What is with These OUTBOARD BRACKETS?!?!?!

  Рет қаралды 123,692

Born Again Boating

Born Again Boating

Күн бұрын

Пікірлер: 86
@BornAgainBoating
@BornAgainBoating Жыл бұрын
Learn tons of Tricks & Skills like this with Step-by-Step courses @ BornAgainBoating.com
@Rookie-Season
@Rookie-Season Жыл бұрын
Love a Steiger Craft. Bet that boat had a pretty hard grounding to have fresh gray lower units and a cracked bracket. Those are solid boats. Nice work gentlemen
@guitar1301
@guitar1301 Жыл бұрын
I see the boat hails from Keyport NJ. That's the next town over from me. Are you in Florida working on this?
@pete926
@pete926 Жыл бұрын
Nice job!!! I wanna see another vid when around 55 yrs old. LOL You young guys get into it so well!!
@jamesschulz5518
@jamesschulz5518 Жыл бұрын
Love your videos why did you have to take the bracket off and replace ? Was it broken ?
@destinypirate
@destinypirate Жыл бұрын
Just finished a bracket install. After measuring and marking mounting hole locations Drilled 2'' diameter mounting holes filled with West System epoxy (with the 209 slow harderner), 404, and some extra glass fiber. (3'' transom - built up epoxy with six 1/2 layers - this is 'fastest' I would recommend. - Wash off expoxy 'wax' and rough between layers). Drilled 15/32'' holes through epoxy = the bolts self thread in so tight it seems they could hold without backing. 316 stainless 1/2'' mounting bolts - primed and painted the bolt shanks with marine epoxy, then wrapped in 3M dialectic tape. Cut 2'' washers from HDPE board, full size aluminum backing plate, 1 1/2'' wide 316 washers (over the HDPE washers) - Coated bolt theads and head/nut with Marelube 45. Epoxy primed and painted inside/outside both the aluminum bracket and full sized aluminum backing plate. - All of this to insulate against galvanic corrosion. (Finish with zinc anode) Mounting - Star pattern . On teach nut going at increments of 50lb, 80lb, 110lbs. Two rings outer rings of 4200 both where the bracket and backing plate meet the transom. 2 rings of 4200 around each hole in the bracket and backing plate. Easiest way to dry measure/mount. Dolly with 4 adjustable jack stands bolted on allows for full adjustability both height and angle and easy aligning and moving during prep.
@MikeyDee25
@MikeyDee25 Жыл бұрын
Wow, a Steiger Craft! I ain't seen much about them at all on KZbin. They're made in Long Island, NY - they have a 'lifetime warranty' too. Wish you'd shown some in water videos of it! Great job BTW!
@longlovinfamily
@longlovinfamily 11 ай бұрын
watching you guys work is great 👍 ❤
@BornAgainBoating
@BornAgainBoating 11 ай бұрын
Thank you so much 😀
@ioijiopjkiopjkp
@ioijiopjkiopjkp Жыл бұрын
Have you tried cutting the silicone with fishing braid line? It's what people use to remove car windscreens usually.
@LarryBenson-y3f
@LarryBenson-y3f 4 ай бұрын
Was the old bracket not built strong enough or was there a grounding that broke it?
@BlueWhaler17
@BlueWhaler17 Жыл бұрын
I have the same boat with a pair of 300hp Yamahas….I hope that crack was from a grounding impact and not from wear and tear…My boat has 1200hrs on it pounding out here in the rough Pacific Northwest and there in not one gel coat stress crack on the entire boat. So @BornAgainBoating what caused the crack in the motor bracket?
@ahmadalsabah1704
@ahmadalsabah1704 Жыл бұрын
why did you use the 4200 instead of the 5200?
@elvin12184
@elvin12184 7 ай бұрын
What did you guys do with the old bracket will like to get it if is still available.
@JMonday-k7j
@JMonday-k7j Жыл бұрын
What kind of spray are you using when you go to smooth out the 4200 I guess what I'm asking is what's in the spray bottle thanks been watching your channel for a while
@riccohoward4733
@riccohoward4733 Жыл бұрын
Cool video but I don’t think putting the exact same bracket on was the right move because for whatever reason it failed originally (weight, exceeding the hp rating or just poor manufacturing) it’s more than likely going to happen again. Hopefully it holds up better then the last, keep the videos coming!
@jimr6281
@jimr6281 Жыл бұрын
That was my question as well - why put the exact same bracket on if the first one failed?
@defekticon
@defekticon Жыл бұрын
@@jimr6281 same design, hopefully thicker/better aluminum. Bracket manufacturers will rate the brackets for horsepower. Should be around 450hp. That's what mine is warrantied to. but I only run a 300 on it.
