Making a Portable Air Sandblaster using Gas Bottle | Very Powerful

[@cuba_commander8947]

Muy buen y funcional aporte. Por seguridad me gustaría rellenar el botellón con agua y soldar unas tuercas a las dos entradas que taladrastes. El grosor de la plancha con la que esta hecho el tanque no es tan grande y sólo te permite algunos hilos de rosca. Eso con la presión interior pudiera convertirse en dos proyectiles, pero si le suerdas dos buenas tuercas le da mayor agarre.

[@АндрейСтепанец-г5ю]

Это конечно здорово. Молодец. Пару советов, поубавь давление и отверстие на сопле. Расход очень большой песка. Но, е ли, у тебя свой карьер, то без проблем. Лайк

[@bigred1247]

silica or pure white beach sand is best smaller the better

[@gabrielarambulacontreras9319]

Excelente creacion, pero yo le agregaría un valvula de desfogue de presión, para no reventar las mangueras, saludos desde durango mexico.

[@boblister665]

Years ago I painted a motorcycle tank using a truck tire for an air caddy. I think it took about 4 trips to the gas station to refill the tire. Of course this was when air was free and every station had an air pump powered by a real compressor

[@cinarsinan]

do they take money for air from air compressor at gas station now?

[@blowme5150]

Ya fucking 2 bucks for air everywhere now!!

[@kanu2350]

Lượng cát ra nhiều quá phải có van chỉnh cát cho phù hợp

[@СергейКапустин-щ6п]

1.песка расход большой, 2.кран на сопле быстро выйдет со строя из за песка. 3.эжекторная система в разы проще и дешевле . но Вы легких путей не ищете и за это лайк

[@daledoormaster9072]

When you have the sand running through a gate valve you must have 100% open or closed no half way otherwise the sand will burn out the valve in a short time !

[@julkifly178]

Sxdek Awkpa waktu utuh6fy Kjjhgf

[@StonemanRocks]

Those are ball valves but ya pretty much any valve!

[@richardwomack9196]

Your sand flow needs to be reduced, most blasters accomplish this with a valve or orifice to size. The thickness of the tank metal has very few threads I would suggest a threaded weldon bushing so that you could get full thread contact.

[@zohaibasghar07]

Add an another valve at the bottom of cylinder from where sand is coming out, so it will be controlled sand blasting with high pressure velocity sand, 😊

[@Vinhvlogs-1983]

Chúc buổi tối VUI VẺ nhé cảm ơn bạn đã chia sẻ với

[@ReallyNo.01]

good tunes, great editing.

[@robertantunez9070]

Espectacular la arenadora, muy bueno, felicitaciones...

[@bessi2004]

looks simple and it works..well done.

[@techniciansinc6048]

Think I'll make one of this for my workshop.

[@TAPTV1]

Video hay lắm anh cảm ơn đã chia sẻ

[@gregorycrepin2585]

Bravo , très bonne idée👍

[@bato35]

How many lit/min of air must have nad pressure?

[@galaxialll2743]

Muito bom depois só fazer uma cabine com o funil a baixo da cabine a areia vai enchendo o funil automaticamente sendo reutilizável

[@OnggiYeo]

You have to add 1 more valve on sand exit. So u can control the amount of sand

[@bessi2004]

yeah..he never did ,you rite

[@huuo2496]

Cần áp lực mạnh hơn để đẩy cát bắn vào vật liệu làm sạch.và cát cũng phải nên chọn loại có độ cứng cao và hạt đều nhau thì độ bắn tẩy sẽ đạt được tốt hơn.hơi đẩy nên qua một bình lọc nước để ko làm cát bị ẩm.

[@olivvapor4873]

Breathing sand is highly lethal... ok with a cabin and gloves !

[@HSToutdoor]

Klu stop kran sering bolong gak kak.. Karenakena pasirnya

[@СерёгаХорев-д5э]

Нужен кран, чтобы регулировать количество подачи песка..

[@mccwho]

Great build, What did you use for a nozzle tip????

[@locxamvlog8414]

Lộc chúc anh mạnh khỏe vui vẻ làm nhiều cái hay

[@prafullakumarkhandual144]

Best invention for industrial sand blasting purpose instead of heavy air compressor.

[@bartsimpsonwhothehel]

Could you review the rhynowalk bags please

[@ช่างภาพเอก]

ถังลมกี่ลิตรครับ

[@carlosm33]

Buen trabajo pero debes cambiar la boquilla por donde sale la arena porque la valvula no te va a durar mucho tiempo por el desgaste, puedes hacerla con la ceramica de la bujía

[@tarachandsolanki6685]

कितने दिन यह जुगाड़ चलेगा पाइप लाइन फट जायेगी 🙏🏽🚩💕

[@chrisgalang4381]

What compressor specs do you use?

