Why is my Nitro Engine not Starting?

[@meganfitzgerald651]

Another tip that works well on priming a nitro engine is by pinching the pressure line and open and close the fuel tank lid.

[@TheRCBiker]

nice tip! never tried that one

[@charlesmcgehee3227]

Hi. Never had a nitro engine that would not start until now. When it was new and fresh out of the box the GXR28-SG was a straight forward process to set the beginning settings. Low speed screw .5mm in from being flush with housing. i.e. rather than flush, screwed in .5mm 3 turns open on high speed needle. Idle screw set for a narrow gap. I have tried different gaps. I have plenty of glow plugs and my igniters are all really effective. It started once when it was new. I sent it to Kyosho they said it was fine. But they returned it with an extra brand new carb. I gave up. Put in some after run oil and left it. I have plenty of others. WHY WON"T THIS CAR START? It is not gummed up. Internally it looks new/un-used. I heard about an issue with improperly sized rubber O rings on one of the setting needles. Work this out with me if you think you can. It is a nice 1/8th Vette An Inferno GT2 I must have swapped the glow plugs 5 times. Fuel flows. I warmed up the engine with a heat gun. Nothing I try works.. Yet Kyosho did tell me it ran fine. Not sure why they gave me a new carb.

[@mybackpocket]

You upgraded your mic? No background wind noise. Much better. Great video btw.

[@TheRCBiker]

I've got a new camera with new mic yes :)

[@Jack-jr9ke]

I find it easier to warm the engine up to 60 degrees with a hair dryer when starting it from cold and after 2 or 3 pulls it fires up

[@TheRCBiker]

That's a good tip, but you need electricity to do it! not always possible when you're out :)

[@hazza123live]

JT12's R/C Videos if I'm out an about at my local jumps I've usually driven there so on the way I have my 3.5 trophy in the passenger footwell with the heater on , by the time I've arrived it's warm and starts first pull

[@strider9583]

JT12's R/C Videos love your videos im just getting into nitro just bought a Schumacher swift and its been in a barn for years

[@DavidRodriguez-bl3ib]

I just got one for a Xmas gift and it’s not starting when I pull to start it it’s very Rough

[@ettieneduvenage6723]

Iv been busy with mine for 1 hour i bought it today and its not working and i think i floaded the engin whille blowing so what do i do

[@tazz37kraze]

Hey man ur page is awesome, I do have a question though even though I have done all of that I still can't get my traxxas tmaxx to start again and how often does your motor mounts strip because the motor keeps moving and stripping out my gearing sprocket what do I do man I got it from someone else and I'm so stumped and would love to drive it when it snows where I live

[@jessicaaugust2241]

hi i have a tamiya fs12-s nitro motor, when i bench start it runs and then stops. when the motor are seated in the car then it does nothing. tell me what am i doing wrong? BTW love your vids man they are very informative. lorenzo

[@tonycruz7596]

Hi, I could really use some help. I was giving a HPI Savage and it had a 24.7 XMT nitro motor. I don't know the settings for the HSP LSP and there is a third needle I don't know what it dose.

[@tayubkhan4161]

My acme nb16 wont start I dont have a clutch as the clutch springs snapped will it start without it also I cut the fuel lines shorter

[@HP-HENRYSHORT]

I've just bought a hyper 7 nitro i don't know much about nitro it seen too run okay when started but it takes forever to start like 50 plus pulls thanks

[@TheRCBiker]

Have you tried the things in this video? :)

[@HP-HENRYSHORT]

@@TheRCBiker I've tried some of them just waiting for globe lugs to recharge does the fuel go off when its not been put in the tanks ?

[@N1ghtmare2014]

Is there a video of the HSP Camper Default Carb settings? I wigged mine out.

[@TheRCBiker]

Hi there , I don't know them off by hand. They will be easily found on Google or in your user manual

[@ericgerhart6617]

Ok I have a Revo 3.3 I was running it today it flipped over now won't start

[@dham31277]

When I try to blow fuel through the line to prime the engine its extremely difficult to blow through. New to nitro. Please help!

[@TheRCBiker]

There could be an air lock in the fuel lines. Remove the fuel line that attaches to the carburettor, and then blow through. When fuel starts coming through, stop blowing and replace the fuel line. Then blow again to get fuel into the carb.

