself, which is stuck. It won't slide off like yours. I'm worried about causing more damage if I put more force into it. Any advice?
@Hindsight1013 ай бұрын
Did you remove the screw holding the handle in?
@JenniferKuhns3 ай бұрын
I did. I feel dumb, but here's what worked: turning the handle back to the off position. Then I was able to jiggle it off. Thanks!
@Hindsight1013 ай бұрын
Hey awesome, at least you got it off
@baddad57816 ай бұрын
Excellent video thanks
@Hindsight1016 ай бұрын
Thanks
@soulv2568Ай бұрын
First method worked for me. Plastic was broken from inside
@Hindsight101Ай бұрын
Thanks for the info
@GEAE_Denny_L Жыл бұрын
A small broken piece of the old cartridge plastic still stuck at back of the hole surrounded by hard water deposit. Trying to chip it out with screwdriver, and hammer. Also, trying to figure out what replacement cartridge to buy.
@Hindsight101 Жыл бұрын
Can you lookup the model of the faucet?
@GEAE_Denny_L Жыл бұрын
@@Hindsight101 ~ Decided to call in a plumber to replace to avoid damage to the plumbing or water leaks going downstairs.
@Hindsight101 Жыл бұрын
@@GEAE_Denny_L 15.4K subscribers Hey I get it. I still call a plumber if I think I could damage something more than its already broken.
@BheemReddy8 ай бұрын
I have Broken Head .. How to puul with this Tool ? I cannot screw as
@Hindsight1018 ай бұрын
The second tool should help with that, if not check out some of the videos I have linked in the description of the video
@charlesjuett74456 ай бұрын
Bruuuuuhhhh I was looking like you trying to pull it out 😂😂😂
@Hindsight1016 ай бұрын
Then thumbnail did its job lol
@charlesjuett74456 ай бұрын
@@Hindsight101 thank you for the video. I bought the tool you showed first I believe from Lowe's and it pulled it out in a couple turns.
@amberhankins41062 жыл бұрын
This video was the most helpful, but I still can’t pull out the cartridge. What else can I do?? HELP!!
@bsatchel7052 жыл бұрын
Maybe the rubber grommet has started peeling off...? I just fixed mine today. I was able to brace the fitting inside the wall, then I pulled like crazy. It took about an hour of pull, wiggle, pull, wiggle. I'm not sure wd-40 helped, but I used it.
@Hindsight10119 күн бұрын
thanks
@divetothesky Жыл бұрын
Thank you so much.
@Hindsight101 Жыл бұрын
Welcome
@dalemihocik47324 ай бұрын
I must disagree that the supplied tool with the cartridge is useless and should be thrown away. To use it correctly place the tool over the cartridge and twist back and forth several times to break the bond between the pipe and the cartridge. With just a little patience and persistence it works just fine for me, and I've replaced many a cartridge over the years.
@Hindsight1014 ай бұрын
I do understand what you're saying but if it's really stuck and I've had a few that white piece isn't doing a thing
@steveh.9166 Жыл бұрын
great info. thanks
@Hindsight101 Жыл бұрын
Glad it was helpful!
@bryanlenkowsky90302 жыл бұрын
Bought a Moen puller off Amazon but the teeth don't fit around the white piece. White piece is a bit too wide. Any idea?
@Hindsight1012 жыл бұрын
What model number is your cartridge? Also did you get an off brand or did it say it was moen?
@christina_blessedbeyond Жыл бұрын
what do I do if the cartridge plastic broke while pulling it out? I now have half the cartridge stuck and it just seems to not want to come out. I don't want to replace the whole valve....
@Hindsight101 Жыл бұрын
Some people suggest using heat. I've had to break pieces out one at a time. There isn't one set way
@samgirgis7368 Жыл бұрын
What tools you used to break it piece by piece. Greatly appreciated
@MrsRamon426 Жыл бұрын
And what do you do if it's stuck AND that little brass nub broke off?