@lawrencemoebius743
@lawrencemoebius743 Жыл бұрын
That bracket is made just for SteigerCraft. Steiger makes the fiberglass swim platform specifically to go on that bracket
@jasonu1123
@jasonu1123 Жыл бұрын
Using an oscillating tool with a commercial window glazing blade will make quick work of cutting through the sealer. Try it!
@georgeanddaddecker7563
@georgeanddaddecker7563 Жыл бұрын
How many billable hours?
@leesevilla2712
@leesevilla2712 Жыл бұрын
I need my boat transom closed in I have a 1995 Robalo 243 to add stern brakitt
@robertovalls
@robertovalls 6 ай бұрын
Great video and a job well done, thank you!
@BornAgainBoating
@BornAgainBoating 6 ай бұрын
You're welcome!
@Julian-ou1ki
@Julian-ou1ki Жыл бұрын
Nexr time keep motors bolted on bracket then loosen all bracket bolts half way off. The weight oc the motors will.break.the 5200 seal. After seal is broken then remove motors and bracket.
@alltree78
@alltree78 Жыл бұрын
All that bracket needed was stronger, thicker, reinforced, or a combo of the three, side plates and you wouldn't ever have any issues again. Love the boat though, nice rig!
@lawrencemoebius743
@lawrencemoebius743 Жыл бұрын
Curious as to what caused those cracks. Hope its collision as some speculated. I am putting a single engine bracket on my SteigerCraft. That bracket and the one I got are custom made for Steiger.
@aaronkelley8909
@aaronkelley8909 Жыл бұрын
I had one crack on a new boat. It was replaced per warranty.
@paulsimpson8990
@paulsimpson8990 Жыл бұрын
You need a transom saver for when it’s being towed.
@buddymitchell5890
@buddymitchell5890 Жыл бұрын
Any advantage of putting a engine bracket on a smaller boat let's say a 18' to 20'
@06barcafan10
@06barcafan10 Жыл бұрын
Me: Watching a video on boat platform replacement. KZbin: You don’t own a boat…..yet….so here’s a little something to watch at 3am.
@bommy673
@bommy673 Жыл бұрын
@10:22 why wasnt he wearing saftey glasses?
@longlovinfamily
@longlovinfamily Жыл бұрын
yup!
@RumblesBettr
@RumblesBettr Жыл бұрын
Would it make sense to put flotation foam inside the bracket? Just wondering since all that weight is so far on the tail when using a bracket
@chrishammer9891
@chrishammer9891 Жыл бұрын
No, for what ever reason you where to get water inside the bracket the foam would suck it up like a sponge then you will have alot bigger issue on your hands
@Mike-hb4pc
@Mike-hb4pc Жыл бұрын
@@chrishammer9891 I wouldn't think it would suck up water if you used closed cell foam. It would if you used open cell foam. Even with all that, I don't know how much it would actually help with flotation.
@talitubi101
@talitubi101 Жыл бұрын
No, research Archimedes' law. Flotation inside a boat helps nothing for a displacement style craft. Well, it does when you boat is leaky or sinking, but you will have different things to worry about then.
@wildwestcoast8095
@wildwestcoast8095 Жыл бұрын
Nice work brand new again
@2fast4you25
@2fast4you25 Жыл бұрын
Did not understand the part where engines get serviced and then get pulled off, layed down and then reeinstalled. Why not service engines ones they are back on after new bracket is on. 😳😳😳😏😏😏
@surfstarcc1
@surfstarcc1 Жыл бұрын
5200 is forever. Love that stuff
@Quackk_Addict
@Quackk_Addict 4 ай бұрын
how much is an off shore bracket like that?
@BornAgainBoating
@BornAgainBoating 2 ай бұрын
Depends, anywhere from $3-5K sometimes you can find used ones for cheaper though
@allanreager3306
@allanreager3306 3 ай бұрын
How come brackets aren’t glassed in?
@BornAgainBoating
@BornAgainBoating 3 ай бұрын
Great question! Not really sure, there are a ton of fiberglass brackets out there that are still bolted on, but then those that are glassed into the boat are almost more considered like a "Euro-Transom" or a "Pod" of some sorts. :/ I guess its all semantics at that point in time. But a lot of brackets are aluminum which can't really be glassed into the transom, they have to be bolted. Now if the bracket is made out of fiberglass, then ok, they could be glassed to the boat, but, the strength of the bolts if fine :) Other than that, not really sure myself lol
@real_emilio_b
@real_emilio_b Жыл бұрын
All these O/B conversions, I understand the cost and ez or repair/replace. But I’d imagine if your boat was design to be I/B there be structural things to consider with the weight shifting. Right?