[@Martybrown-kc4xg]

my inferno won't start and i've installed a new glow plug and fuel is going in but when i tip my car on it's side raw fuel comes out of exhaust. also, carb gap is more than 1 mm

[@serks2787]

I left my nitro rc in the garage for 2 years and there was a little bit of fuel in it and it's stuck I can't get the jelly and gunk of I need help I've tried hot water but not working do u have any suggestions

[@Martybrown-kc4xg]

serkan karabacak Keep trying otherwise get a new fuel tank

[@ZiKanWatch]

Remove the fuel tank your self and give it a good clean

[@thethreeamigos5207]

I need help I got a 1/16 scale nitro engine and it has a regular glow plug can’t fined a pipe for it don’t know the brand I have been trying to start it using my tmaxx gas tank but with no pipe any information will be much appreciated

[@93jake81]

Jig’s RC Garage it needs an exhaust pipe for the fuel system. Try blowing into the tube that goes to the fuel tank (the one that used to connect to the exhaust pipe) then try starting

[@coolsly64]

hello I was wondering what percentage of nitro fuel do you use for your .18 VX motor???

[@TheRCBiker]

20%

[@daldrete01]

I have a used traxxas t maxx, i've checked everything you said but the tuning part is where everything doesn't work, my throttle idle is set to 1mm, but when i turn it on it works but as soon as i let the igniter go it dies

[@noahv1916]

Daniel Aldrete Ondarza try leaving the ignighter on for a min I know this is late but is it really cold we’re you are at?

[@Martybrown-kc4xg]

replace glow plug

[@grablyb5246]

Mine runs for a few seconds then stops and I’ve never used a nitro rc car before and I don’t know what to do I need heellppp

[@DYLLY0456]

r right

[@runardarriviarsson1092]

Mine just will not start. I spent a straight hour trying to start it but it just would not start

[@leahmorton4977]

anyone know the factory settings for the hsp camper ?

[@brendaoropeza2069]

glow plug is not glowing at all with ez start even after new glow plug

[@Airsoftforall]

Brenda Oropeza check your wiring. You may not have a completed circuit

[@KevinHernandez-yf3mv]

my nitro hpi rs4 3 doesn't want to start and when I pull the pull start it sounds weird

[@TheRCBiker]

I need more details... Could you upload a video of the issue?

[@scbuilds2303]

I love nitro'ss

[@TheRCBiker]

Same :D

[@ethynanderson8694]

Hey so I tried starting my car up and it just keeps pumping fuel through and it won't ignite. I tried setting it to factory settings, it didn't work, I checked my glow plug and igniter, they worked fine. It just won't start.

[@tuthebarbarian9696]

I have the same problem. Did you ever figure it out?

[@ethynanderson8694]

TuTheBarbarian....no it is still an issue.

[@93jake81]

Challenge Master is it easy to pull the pull start? If so, it's lost compression and that might be it. Or you might need to clean the carburetor

[@Will2TheT]

Do u live in Wales ?

[@TheRCBiker]

Nope

[@codywalkden5297]

I hope nitro doesn't die out it's by far better than electric in my opinion I think people just get scared away from it cause it's a little more work than electric but I think it's just a better experience over all

[@TheRCBiker]

I agree, but I think the technology of electric is taking over. There have been no new Nitro models released for years!

[@craigknight1886]

I agree I actually like working on the cars more than driving them

[@benmilner5121]

ThisGuyGaming hi I can’t start engine

[@thetoddperspective]

@@TheRCBiker competition models are still being updated, the eight-x is only a year or two old.

[@hellna6980]

Nitro is over complicated garbage, electrics the way to go...

[@brendaoropeza2069]

I have a T max 3.3 and its not starting with the ez start I took glow plug out and try out next to motor with ez start and didn't glow so bought new glow plug and still doing the same thing it just cranks all help would b usefull thanks

[@Iceberg86300]

Easy start is usually grounded on one of the motor mount screws so make sure you're touching the body of the plug to something on the engine (I just touch it to the head), otherwise you're not completing the circuit & the plug will never glow. Also make sure the connector on the top of the plug is tight. That was the problem with my 4-tec. But then I tried out my old glow stick from my 1/8th scale racing days & found the starts to be much quicker & consistent. But that thing ate D cell batteries so I just went back to the ez start & made sure the battery was always fully charged.

