Why Crank Bars Provide in Beam | Bent Up Bars in Beam |

1) Construction cost of 1000 square feet House 2019? Cost of House Construction per square foot 2019
• Construction cost of 1...
2) Grade Of Concrete and water Cement Ratio
• Grade Of Concrete and ...
3) How to calculate Cement, Sand, and Aggregate for M20 concrete
• How to calculate Cemen...
4) Depth of Footing/Foundation and Reinforcement details in Foundation
• Depth of Footing/Found...
5) Maximum distance between two RCC columns?
• Maximum distance betwe...
6) Big Mistakes in RCC Slab - Lapping Mistakes
• Big Mistakes in RCC Sl...
play Lists :
Construction Videos :
• How to Chose Good Qual...
Construction Site Visit :
• New Exterior Design fo...
House Planning Play List :
• How to Study Column wi...
#CivilEngineers #CivilEngineering

[@saleemmazharkhan5761]

Well done in Vlog but still not explained why Cranks bars provided (as per heading question) means which forces are acting, like neutralizing the shear forces, what is shear forces where it is acting & maximum & how etc, with due respect, the lecture is still lacking information, Bending moment with positive & negative diagram should draw separately with explaination, what it's role, maximum tensile forces are in midle so, steel location is down ie. two forth in middle area Anyhow good try, keep it up. Regards.

[@sagarsilwal]

exactly...not explained topics like...how crank bar minimizes negative momemt...how it counteract shear froces acting at support..why most bar provided at mid section just because it has positive BM...many question left unanswered

[@user-jf7ty6tw1k]

Sir gud evening thank you for your teaching ❤

[@welovepakistan8022]

Sir what's a reason negative banding movement top level and positive banding movement lower level sir please explain in next video I am waiting for this question

[@aftabshaikh7860]

Take a paper and apply force on centre of paper the corner uplift and goes to opposite direction of force that' why it's called negative moment

[@mohdtanveer7313]

Mashaallah very good explain sir

[@reyomkato3649]

Good

[@janithalakdinu]

should it be placed in the middle? what does the plan view look like??

[@tyga7704]

Because negative bending moments occur closest to the columns

[@ramswaroop1881]

If the floor thicknesses is 125 mm then .42d = .42x125 = 52.5 mm is right Kindly Advise

[@RJ-29DEVENDRA-BAIRWA-BANDIKUI.]

Good sir important and short notes 🙏

[@saawan10]

Very informative thanks 👍

[@neilbondad9477]

Well explained

[@Engr.Azadul7074]

Very good

[@niinuetey9878]

Yes, I was fine. I am fine, and I will be fine.

[@zazerizhasbro4667]

Assalamualaikum...kindly please explain to get measurement of 042d on bending bar

[@apangaventh]

Sir for g plus 3beam what should be the beam crank bar will it be ok if I use single 12mm bar my beam diameter is 7*14

[@rajamohammed6260]

நல்ல விஷயத்தை நம்தாய்மொழியில் எடுத்துரைத்தால் இன்னும் நன்றாக விளங்குமே.தமிழ்நாட்டில்தான வசிக்கிறீங்க பொழைக்கிறீங்க.பின்னேஏன் இப்படி படிச்ச பந்தாவ காட்றீங்க

[@raghuprasath7631]

இல்லை இவர் பாகிஸ்தானிலிருந்து பேசுகிறார்