@Hindsight101 Жыл бұрын
See the video description for other ideas that might help
@criscastaneda82412 жыл бұрын
@hindsight101 what if the brass piece is broken, will tools still work?
@Hindsight1012 жыл бұрын
this might be an option kzbin.info/www/bejne/jp6ll2eFZs2AaM0
@spewgilist2 жыл бұрын
This is what’s needed, the moen only presses a short distance and then you’ve got yo work it out by pulling.
@Hindsight10119 күн бұрын
thanks
@eduardorodriguez-ei4mw2 жыл бұрын
thank you very much
@Hindsight1012 жыл бұрын
Welcome
@systemoperator77927 ай бұрын
Great video. Just remember to remove the pin holding the cartridge in place. Otherwise all the effort is for nothing. :)
@Hindsight1017 ай бұрын
Thanks this is explained in my original video
@priscillaarbanas51252 жыл бұрын
What if the screw is stuck without a head?
@Hindsight1012 жыл бұрын
Are you sure you just don't need a small Allen wrench to take that screw out?
@davidsmith46549 ай бұрын
I like the last tool that seem really nice and heavy duty and strong.
@Hindsight1019 ай бұрын
It is great
@robertmartinez50868 ай бұрын
HOW DO I BUY ONE OF THOSE LAKEVIEW SHOWER CARTRIDGES PULLER INVENTED BY BRANDON ?
@Hindsight1018 ай бұрын
Always check the description of the video but here you go lakeviewpuller.com/home/
@sauleomarova7730 Жыл бұрын
Excellent! Thank you for your video!
@Hindsight101 Жыл бұрын
Welcome
@mikemazzoli19902 жыл бұрын
Not gonna lie I almost had a hart attack when I saw the price of that lakeview puller! IMO its over priced for what it is, not really worth having laying at the bottom of my tool bag, but when i have time i may try to fabricate one like it just for fun
@Hindsight1012 жыл бұрын
it is expensive but after dealing with a stuck cartridge and it will pay for itself compared to the time wasted or the cost of a plumber
@charlesromney Жыл бұрын
Someone knows where to buy the screw of the moen tool?
@Hindsight101 Жыл бұрын
It's a standard screw. If you have a hardware store nearby you can pick up a replacement
@charlesromney Жыл бұрын
@@Hindsight101 I found it , Thanks anyway! The screw is #10-24 x 2-1/2in.
@gt-c-2 жыл бұрын
so many tools only to pull a cartridge...?
@Hindsight1012 жыл бұрын
what a great time to be alive
@jdear97 Жыл бұрын
well done
@Hindsight101 Жыл бұрын
Thank you
@mikegimenez2629 Жыл бұрын
You forgot to mention to remove the retainer Circlip.
@Hindsight101 Жыл бұрын
It's in my full installation video linked in the description
@mmhsn07 Жыл бұрын
Wrong use of the tool. Read instruction to use it correctly.
@Hindsight101 Жыл бұрын
Thanks
@kwame57742 жыл бұрын
Why put out a video on the Moen cartridge puller without showing removal of the cartridge to complete the job? If you want to test other tools, put them on separate video. You aren't going to gain a large following recording a job done halfway.
@Hindsight1012 жыл бұрын
You are more than free to record your own videos
@bsatchel7052 жыл бұрын
Getting the thing out is 90% of the job. Hell, instructions come with the new one...
@Hindsight1012 жыл бұрын
Thanks for watching
@alicepooper85629 ай бұрын
Get your screw gun and a 3in wood screw, screw it into the cartridge beside the stem the screw will hit the stainless steel inner cartridge and push the cartridge out your welcome that will be 300 bucks
@Hindsight1019 ай бұрын
Thanks for the info
@Sendnuddiez9 Жыл бұрын
🫡🫡🫡
@Hindsight101 Жыл бұрын
Welcome
@MccCoke2 жыл бұрын
Guys and Girls! I just fixed a 20 year old pipe with the first option. You have to use a rust remover (not wD40) the cheaper “specialized for rust) worked perfect. I sprayed the surrounding pipe. Used the puller wiggled it left to right while pulling (not too hard) took out the puller, added more rust remover, and repeated the process until it loosened up. It takes patience, will save you time from having to break the pipe.