[@bluegrapes3230]

Professional talking Sitting on a pink chair

[@lawrencewinter]

Hey man, nice content on the channel - really helpful and well explained. I've got a losi 8ight T truggy with a dynamite 2.8 engine. The fuel is new. I checked that the glow from the plug is strong. The pull start got a bit stiffer so I thought it must have flooded. Off with the plug, upside down and gave it 10-15 pulls on the pull start to unflood it. when righted, no splashes come out the plug whole, and the cloth I held over the whole was dry as a bone with 10 quick pulls (easy now, only to 6 inches). New filter too. Reprimed it. I've got 1mm gap on the idle. High and Low speed throttle screws back to factory. The only thing I'm worried about is that when the plug is on, there is a knocking sound with the pull - which makes me think perhaps the crankshaft is bent / damaged from flooded pulling. Would this stop it from starting? Might have to strip and rebuild the engine. Can you think of any reason it might not start? I live in Dubai, where its 24 degrees right now.

[@lawrencewinter]

The knocking is only on some pulls though...

[@jakemckenzie5521]

I have a traxxas t maxx with a hobao hyper .21 motor in it and I have just had it running and then after the tank ran out it wouldn’t start again I checked the plug and it had burnt out so I brought a new plug but when I was trying to get it running my neighbour changed the tune and now it won’t fire with the new plug

[@hanquah]

My hsp wont start even i did all the methods, wth is goin on. Im newbies here. I do change the plug but nothing works. Dammitt any help will be appreciated thank for nice vids

[@hellna6980]

Throw it away and go get electric...Nitro is trash

[@fredyperez4307]

Hey I have a redcat shockwave and it refuses to turn on I hit the drill start I can feel it turn but not ignition and both the glow plug and the glow igniter are good fully charged and burns bright but still refuses to turn on eny tips or help plzzz

[@warmachine1479]

I have the same one and experience the same problem

[@RascaoMaravillao]

Great videos ! I have the same engine VX18. Please could you share a basic carb setup for this? HSN (turns) - LSN (turns) - iddle (mm) I would like to have a start basic carb setup in order to adjust later running the car. Thanks. Cheers

[@TheRCBiker]

Hi there, It doesn't work like that I'm afraid as carb settings are different for every engine. It varies depending on your fuel type, glow plug, outdoor temperatures / humidity, etc etc. Need to tune it according to how it's behaving & performing

[@RascaoMaravillao]

@@TheRCBiker I see. Thanks anyway.

[@Hekkie]

One last thing I'd like to add to this great overview, if I may, is the problem of the one way bearing. This is the component on the engine that transfers the force you apply via pulling the pullstart directly onto the starter shaft. I don't know if you've actually ever run into this issue before Josh, but with my car, which is basically the same, I've endured some serious headaches over the last five years with this part. It can be recognized by the fact that when pulling on the pullstart, there's either no distinct sound or very little of the piston turning over inside the crankcase and cylinder head ('slipping'). You'll also find the pullstart too easy to pull and there'll be almost no resistance. If this occurs, it means your one way bearing has worn out. You can't repair them so once broken you'll have to replace it with a new one. The only thing you can do to make them last longer is use special one way bearing oil every half gallon of fuel or so, to keep it lubricated as much as possible.

[@TheRCBiker]

Yes, I did a tutorial on a slipping pull start not long ago :)

[@valium4016]

I am a fan of electric, but recently wanting a nitro. i want to expand my knowledge and have a good ol run with a nitro.

[@charlieweightman3845]

Valium YT nice do it there amazing!

[@tylermccloud3027]

I had trouble starting it then I finally got it started. It ran for a few minutes then quit and now I cant get started again

[@DeerPlot]

Same issue im having. And the pullstart is reallyy hard to pull , and the engine is not flooded any helpp???

[@hellna6980]

Throw it away and go electric.

[@dazspurs9899]

Checked everything in the video too and still the hpiwon't start my other kyosho starts fine

[@bradley6491]

hopefully you can help me i bought a 1/10 rc car a long time ago and forgot what make it is i have no manula either how would i found out how to reset the fule inlet ?

[@Happygrowercbris420]

Hi I have the hsp drift car same motor I need the stock carborator settings please help

[@TheRCBiker]

Check your manual : )

[@mikesmall8871]

My redcat 3.5 21c earthquake won’t start even after I didn’t all of this. What am I doing wrong?