[@TheDromen69]

The thing nobody says is that a large air compressor is needed to run "acceptable" a sandblaster. If you dont wanna wait a minut and a half to run 10 sec the sandblaster

[@chrisgalang4381]

@@TheDromen69 Ok thanks. The larger capacity the more work you can do while keeping minimum fill time correct? Thanks!

[@masterQ20]

oh God, this is amazing. Your idea is the most perfect thing I have ever seen before. You have 1 more channel subscriber !!

[@bardrick4220]

That's the problem with not using real grit! Play sand is for playing with; it's not very hard or sharp, so it takes a long time to clean the material! I think it's worth the time to make a box too, so it doesn't make a mess, and you can recycle the grit.

[@ronwhitehead3824]

Recycled grit is like going from 60 grit to 240 grit.

[@bessi2004]

glass grit is best so they say

[@sddiymakeitworthit7512]

Nice job 👍

[@wowmrdiy]

great idea but hard to make👍

[@Frank-jn6fu]

You must wear a respirator because of silica dust.

[@hrenes]

Your longues will thank you for making this toy.

[@MdAtik-gf5jx]

দারুণ , ধন্যবাদ।

[@aboaz1200]

Great idea, well done. We are following you from Benghazi, Libya. Greetings to you

[@el5inco129]

Excelente herramienta para el taller 👍👍👍👍

[@_MaYCoM_]

Legal fera mas tá jogando muito areia,assim o deserto do Saara vai até acabar.

[@Songbien86]

Cho mình hỏi để phun được cần bao nhiêu cân hơi ạ . Tsk

[@jamespolucha8790]

Nice job

[@NguyenHoang-gg6vd]

e cũng đam mê quá mà k có đồ để làm k biết ad có nhượng lại sản phẩm này k?

[@ondrejsramek7987]

Wooow Verry good

[@romeovidalrodriguez7754]

hola el video está Genial muy bueno: Salu2! 🤜🤛👍👏👊

[@aurelianogarridocaballero]

Hola muchas Gracias por el vídeo que Tipo de Arena Se debe de Usar por favor?

[@rogertaylor8615]

I would put a smaller tip on it and it would work better

[@unwindingmeditation4577]

Hi guys,can anyone tell me the names of all the brass fittings his using in the video please..thanks in advance

[@voronUA]

Làm tốt thiết bị! Có một lỗ nhỏ hơn ở lối ra vòi phun - ít tiêu thụ cát hơn. Hãy nhìn tôi tương tự.Đăng ký!

[@СерёгаХорев-д5э]

Не в сопло расход, а в кране подачи песка, его здесь нет, по этому и расход большой.

[@voronUA]

@@СерёгаХорев-д5э Có, một van điều khiển cát là phải.🙂

[@СерёгаХорев-д5э]

@@voronUA сразу из баллона должен быть клапан регулируемый. А здесь я увидел только около сопла.

[@АнтонНизовцев-щ2о]

Расход песка божественный

[@umargul5644]

Great 👍

[@jateamentoartisticoepecasa5138]

Ficou top

[@abdell2044]

Bravo 👍

[@dadi_Mixers_repair]

How much bar does this bottle hold?

[@metal8731]

Mantap sukses selalu

[@samduong7302]

can you put water instead of sand so it become water pressure washer?

[@bessi2004]

funny

[@medmusic7977]

Another valve (smaller) and more psi like 90psi and short time to let the pressure regenerate

[@sangreview6217]

Good Job

[@nnamerz]

Quick question: What is the reason for making air enter the tank at the top AND at the bottom using the tee-fittings? Is that so some of the air from the top fitting pushes the sand out the bottom hole....and then some of the air from the bottom fitting pushes the sand out to the nozzle?

[@hamzaismail1658]

So the sand becomes a liquid

[@harotaro1067]

Air at the top will push the sand down towards the bottom outlet. Air at the bottom will mix and give momentum to the sand as it comes out.

[@rottiejakeluke]

Can you please send a parts list for those used to make this? Since you have done this would you do anything different as far as changing any parts or just anything completely different nat all? Thank you.

[@reciclaparaiba5589]

Legal!!! Gosto também de novas ideias

[@Dutcharmytent]

What is it like when you disconnect the gas cylinder from the compressor?

[@tekniklogam5726]

amazing idea

[@jcarney42]

Ball valve soft seats (Teflon) won’t last long with valve partially open.

[@thanhtam6043]

Làm như vậy tốn bao nhiêu phí vậy ông anh mình cũng muốn làm 1 cái

[@Eleutheriosable]

Great, but is the blue hose pressure resistant?

[@pinocolada4254]

Even more important: is the black hose friction resistant?!

[@M-SQUAD174]

@@pinocolada4254еще важнее, устойчиво ли сопло к абразиву )))

[@minhglvlog7607]

Có bán k a

[@DaoVietKnife]

Bên mình có bán mình chế sẵn thế này ko ?