@Hindsight1012 жыл бұрын
That's for the tip
@SonnySumampong-w1w9 ай бұрын
I agree to spray it with silicone spray before doing the pulling with Moen Tools, make it easier to slide out.
@republicforever9462 жыл бұрын
The real fun starts when the little rubber grommets peel off inside the valve body...
@Hindsight1012 жыл бұрын
had that happen before
@johnhawkins55132 жыл бұрын
Great videos both the first and this one. This one, though, really clarifies the cartridge removal process and showcases good tools. Today, I removed a Moen 1222 cartridge and got by using the white plastic provided spanner. Worked using slow, steady force. These instructional videos are awesome!
@Hindsight1012 жыл бұрын
Glad it worked out
@michiganmom49707 күн бұрын
Don't bother buying a puller. Just drill a 7/64 hole in the plastic part of the cartridge (either above or below the stem location), screw a screw part way into the hole, then use the claw part of a hammer to pull it out. Use a wooden board to provide leverage and protect the tiles from breaking. Cheap and easy!
@Hindsight1012 күн бұрын
cheap yes easy I would have to question
@JScaggs212 жыл бұрын
I bought the Danco core cartridge remover and it still wouldn't budge. I had to remove it piece by piece and yes it was a nightmare. Thankfully, my resolve won out.
@Hindsight1012 жыл бұрын
Glad it worked out
@MrWatchingthetube1 Жыл бұрын
Thank you for making this video!!! As I write this it is ten at night, I have guests (my parents) visiting, and I have to shut off all the water to my house because of one flow control handle. I have had to sort through a TON of noise before I found your video. I am grateful that you were so thorough and informative. Im confident I can get what I need done tomorrow.
@Hindsight101 Жыл бұрын
Let me know how it goes
@MrWatchingthetube1 Жыл бұрын
@@Hindsight101 worked perfectly... and with the information gathered I didn't even need to get the extraction tool. Thanks again and keep up the good work.
@Hindsight101 Жыл бұрын
Thank you glad everything worked out
@robertfanjoy99882 жыл бұрын
After ordering one of the recommended tools, grew impatient and tried the plastic tool included with the cartridge. It worked great. Guess the cartridge only needed a little nudge. Without the video, I would never have figured out the purpose of the white plastic piece. Assumed that it was an ill-fitting cap.
@Hindsight1012 жыл бұрын
Well I'm glad the video kind of helped. Thanks for the comment
@prepparig144 Жыл бұрын
You saved my life!! Or at least a couple of hairs on my head. Both your install and how to remove a stuck cartridge. Home Depot only had the Danco, but it worked. At first I thought it wasn't because my daughter didn't tell me she was having issues and ground those black rubber ovals down to shreds. So, when I was trying to get unstuck, it sounded and felt awful when tightening. But I watched your video again and just gave it a few more twists and it started to some out. Only thing I didn't see in yours or other videos was the pin. I was assuming it went around the cartridge but after rewatching, I was able to see some movement of the pin in front of the cartridge. But love how you explain step by step with some extra details, but no fluff. I went with the Moen in instead of the ACE or the Danco; works so smoothly. Thanks a bunch!!! I'm gonna start listening to more of your videos to see how else you can make my life easier!!!