[@TheRCBiker]

Must be low on compression then! Because engines need Fuel, Air, Heat & Compression - so if you've checked the other three it only leaves poor compression as being the cause

[@SiiLENTBUTTER]

I have thf same problem. See if the front engine bearing is bad. I have 3 redcats that all had bad front bearings from factory

[@eldistrofico]

would you know by any chance the factory setting of the 26 cxp engine for the HSP 1/8 nokier / savagery

[@TheRCBiker]

No sorry, but it'll be in your manual

[@DeerPlot]

Im having a compression issue. My vx18 is stupid hard to pull . I know its not flooded , I know its getting fuel, already reset the tuning screw. At tbis point i dont know what to do to it. Ive had traxxas all my life until now and never had an issue starting any of them, now ive been trying to start this pos for 4 days , and on top of that the engine is brand new. So Help possibly?

[@Jayce5800]

Do you have any videos on compression? I have a TRAXXAS 3.3 that simply will not start even after checking everything.

[@AlexanderJuholaJones]

I took my sh .18 powered buggy out today and tried to start it but it didn't run so I returned it to factory settings but it still didn't want to run so I checked my igniter on a spare glow plug and it wasn't glowing very brightly so I charged it and it now glows white instead of orange glow. the point of this post is make sure your igniter is charged and don't be stupid like me :)

[@SuperMoon1972]

Alexander Juhola-Jones hahahaha I've had a similar issue except I was at the track getting ready for my first race ! Talk about feeling stupid , luckily one of the other teams loaned me one ! ( and I left my charger at home 😕)

[@TheRCBiker]

I'd say glow plugs or the igniter is 90% of why these engines don't start!

[@steven12395]

sounds like you made a simple mistake that you are humble enough to admit. you also have learned from that mistake and tries not only to never have it happen to you again but cares enough to help teach others a simple and valuable lesson from your experience. see you have turned something small like a little mistake and are turning it into a thing of good by helping more then just yourself. you turn that into a valuable life lesson, so dont ever call yourself stupid because that you are not.

[@bk502_]

I just received a older Nitro car I have no clue what kind of even is. How can I tell? It doesn't have a body for it that would usually have some kind of name. oh and I also cannot get it to start but I'm going to use tips from this video tomorrow to try to figure it out

[@Sillyscar5]

Hiya pal I’m really struggling with my nitro I’ve watched all your vids but still struggling please help me

[@ThePurplePupUwU]

I hope you get the ruby playbutton

[@TheRCBiker]

A long way to go yet!

[@abdulmutalib2666]

So many video u doit... Give me the more learn that i dont understnd thing... Thanx... Are u still ply rc

[@ekamjotsingh1841]

Hi I have a Traxxas nitro rustler and it wouldn't start or move we buy it used I don't know what to do can u help me

[@tipman98]

Glad to see you doing videos again JT!👍🏼

[@TheRCBiker]

Thanks :D much more to come!

[@realdfprr]

My problem is that there is not going fuel in that cable.

[@TheMisterEGUY]

Hi, my buggy won't start after a head on collision with a sidewalk. My receiver bugged out and lost connection and it kept going. horrifying feeling to say the least. Before I repair the connections I want to make sure it can run again. I've done everything stated in the video. During the crash the exhaust came off the front lip of the chassis bent up and the rc car flipped upside down and was still running for about 10 seconds on its back revving exceptionally high before it stopped on its on. After sitting for 2 days I tried to started and it ran for about 3 seconds and cut out and can not get it to even ignite. Appreciate any help

[@TheInvisibleOrange26]

Alright I’ll do my best to help so your exhaust lip your engines exhaust for any kinds of dents scrapes and damages open it up take it apart simply just check the crank piston and con rod are ok and not damaged from the long period of high speed reving while upside down you will most likely find something damaged check your gears as they may have been Damaged that’s all I can tell you from what you told Me

[@jamalparker8263]

My engine won't fucking start 😤😬😬😬😬😬 drove it ten minutes.

