Winols beginners guide part 1

[@cristianofernandes905]

this is very help full awsome work and very well explained. i am going to do a course for remaps in london so this videos are very good for us to have some clue.

[@shawng5799]

Hi, I'm falling at the first hurdle and I wonder if you can help me? You open a map you've already loaded before. I haven't, and have to go to new and select mine.Fine with that but then I'm asked what file type it is. I think its a .bin as its a Rover 75 with a Bosch ECU. I'm then asked something about importing with some variables greyed out so can't change anyway. Then I press go and its says no maps found but it displays lots of figures. What am I missing please? EDIT: If this was a video showing you how to make a cup of tea then it would be equivalent to starting with the kettle full already from the last cup of tea that you made.I don't know how to fill the kettle :-)

[@alpye]

Excellent videos i am a complete beginner at re-mapping , show me an engine or a wiring diagram i am fine but the workings of an ecu i am interested in but very lost , i have watched up to the injection quantity maps (4 maps) so far and will be watching the rest tomorrow

[@vagecumap5616]

The person below has been stealing these videos and selling them on ebay. I hope life brings him all he deserves. VAG specialist remaps Dominic Baxendale 32 lower skircoat green Skircoat Green Halifax West Yorkshire HX3 0TG United Kingdom Phone:07922|950363 Email:[e-mail]

[@mohameddhahoua7635]

where can i find the software to download it ?

[@Love01501]

I need help got kkl lead n Ross tech software and Bluetooth diagnostics how easy for beginners to flash a map using nefmoto 1.8t decat n cold air feed

[@amk2vr6]

What do you use to read/flash the ECU? Thanks for the videos, when I get time, I'll watch them all. :)

[@machinesbymarcus1582]

i started using this but i can't seem to find a map to download for my car, 2005 mk4 Jetta TDI BEW Engine, could you help me out?

[@vagecumap5616]

Try searching files on ecuconnections.com They have lots of files

[@matsfroyen]

Thanks for a nice channel :D¨ But i need to ask a question: What is the checksum? and why does that cost money? :O

[@vdubin16vify]

i dont see rpms and engine speed for my maps and how do i fing out if its a maf map or timing map

[@vagecumap5616]

Lots of practice/experience

[@aurick861]

I really have to ask this: Do the maps look the same for petrol engines? what about turbo-petrol engines? Are they the same maps? Could you please make a guide series for petrol cars to.

[@detoxx523]

Thank you for the video. How can i find such files? I am not sure if you mentioned it. Thank you very much :)

[@thuglifescorpion]

Thank you for all the video's! I do have one question: How do I figure out which value's my ecu uses? Experience is one, I don't have any otherwise I wouldn't be watching this :) I'm trying to follow the video's and next to it trying it on my AR 156 1.9 JTD with an EDC15C7. Is it RPM, IQ, voltages or what not. Thanks again!

[@vagecumap5616]

Only a damos for your file with give you certain answer. Otherwise ask on a chip tuning forum.

[@Webrexxx]

I beleve you got thia wrong, The horisontal axis that goes from 0 to 51 is not fuel amount, its probobly the MAF signal. And its probobly not mg/stroke its more likely volts, 0-5.5volts is a typical signal for sensors. The ecu unit doesnt know mg/stroke, its just knows volts.

[@vagecumap5616]

No I am correct. VAG ECU files contain sensor and actuator conversion maps for raw values. The main maps use IQ, etc

[@grcicstevan]

vagecumap is correct, but in fact there are map inside ecu that convert Voltage value to value of air. but that map really not need ever to change

[@77RomanK77]

Hi, I don't find my egr map. I have and w203 c200 CDI

[@vagecumap5616]

not all maps are obvious shape

[@77RomanK77]

vagecumap ok thank you but you said in your videos search the net. Could you explain how I search a picture of a map ? Thank you

[@vagecumap5616]

contact me via website

[@gonzagnr2]

i have downloaded my car ecu file (.bin format) and opened with winols but it wont show potential maps and nothing like you are talking in 10.50 so i cant make double clic like you did in 11.18. can you tell me where is the problem?? Great videos by the way, you are a very inteligent person, thank you for teaching us.

[@vagecumap5616]

What car, ecu ?

[@gonzagnr2]

vagecumap the car is a clio 1.5 dci ddcr delphi Renault Hardware Number: 8200353727 Renault Software Number: 8200334540

[@vagecumap5616]

gonzagnr2 Search Google for similar file to open and compare. In case your download is no good.

[@gonzagnr2]

vagecumap yes i have already downloaded some similar files, and winols does not recognize anything, no potential maps :(

[@gonzagnr2]

vagecumap here you have the file, have a look www.filedropper.com/clioddcrdelphiklineoriginal

[@wilsonazevedo8309]

thks!

[@ads285]

I have a problem. My bmw 2.5tds bin file is in 8bit, and i cant do that high and low. so i cant tell what map is what