@michaelreynolds1904
@michaelreynolds1904 Жыл бұрын
That wasn't a conversion. That came from Steiger that way.
@scratchinforstackz2863
@scratchinforstackz2863 Жыл бұрын
It’s a Steigercraft… definitely a New England/east coast style boat
@lawrencemoebius743
@lawrencemoebius743 Жыл бұрын
Long Island built. The bracket too
@Aardvark613
@Aardvark613 Жыл бұрын
Armstrong, they only bracket to consider..
@mypie3301
@mypie3301 Жыл бұрын
heat the inside of the bracket, best way to get 5200 loose
@rogerroger7734
@rogerroger7734 Жыл бұрын
That’s what i always tell people. Heat will take it right off every time.
@apackwestbound5946
@apackwestbound5946 Жыл бұрын
Ya'll make it look easy!
@philipstreechon4523
@philipstreechon4523 Жыл бұрын
Nice work but that bracket is a POS it has only one center web inside that is why it cracked who made that thing and it is a different size.
@noelsanchez3431
@noelsanchez3431 Жыл бұрын
Well done job
@warren6172
@warren6172 Жыл бұрын
Have you seen a lot of listing issues? Or outboard repowered hulls that were made for inboards that feel unsafe when not under power?
@gregeconomeier1476
@gregeconomeier1476 Жыл бұрын
The bracket is cracked and the lower units are a different color than the rest of the engine. I'm going to guess this boat had a traumatic impact that damaged the original lower units and cracked the bracket.
@SeaPro360
@SeaPro360 Жыл бұрын
Not uncommon for new engines to have different color lowers.
@SeaPro360
@SeaPro360 Жыл бұрын
Debond, wedge plus TIME. More debond, more wedge, more time. A little more debond, tap the wedges, wait. Patience and it will come off. You have to keep the working edge wet, so heat is the enemy. Thats not youtube knowledge, thats BTDT knowledge.
@HectorBrooks-r9v
@HectorBrooks-r9v Жыл бұрын
Aluminum bracket aluminum boat??August 1 2023
@whatwouldjasondo2883
@whatwouldjasondo2883 Жыл бұрын
It’s a Swim Step, Swim Platform, etc…
@michaelreynolds1904
@michaelreynolds1904 Жыл бұрын
Blows my mind that Yamaha only paints cowls and not the entire outboard.
@danglin69
@danglin69 Жыл бұрын
6:47 Anybody got a piece of cardboard to go under this thing so it doesn't get scratched? Oh yea, leaning against the building right there..
@CaptDavesSportfishing
@CaptDavesSportfishing Жыл бұрын
another reason I'm not a huge fan. SO MANY HOLES! ''lets build a boat and then put as many holes as we can in it FIRST.''
@davidheitman7004
@davidheitman7004 Жыл бұрын
crap. that bracket will leak. make relief cuts. ?
@markwebb8013
@markwebb8013 Жыл бұрын
Great job guys,that's a lot of work, and you make it look easy. Having done this, I know it is not.
@michaelreynolds1904
@michaelreynolds1904 Жыл бұрын
Editing makes everythink look a bit easier than it actually is.
@fishermanDom
@fishermanDom Жыл бұрын
It’s not is it and the bill will reflect the amount of work and effort involved !
@destinypirate
@destinypirate Жыл бұрын
Pluses - plenty of bolts, 4200 IS better than 5200 here. Fast. Negatives - Too fast. No big backing plates, no anode. No widening & epoxy fill for mounting holes. Too many small bolt mounting points. No assessments (shared) of the transom condition (is it wood or foam/composite core?). No nylon washers or tef-gel/marelube to prevent galvanic corrosion. No Stainless notes (are these 316, anything less is a hazard). Messy outside bead - easy to clean fast with a small plastic puddy knife or astute wet finger. Most important - no note on preventing galvanic corrosion between bolts and aluminum bracket - Bracket needs to be Very sealed against bolt contact. (Some use nylon washers - these have to be rated to the expected compression and I don't know the durability...)
@Phil-km4up
@Phil-km4up Жыл бұрын
You see a lot of boats with foam cored transoms do ya? Definitely 5200 for this application. A bracket is permanent...well it's supposed to be
@destinypirate
@destinypirate Жыл бұрын
@@Phil-km4up Fortunately more and more transoms are foam composites - these give the one chance for a permanant install. Problem is, brackets evolve, break, crack, other issues. 4200 is a great sealant. 5200 will rip through to the paint and fiberglass - yet it won't hold a bracket and motor on - that is the job of the bolts.