[@pl3045]

I have a 1:10 that haven't been playing for 20 years. I checked everything and they all looked good. However, I can never started the car. The engine quickly dies off after starting. A lot of time it does not start. I tried several high speed and low speed and idle gap needle settings but it does not work (I have lost the instruction long ago). The latest setting is after I blow the fuel into the carburetor the fuel withdraws back into the tank. I have almost fully opened the high speed needle and I am sure that there is enough space for the low speed needle to get the fuel in. I just cannot figure out why the fuel moves back into the tank and why the best I could do was a very short (1s) engine running noise and then it dies off (how much fuel do you have to get into the carburetor?) The glow plug is ok and the engine was cleaned. I don't have the manufacturer's manual so I don't know the default setting. Trying to get this working to spark my 6 year old son's enthusiasm about mechanics and engineering. It would be great if you can help me on this one. The car is a Hong nor I purchased in 2001 (I've checked its website and could not find the manual of such old product, and they do not accept email inquiry). Thank you.

[@TheRCBiker]

It is being starved of fuel, with it being sat for that long I would suggest removing the carb and cleaning it out thoroughly. It sounds like it could be blocked!

[@grahamsmith2022]

Great update to your other earlier video which itself was very good,a reference point I used many times as a rookie!,the fuel one caught me out when I first got my Savage,little did I know how very quickly nitro fuel goes off in hot humid summer weather,also worth mentioning Josh,I'm sure you're aware,but for other folk,this fuel is extremely toxic and is the kind of poison that accumulates in the bodies vital organs and takes a very long time to dissapate,beware when blowing in fuel lines and handling it.👍✌👌

[@TheRCBiker]

yes, I've had a taste of nitro before when blowing on fuel lines LOL it's not good.

[@ronniejess1500]

Same

[@hamzalakhany4561]

Hi bud, just bought a new fox toro , it just won’t start have tried everything , this is my first nitro truck ... I did accidentally fiddle with the factory settings of the throttle and HSA , ISA but have tried to put them back to normal settings .. when I pull the cord some times it’s smooth otherwise there is a cranky noise which comes from the engine ... please help

[@TheRCBiker]

Hi Hamza. Can you send a video of the issue to me on Facebook? Search "TheRCBiker" on Facebook for the page. Thanks

[@dustinplee5067]

My nitro stampede 2wd will not start the guy at the Rc shop tuned it a couple of months ago like 3 or 5 months ago and how do I check the ez start to see if my ez start is bad because it just sits there and reverse it’s a brand new.15 Traxxas engine I moved recently I think for sure my old neighbor stole my brand new glow plug igniter because I ran home and come back to his house and it was going and it and snowed and I would have seen it on top of the snow

[@TheRCBiker]

Huh?

[@Knozo-it1uz]

Everything check! Still won’t start 😔😭 Edit: also straight to the point thank you

[@TheRCBiker]

Thanks for watching

[@thomasfitzpatrick1130]

Heya I have the same engine I put a new one in I can't get it going

[@whynot3413]

My nitro engine starts at first! Then dies and won’t start! It starts at first as it burns the wd40 or the after run oil and then it just won’t start! Tried everything already

[@TheRCBiker]

I highly doubt you've tried everything otherwise you'd have it working ;)

[@alextrim1342]

Mine won't start trophy 3.5 trying to do the first break in procedure started a few times but only got to about half a tank as it cut out most of time then I left it to next day then I tried starting it and it wouldn't start glow plug lights up fine it's at factory settings and it primes however when I do prime it I can here air leaking from the fuel cap

[@vikranttalim]

Hi , I'm new to the Nitro engine cars and have recently bought GS Racing Shadow SB1. The problem that I am facing is that if I don't lean out the LSN then the engine doest start but when I check the LSN setting by pinching method it stops in 2 to 3 seconds max. Which according to the videos on Pinching means my LSN is very lean. I stay in India where the temperature is approx 25 to 30 degree Celsius. The engine is GS Racing .15 . Also when we say 1 turn for HSN/LSN does it mean 180 degree or 360 degree ? Thank you

[@josephallen1164]

Anyone knows the factory settings for my for my bullet my 3.0 it is a pain to get it started.

[@TheRCBiker]

Refer to your user manual :)

[@StefferXXL]

Dear JT12, i have a dbx 1/10. when i got the nitro car, the servo's worked, now as well, but when I try to pull start the motor, it won't start. I think i flooded the engine but i think thats now good. I checked my glowplug and it glows red, so thats not it. And fuel comes in. Pls can you help me??

[@allgood6535]

My head bolts were slightly loose on a new truck would this wrarp the engine reason why not starting?

