What is BLHeli Motor Timing and what it affects?

[@Cake_Doge]

Best video found about this, has visual explanation, has all the info about the difference between high and low timing, goes into science without being boring and with being understandable, has accent, etc. Thanks man!

[@padcom]

Tesla would be proud of you :) that was a very good explanation of how it works :)

[@frankschannel2642]

Good one, Pawel. Excellent explanation..

[@Mekanikern]

Nice, this filled in a couple of holes for me, thanx Pawel 🙂

[@h2o-fpv623]

great videoo it remind me when i was taking classes of electronics and i was so lost but i end it up getting it thank u for this video

[@MCsCreations]

Really interesting, Pawel! Thanks for the video! 😃 Stay safe there with your family! 🖖😊

[@olafschermann1592]

Great explanation

[@djilly75]

Wow i learned a lot. Thank you

[@bryanfpv]

Wow never knew a motor was so sophisticated.Could you show us how to setup blheli precisely. 👍😁

[@fpvpf]

Great explanation. Thx man

[@CorradoCorradini77]

thank you so much! it would have been even better if you completed with DEMAG 😁

[@TX_Nano.]

Thank you. That was very informative and helps me better understand that setting. Is there ever a situation in which variable motor timing would make sense (changing the timing based on either rpm or load) ?

[@terrencejackson4587]

I am trying to understand my issue. I have a 4525 530 kv motor running on 12s. After a 5.5 minute heli flight of a 20lb scale helicopter, the motor is uncomfortably hot. It has a Castle Creations 120 amp ESC. The ESC is only using about 51 amps. The ESC had a low timing of 5. I have changed it to high timing to reflect what the manufacturer setting is.

[@ashGladiator]

Thanks for such amazing explain.. the question here what’s the suitable motor timing should I choose to run everything smoother and more safe

[@jackevans2386]

2:30 is incorrect. You've drawn a 'delta' arrangement, but these motors are wired in 'Star' arrangement.

[@darkodimitrijevic8496]

Live long and prosper :)

[@daphneblake7889]

I have been trying to restore an older art-tech brand heli with a brushless mystery-motor. Labeled B20/10t I want to know the KV rating and poles this motor has. How can I find this out? I cannot locate any info online. The part number is H3D043. Can you find anything?

[@danielalessandrini2299]

Is it possible that an EDF can burn an ESC because of the timing of the motor? I just burned an 150a 12s esc, but I'm not sure what caused the shortcut.

[@JonasCE]

Thanks for a great vids mate! What timing should I set for 5" freestyle (quick rolls & flips) then? Currently I use motor timing set to "auto". Any advice, please?

[@FPVUniversity]

I either set MediumHigh or bump to around 21 in BLHeli_32

[@JonasCE]

@@FPVUniversity will give. it a try. Thank you Sir!

[@chris-ip4pk]

My motor spec says 15 degree timing, however my esc has 12 or 18 ,which should I go for ,and my motor says 8khz drive frequency but my esc has a setting called pwm is that the same,its confusing,

[@tallewinger]

Hi Pawel. I wonder if you can help me solve this extra nerdy problem?? I’m dealing with a brushless 1/10 scale sensored motor. The timing on it is marked outside between 0-60 and is set at the factory to 35. Here is the geeky part. When the ESC is powering it normally (it’s A,B,C fase wires are connected properly) it turns counter clockwise when looking at the shaft from behind. Which is in reverse. So I need to set the ESC to reverse the throttle channel. But I think the timing is off. Because it turns faster in reverse than forward! But since 30 degrees is the average setting (0-60 range) it should not make a big difference… but it does. And when swapping A and C phased in an attempt to trick it into turning correctly it jams! Only vibrating and making a terrible sound. 🤦🏻‍♂️So I would appreciate your thoughts on this. Spasiba my friend. Cheers from Canada.

[@FPVUniversity]

swap any two wires and motor should rotate opposite

[@tallewinger]

@@FPVUniversity Thanks for your reply Pawel. Supposedly. But i tried all permutations and when I swap any wires the motor just vibrates acting as if it is jammed. I think it has to do with it being sensored perhaps. Any ideas? I changed the timing from 30 to 60. assuming that 60 in reverse is equivalent to 0 going forward. I have not had a chance to test it yet to see if this fixes the problem and now the wheels will spin as fast or faster going forward, than reverse.

[@mattraymond2935]

can this setting motor timing or demag burn motors? My motors are cold but every 3rd session I burn a stator.

[@josepfpv2127]

Great explanation. Have a question more or less related. Is it possible to have a configurable mode in a switch in inav when you land the propeller remains or stay in a horizontal position? It would be useful for fixed wings when you land to protect the propeller and the structure of the motor.

[@FPVUniversity]

No, ECSs have no function like that

[@josepfpv2127]

@@FPVUniversity Thanks for the answer . that option would have been useful i guess foldable propeller for the moment . Waiting to see the tests on the ghost system .

[@pteranodon3946]

If the stator has 12 poles and 3 phases that would mean 4 sine waves for each revolution, right? So on such a motor the geometrical angle should be one fourth of the motor timing phase offset. So a motor timing of 24 would mean the coil is powered when the magnet is 6 degrees ahead of the pole.

[@FPVUniversity]

Actually it's electrical RPM * poles (number of magnets) / 2

[@edouardmalot51]

So, does increase timing make the motor smoother ?

[@FPVUniversity]

Not really since torque also grows a little

[@aldenhauser9555]

Can you do a video explaining dmag compensation plz

[@FPVUniversity]

It's in a queue now

[@aldenhauser9555]

@@FPVUniversity awesome!

[@black_baron_net]

☠BLACK BARON☠10:00 Too much 🔥heat🔥 is not good on a long term usage. I prefer more efficiency. Be careful with setting too high motor timings. The RPM can be measured in "without load" and "with load".

[@51im]

I thought that the coil was energised to repel the magnet in able to push it round.

[@FPVUniversity]

Pushing is basically the second phase after pulling

[@magicalpencil]

it pulls it until they are lined up, then it pushes, it is in time with the waveform going up and down

[@FPVUniversity]

yeap, just like that