@Hindsight101 Жыл бұрын
Thanks for the comment and glad I was able to help
@sergioramirez4511 Жыл бұрын
Fantastic video and I bought both the tool (Danco core puller) and cartridge at Lowes the tool was $16 and the replacement was $58, and only took a few turns to push out. No need to buy the grease, it comes with a small packet in the kit. To take the tool off, losen the bolt first and the the top screw will come off the tool for reuse. I am now my neighbors expert plumber for these units. Since most of the homes in my area are only about 7 years old and others have been having the same problem and I easily saved $200 to $300 by not calling a plumber. I am a youtube engineer and proud of it, from plumbing, electrical, gardening, putting my back in place and keeping my 3 vehicles running. Thank You. ( Just remember to read the numbers on the top of the cartridge to find the correct one at the hardware store and remember to turn off water and release the pressure on the shower valve first and be ready to put a towel under the pipe, because you will still get some water popping out and you don't want this to run down the back of the wall. Plus, plug the drain, so no screws fall down, also use the plastic part to push in the new cartirdge)
@Hindsight101 Жыл бұрын
Thanks
@fgerstenberger Жыл бұрын
Great video on how to use the Danco tool. The written instructions were terrible. This video helped me get it done.
@Hindsight101 Жыл бұрын
Glad the video helped
@appa324729 сағат бұрын
My problem is. I got the moen handle off. But now theres a black piece of plastic with the stop, I guess and its stuck. Cant get it off to pull the white plastic out to get to the cartridge. Dont want to break the pipes but I tried lube wd40 and tapping in it. No luck
@Hindsight1018 сағат бұрын
Would you take a picture and email it to me so I have an idea of what you're talking about?
@gunzborgia14038 ай бұрын
My shit is really stuck
@Hindsight1018 ай бұрын
So were you able to replace the cartridge?
@davidy4982 жыл бұрын
Very useful advice and tools but I do not recommend the first one for corrosion cartridges, it was extremely wedged and it broke off a piece of the bolt inside because it's kinda, now I'm trying to look up how to remove the broken bolt inside or none of the tools will even work.
@Hindsight1012 жыл бұрын
There is a link in the description on how to possibly help with your issue
@davidy4982 жыл бұрын
@@Hindsight101 The piece of bolt is broken inside the stem and not the top part, I can't stick anything in there which is what all the tools need and I don't want to take the whole stem off and leave the cartridge in the to be pulled out bit by bit, I'll look for an answer somewhere, thanks for the reply
@3480eric4 ай бұрын
Good video. I have struggled to get many of these cartridges out. Now I know there some good tool options that make the job much easier.
@Hindsight1014 ай бұрын
Glad to help
@rodgerstcr Жыл бұрын
My 1222 B came out and left the plastic sleeve in the pipe. I thought the ona puller would pull the sleeve out using the 2nd function you talked about. It was not big enough to grab the plastic sleeve on the 1222; it is sized to work on the other Moen cartridge (1220 I think).
@Hindsight101 Жыл бұрын
Thanks for the info
@rejeanpaquet43753 ай бұрын
I'm removing the Moen 1222 cartdrige and having problem, it's stuck, I came here for solution, i have the 1st tool and it's not working. I feel I need the 3rd tool but it's too much money for a 1 or 2 times use, but if I was a plumber I would get it, so easy. So I'm still looking....
@Hindsight1012 ай бұрын
Good luck
@ricardocuellar4760 Жыл бұрын
Changed mine yesterday. Took a pair of needle nose pliers to turn the cartridge. Then pulled it out with some channel lock pliers.
@Hindsight101 Жыл бұрын
Awesome
@joemc1115 ай бұрын
my 1200 broke off so I got a plumber he used That tool and it broke part of the cartridge off and we had no way to get it out, he cut the whole valve out and put a new moen in. Since then I watched a lot of videos. One guy uses a 1/2 die, he makes threads in the old cartridge then uses a 1/2 bolt the remove. I got the old one and I gone to get a die and try it.
@Hindsight1015 ай бұрын
I have a video linked in the description that demonstrates that method
@down4thecause4 ай бұрын
if the screw from the handle is broken inside the cartridge, can one tmof the pullers still be used? any suggestions?
@Hindsight1014 ай бұрын
You will need to find a way to extract that screw. They do make extractors for stuff like that. Just find one that's small enough
@TheDannyB967 ай бұрын
Hey man, I was able to pull out , but now it won’t go in smoothly. Any tips? I’d appreciate it man!