[@TheRCBiker]

Yes definitely

[@johnbess7320]

Hi I restored a old Kyosho stinger Mk2 and it uses a O.S. Max Cz1 .12 and has a single needle valve and carb gap screw. There’s no info at all online. Any clue what setting it should be at from closed?

[@TheAtkinneil]

Can you do a video for a cold start on a SH 21 engine?

[@TheRCBiker]

Check this out kzbin.info/www/bejne/jIrMgWCtf7CDg7M&lc=z12ctvpy0vvsyx121233v5ornyrrh3rd0

[@filipemoutinho8790]

Hi I have a hpi evo rush and after following all steps and making sure everything is perfect it still won’t start my other nitro cars start and run but this one just won’t any tips would be much appreciated

[@jjjj9416]

I have the same engine but nessed my tuning up at the beginning and don’t remember the settings. I know the altitude we live at are different but could you give me your settings so i could get it to start. This would be greatly appreciated

[@josecalleros9072]

Hello I got a gas RC car engine one kick start

[@noobrefinisher5443]

i bought a brand new hsp 1:10 buggy and used it once then pull start broke so a few months later ive just converted it to drill start because i have bad luck with pull statrs and all it does now is spray all the fuel out the exhasut

[@dazspurs9899]

My carb completely closes when I press brake? (Hpi 4.6) no matter how I turn the idle screw?

[@Kira-bf4oc]

nothing work for me! my car i 2 day it wont start

[@hellna6980]

Throw it away and go electric.

[@josephallen1164]

Well done mate but I still can't get my nitro to start. But your info is good but I still need help if you can. Thanks

[@tobygaming8386]

Hey idk if you still on here but I need help whith starting my nitro engine iv whacked all the tutorials out ther and I cant seem to get it to run

[@dailyriddenhorses7665]

Why are your not uploading

[@zigmasreisas1676]

Hey what if my nitro then i start a motor go full throttle ?

[@TheRCBiker]

The carb must be open. or it's running lean on the LSN

[@hazza123live]

My hpi racing trophy 3.5 doesn't start cold because of my tuning setting/ fuel but a couple of minutes heating the engine up in my cars foot well with the heater on, or using a hair dryer, it starts first pull every time

[@TheRCBiker]

Yes, good idea about putting the car in the footwell :)

[@AK-je4ky]

Mines still not starting I’ve put new gas cleaned the engine and did everything in this vid Please help

[@TheRCBiker]

Hi Ahmed. Keep in mind that engines need just three things to start, they need Fuel, Air & Heat. So, put some fuel directly on top of the piston. Check the Idle gap is open 1mm. And check the glow plug is glowing red. If all of those things check out, it will start!

[@AK-je4ky]

TheRCBiker ok, thanks for the help

[@alexandrossotiropoulos5621]

Compression plays a role also

[@MsSamvlad]

nice chair

[@wearebrandstorm]

Have done all the pre checks and still won’t start. Tried dripping a bit of fuel straight into carb and then it starts and burns off that bit of fuel then dies. Seems like I just can’t get the fuel Flowing into the carb for some reason.

[@TheRCBiker]

Ok that's a good test. Is it a new engine? If fuel isn't getting through it'll either be the tuning needles set too lean (likely the low end), or if it's an old engine the carb could actually be blocked.

[@wearebrandstorm]

Few months old. Have tried richening the LSN by qtr turns upto 2 full turns. And still nothing.

[@TheRCBiker]

What's the HSN Set like? The only other thing I'd check is the seal within the fuel tank lid. Sometimes this can go bad which means the fuel system cannot pressurise hence why fuel is not pushed through to the carb

[@wearebrandstorm]

@@TheRCBiker seal looked ok, but given it a wipe down and opened up the HSN 2 qtr turns turn and eureka, its finally sprung into life again with a bit of perserverance. must have been either of these or combination of both. Cheers

[@oliv3rperez409]

Hey bro did you ever start the Kyosho concept 30 that you said you bought? I also got one I put a new engine and can’t get it starter I’m struggling

[@TheRCBiker]

Hi, no I never got round to using that and ended up selling it. You need a different Nitro for the helicopters, although it should start with the car fuel - just won't run very well. I would try it with the proper Nitro aero fuel before you start any further investigation :)

[@TonyS-qo9qw]

my buggy took a swim, oooppps!!!! ive dismantled and cleaned/reassembled inc most of engine. now ive got a problem. when i try to start engine i find pull start very very stiff ( as if engine flooded ). it is fine when glow plug removed. any ideas ??? bearings mayby ???

