Waveform Generator using Arduino

Check out this complete DIY Arduino Function Generator Project here: circuitdigest....
Components used in this project:
Arduino Nano -quartzcomponen...
16*2 Alphanumeric LCD display - quartzcomponen...
Resistor(5.6K,10K) - quartzcomponen...
Capacitor (0.1uF) - quartzcomponen...
Perf board - quartzcomponen...
Berg strip - quartzcomponen...

[@askinc102]

what is the max switching frequency?

[@69iqtutorial]

U probably want to make a tesla coil?

[@kahe7436]

Both the circuit and code were faulty

[@SpeccyMan]

Someone needs to learn how to use the trigger on their scope.

[@rumahhafidzahbekasi1354]

oof

[@yassinegaming9398]

Sir can you make a frequency receiver exactly like this But receives frequencies wirelessly and gives the value of the existing frequency?

[@jeanyves5380]

There are specific ships including micro-contrôlers to achieve this. They will give you true waves, tricky things and even sometime will include powerfull output buffer for hight level and current output signal.

[@acqurius-gx8lr]

how to keep fix duty cycle of 50%.as when you change frequency duty. cycle is also varying

[@nalinux]

With my Robodyne encoder, I had to add a pull-up resistor for the switch, and swap A and B output. Funny fact, the display goes bellow 0 Hz, aka -6 Hz :) I suppose this can be fixed easily in the code, I didn't check yet. It would be nice to also modify it to have frequency output between 0 and 1 Hz. There's also "const int POT_pin = A2; ", which is not used.

[@TheJavaSync]

Very nice web, hope I can build It soon, thank You :)

[@chbonnici]

Can you give us a link to buy the three pins where you hook the oscilloscope. I cannot find them anywhere. Thank you great video.

[@Circuitdigest]

I not sure to which pin you are referring to

[@chbonnici]

Thank you for answering. The three pins in video at time 0.23secs where you connected the oscilloscope probe. I want to buy some of these pins from AliExpress but cannot find them.

[@Piccodon]

Nice! Can the resolution be increased to say 0.01Hz, or less?

[@owendavidmalicsi5900]

that's like 1 in 100 seconds right? perhaps u can do without a function generator and just use the arduino with delay for that

[@e-teslaacademy1031]

Plz make video on IOT based induction motor speed control using esp6628 ( nodemcu ) sine wave inverter

[@KishanRandika]

Hello , I create this circuit . But it canno't work 🥲

[@electronic7979]

Nice project 👍

[@adnan_oday]

Hi, once i upload the code , this massage ( InitTimersSafe was not declared)

[@innamohammad254]

can it reach at least 1ghz with out any module?

[@gartmorn]

Is this still to be linked as I can't find it on circuitdigest?

[@tonyvarghese75]

Please give the circuit diagram and code

[@thanosxe.8464]

Can it output in AC ?

[@mypkamax]

I can't hear the waveform...

[@Tofupancho]

It sounds like this- woowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoowoo

[@bahrilnugroho1474]

Why you said , "its not "proper sine waves"...i need explanation

[@basicvai3854]

Sinewave follows the sine or cosine formula. But this sinewave is generated by rough enveloping using a crude Low pass filter. Hence this is unlikely to follow the simple harmonic motion.