@Phil-km4up
@Phil-km4up Жыл бұрын
@@destinypirate what boat manufacturer is using foam as a core material on a transom? Are you thinking of Coosa? An engine bracket isn't an item that is supposed to get replaced, 5200 is absolutely the right choice.
@destinypirate
@destinypirate Жыл бұрын
@@Phil-km4up Coosa is one of the best options these days. Brackets are replaced all the time. One of the most common reasons is damage incurred from the motor striking objects - usually the ramp when sun-baked boaters forget to raise the motor up. Of course the most common reason is due rotten plywood. For the install we just saw, this new bracket can look forward to some nice galvanic corrossion... Few things are permanent on a boat - Ex. Consoles - unless the fuel tank(s) are fully accessible, ''permanent'' consoles need to be removed - hence the wisdom in screws and 4200. Feel free to 5200 a bracket on and see if makes a ''structural hold'' for your motor. - The purpose of the 3m in this case is to act as a sealant, which 4200 does as well or better than 5200, which is something this installer got right.
@Phil-km4up
@Phil-km4up Жыл бұрын
@destinypirate again, what boat manufacturer is using foam cored transoms? One thing I did notice they forgot was to put a sacrificial anode on the bracket. And 5200 absolutely is the right product for this. Your outboard will kick up before it tears the bracket. You'll rip your lower unit off before damaging the bracket.
@arjen580
@arjen580 Жыл бұрын
Fine work people but that sealing job was a mess. Next time use more soapier water and your thumbnail to remove the excess sealant and pull a nice and even seal. And before starting make sure you also wet your hand, each time again before putting your thumbnail back at the sealant. If needed, finish the job with a soft stroke of your wet finger.
@BMWQC
@BMWQC Жыл бұрын
True that!!
@mikeherriges7476
@mikeherriges7476 Жыл бұрын
Also I always use the gun to push the sealant into the joint instead of dragging it over the top.
@MikeLowell-fx8jt
@MikeLowell-fx8jt Жыл бұрын
I’m sure it turned out good and it was just the clip you saw
@TheDoug9901
@TheDoug9901 Жыл бұрын
Welding the cracks would never work they needed to be plated and all this would be unnecessary
@1972mdc
@1972mdc Жыл бұрын
Debond…mystery of 5200 removal now solved
@rogerroger7734
@rogerroger7734 Жыл бұрын
Heat works better
@foxlinks6656
@foxlinks6656 Жыл бұрын
You left out all the swearing and yelling when everything doesn't go back exactly. Not the easiest to drill them holes in place, even getting a wrench in there. Estimate cost?
@mattwoody1089
@mattwoody1089 Жыл бұрын
Your not up on proper terminology so I'll say your amatures
Why I NEVER Flush My Outboard!
15:09
Born Again Boating
Рет қаралды 989 М.
Inboard to Outboard Conversion
18:03
Simon Quach
Рет қаралды 38 М.
ЗНАЛИ? ТОЛЬКО ОАЭ 🤫
00:13
Сам себе сушист
Рет қаралды 3,7 МЛН
Сюрприз для Златы на день рождения
00:10
Victoria Portfolio
Рет қаралды 2,8 МЛН
MY HEIGHT vs MrBEAST CREW 🙈📏
00:22
Celine Dept
Рет қаралды 93 МЛН
INSTALLING OUTBOARD MOTOR BRACKET | EP 7
17:18
ReelReports
Рет қаралды 203 М.
The DOWNSIDE To Buying Used Stuff! :/
25:19
Born Again Boating
Рет қаралды 164 М.
Can I Save This 2-Stroke Outboard? Will It Run?
22:32
Born Again Boating
Рет қаралды 45 М.
Day 2 searay 270 outboard conversion in only 5 days
10:08
SEA MONKEY MARINE
Рет қаралды 37 М.
Boats Brackets Engine Height EQUAL PORPOISING!
8:33
Born Again Boating
Рет қаралды 170 М.
Suzuki Outboard Engine NOT Peeing …
20:11
Will Fix That
Рет қаралды 66 М.
Yamaha OX66 Full Disassembly - Rebuild Outboard
48:11
Catching Colorado
Рет қаралды 110 М.
Got BOAT Prop PROBLEMS? Cavitation Vs. Ventilation!!!
8:08
Born Again Boating
Рет қаралды 592 М.
Putting An Outboard Bracket On A Boat!
12:49
Born Again Boating
Рет қаралды 199 М.
ЗНАЛИ? ТОЛЬКО ОАЭ 🤫
00:13
Сам себе сушист
Рет қаралды 3,7 МЛН