[@ericparedes6948]

Could you tell the pressure of the tank gas in psi ?

[@nathkrupa3463]

Great Sir.

[@HOANGHAITQ388]

Rất sáng tạo nhưng với điều kiện nhà bạn phải ở gần sa mạc Sahara

[@spinny2010]

Works well. But the metal parts at the business end (nozzle) will wear out quickly. Better off with a ceramic nozzle at the end of the hose with no moving parts. Nice build though apart from that.

[@thescappi]

Right. Also the hose will blow in few time… i use only anti abrasion hoses… EUROCORD SABBIA/HD is the best in the market..

[@codprawn]

you can use the ceramic stem from a spark plug as a cheap nozzle

[@homemadetools]

Nice job. We shared this video on our homemade tools forum this week 😎

[@diythichsangtaohp72vlog]

very nice

[@hudsonkilpatrick1766]

Most media blasters no longer use sand, it's considered a nuisance material & considered a health hazard. There is a wide range of other types of media used for whatever the application. Such as soda ash, walnut hulls, pecan hulls, aluminum oxide, titanium, glass beads & plastics.

[@WasLostButNowAmFound]

nah, high humidity tropics mean most of the mediums will be too wet to properly disperse by air pressure. so many other factors involved in different parts of the world.

[@bessi2004]

all material is hazard if you don't use properly. you need PPE special mask and you be fine. doest matter sand or other stuff once you use proper air feed mask

[@boris.teoharov]

Hey, @WEAREXToys what is the diameter of the tap you are using? Is it 1/4th? Thank you!

[@MarioMoran-t3b]

La llave de paso detiene el aire y la arena poreso es que chicote la manguera de la mano si fuera el aire solo no se moviera la manguera pero son dos cosas el aire y la arena😊

[@jaroslavmacura6372]

Na výstupu pro písek musíte přidat ještě ventil aby bylo možno ovládat množství písku...

[@danielvivas2549]

muy buena y faciol de fabricar

[@adrianoandrade3056]

Bom dia, não esqueça de colocar um aterramento saindo de bico do jato até o chão. A eletricidade estática gerada através do atrito da areia vai dar muita descargas em quem estiver usando.

[@Subramanian.p-v4n]

you don not mention the name of the parts used.

[@arturodiazhoyos8373]

Necesita mucha presión. No se entusiasmen. Además la arena acaba en segundos con las llaves de bronce.

[@Ben.aflik163]

Пока метр уголка почистил, машину песка истратил

[@salvadordassi2528]

Good idea but you did not show into us the source of the air that push the sand.it is an incomplete detail if a mini sandblasting equipment.

[@genagans2871]

Зачёт...,👍👍👍👍👍

[@EG-zs7ut]

Need valve in the bottom of the tank to control the amount of sand and get better blast wasting lot of sand

[@Mrnoone26]

Hello what’s the diameter of the holes ?

[@Mrnoone26]

Second and third hole I mean

[@ПавелСедов-п5з]

Под баллоном может должен стоять ещё кран подачи песка??? Много песка в смеси из пистолета, так песка ненапасёшься... Расход большой.... Да и разгона для смеси мал...

[@TrinhLe-zf8wu]

Giá bn vậy shop

[@tuhuynhvan8691]

Ở đâu vậy a?

[@longhuynh4594]

Vũ khí tự vệ khi không còn lựa chọn nào khác

[@valentinbutenko9429]

Не правильно!!! На подаче песка из баллона, нужно поставить кран и плавно регулировать, подачу песка. ПРОВЕРЕННО!!!

[@Николаевич-з1е]

Предлагаю заменить название на "Как не надо делать пескоструйный аппарат". Регулятор давления даром не нужен, нужен влагоотделитель. Большая подача песка, нужен вентиль для регулировки.

[@phuvan3046]

Có bán không anh ơi

[@pfoxhound]

Do you live on a beach?

[@alekseya5350]

Нет регулировки подачи образива. Внизу нужен краник.

[@s.palanipalani9159]

Super

[@salemthai8334]

Helo thahks ban da chia se!

[@octahernandez3019]

Me podrías proporcionar las medidas del las piezas que se utilizan

[@prowled]

first off, is that a _waterhose_ you are using? second, you are waaaaay pnaumatically under pressure when it pulses like that. While this design will work there is a huge issue with safety and weare based on the components. Use correct tubing, use a tank that is made for _high pressure_, and get the right air to sand mix.

[@JBF-GST-Tanda]

Particle inhalation results in LETHAL BODY DAMAGE including fibrosis and cancer. ALWAYS wear proper protection apparatus (respirator / gas mask) while operating sandblasters.

[@minhthai1303]

Cái này đúng là bắn cát nè