[@TheRCBiker]

It's probably the pull starter itself. if the string is wet it wont retract properly

[@CaliforniaPhantom]

Still waiting on a Traxxas rig; your still going to get one right?

[@Layton_RC]

California Phantom He doesn't like Traxxas so probably not.

[@TheRCBiker]

I might one day. personally I'm not a massive fan, and I also want to get a drone soon so that'll come first :D

[@CaliforniaPhantom]

Layton Mitchell he said in a previous video that he would... now he doesn't want to.

[@kryptikpro]

Hey mate I have a HSP WARHEAD brand new I have been trying to start it but it won’t fire over, I have check glow plug it has good bright orange glow to it, also have primed and unprimed my engine many times but still won’t start

[@TheRCBiker]

Are you sure fuel is getting into the engine?

[@plucherongaming7213]

Hello i manage to start my t-maxx after 6 years sitting in the garage yesterday i played with it about 20 minutes and today i tried to start it and nothing. I tried so hard for one hour. Fuel is coming in and its brand new one also glow plug is brand new. Can you help me out please

[@93jake81]

Plucheron Gaming I know this is late but you might need to tune it because the tune needs to change everyday because of weather conditions. Or try charging the glow igniter

[@xuanquanzhi8548]

中文的这方面介绍太少了。英文不知道他说的什么，只能靠看靠猜了。

[@chevylikearock91]

What about an engine that appears to be repeatedly flooding itself? My HpI RS4 3 Evo + keeps flooding itself and won't start.

[@TheRCBiker]

Check the Low Speed needle tuning setting it could be turned out all the way allowing loads of fuel in. But what you describe can be normal in new engines, is the engine new?

[@robertblock2036]

i ran my kyosho inferno neo 2.0 a day and a half ago now wont start i have the D battery glow ignitor maybe thats it...i also have adjusted air filter screw please help...

[@allkyrieirving8191]

Robert Block i have the 3.0

[@jookie2542]

hi can someone help me when I turned my RC car it wouldn't stop moving it should only stop moving when in on brakes the idle isn't to high I reset the tuning things and it didn't work help please

[@TheRCBiker]

Could be your clutch

[@richardweber7984]

I've grown to like your videos for a few reasons. You make them memorable by repeating yourself as much as possible when stressing your point. You're drilling information into our heads at a rapid fire rate subconsciously. As yall would say, brilliant.

[@TheRCBiker]

thanks for the awesome comment Richard :)

[@carlosescobedo8245]

,⁰⁰0

[@jaziejehetkerel]

Nice chair ma

[@TheRCBiker]

Thank you 😊

[@jaziejehetkerel]

😜

[@jaziejehetkerel]

You helped me out a lot man thanks

[@jaziejehetkerel]

Any ather tips ?

[@hannah-meygansalt7525]

My other half and I have recently purchased a nitro car, which means we are newbies to it but we can’t get the damn thing to start up no matter what, we’ve tried so much

[@TheRCBiker]

Hi Hannah, Is it a new car or second hand? You might need to return the tuning needles back to default if it's used. Providing that is OK, remove the glow plug and check it - should be glowing a bright red. With the glow plug removed pour a little nitro fuel directly into the engine through the glow plug hole. Replace glow plug. Check Idle Gap is set 1mm open. If all those things are set then it will start : )

[@719dboy]

Mine wont start up its a showckwave buggy one twnth

[@atonyrodify]

Hello and thanks for the great video I'm new to this Hobby I bought a used Traxxas Tmaxx 3.3 got it running and now I can get it to fire I checked the Glow plug and it wouldn't ignite but then I noticed fuel coming from my Exhaust is this normal?Thanks in advance I subscribe to your channel these cars make me fell young again lol Thanks again

[@TheRCBiker]

Hi Tony, thank you for subscribing. Yes it's normal to see that coming out of the exhaust, it's actually just unburnt oil :) Try putting a bit of fuel directly on top of the piston and see if it fires

[@atonyrodify]

@@TheRCBiker Thanks for the reply back

[@joshuasoto8158]

I have a redcat lightning and I can't start it I primed the engine I bought new glow plugs even a new igniter and nothing please help

[@93jake81]

Joshua Soto i know this is late but try putting the needle settings back to factory settings then try.