@Hindsight1017 ай бұрын
There's probably some buildup if you can take a wire brush in there and kind of scrape some stuff out and then once you're done run the water through it to flush any of that stuff that you scraped away off and then try to reinsert the cartridge
@rower412 жыл бұрын
Very good. I think the basic puller (Danco for about $20) causes more problems than it solves as I've seen a few folks break their cartridges with this puller. The ONA seems like a great idea but it a bit pricey considering you'll likely only use it a few times in your life and then lose it ;-). For pros it would be great. I decided to just call a plumber when I had mine badly stuck... just didn't want to cause a bigger problem and even more expense. Great video! Thanks.
@Hindsight1012 жыл бұрын
thank you
@titovs2100 Жыл бұрын
The Danco Tool failed me. The Screw Head stripped. The metal is very soft.
@Hindsight101 Жыл бұрын
Yes they are very soft. I dont know why
@DaMacy19895 ай бұрын
Mine broke off inside too! What did you do???
@TAX35726 күн бұрын
Put the Blow Dryer On It!!! 💯💯💯🤝
@Hindsight10124 күн бұрын
I have heard that heat would help
@heidik-lady81352 жыл бұрын
This seems really promising. Thanks
@Hindsight1012 жыл бұрын
Welcome
@billnorris84573 ай бұрын
Well done! Thank you
@Hindsight1012 ай бұрын
Glad it was helpful!
@Hellbob62 жыл бұрын
Thank you very much; this video helped a lot.
@Hindsight1012 жыл бұрын
No problem
@soulv2568Ай бұрын
Best video
@Hindsight101Ай бұрын
Thank you
@FreddyDanny Жыл бұрын
I decided to buy the Ona puller after watching this video. If I were plumber I would buy the Lakeview puller too. Thanks a lot for the video.
@Hindsight101 Жыл бұрын
Welcome
@grousedog88 Жыл бұрын
Shoot it.
@Hindsight101 Жыл бұрын
Lol
@ladawngurley45822 ай бұрын
Oh my goodness!! Thank you for clarifying that when using the Danco puller as you turn and it gets loose, keep tightening down the puller nut because it means it's loosening!!!! Yesssssss!!!!!!!! Thank you!
@Hindsight1012 ай бұрын
You're welcome! It took me making two videos to figure that out
@luisgonzalez-garcia34928 ай бұрын
I have a better one than those shown. They're ok. So it has not broken the brass piece out. Soon will be out. Have a real action videos pulling the cartridges both. No breaks yet and don't have to worry about the tool getting stuck in the valve. Like the first tool you showed. Plastic extractor. But great job in explaining.
@Hindsight1018 ай бұрын
Please share with the channel and I can make a video
@andrewv3007 Жыл бұрын
LOL I already had mine unstuck when I stumbled on this video and it turns out that useless white plastic piece was actually the solution! (don't get me wrong I thought it was useless when I saw it too - pretty flimsy - but it actually worked and only warped slightly)
@Hindsight101 Жыл бұрын
I'm glad it worked out for you but for many of mine since I have hard water that thing would not have lasted
@nevartbabaian5354 Жыл бұрын
you did a great job in explaining how to remove a stuck mow, I have the same problem, but the plumber could not remove it, i wish you were i Glendale, ca area to hire you, I am losing so much water in dreping. thank you
@Hindsight101 Жыл бұрын
I hope you get it fixed good luck
@katieray797411 ай бұрын
I had a plumber tell me that because the old cartridge we have is made of metal, it's been corroded and stuck to the valve body. Does that mean none of these tools will work...? He said my only solution is to open the wall and replace the entire valve.
@Hindsight10111 ай бұрын
Granted I'm not a plumber but I have heard that metal cartridges are a lot worse. You can try solvents and heat or one of the tools I used but there's no guarantee
@keithmulkey3352 Жыл бұрын
This is great UNLESS it had been installed for 15 years like mine...then, you gotta bust it up to get it out