With this technique you will do incredible work!

#lathe #tricks #washers #copper gasket #becreative #amazing
Hi guys, after many requests I decided to make this video....
Many people have difficulty turning parts with small pliers, so I hope you enjoy this video!
I want to remind you to always pay maximum attention and use adequate protection!
Even if it's a small gesture for you, every subscribe and like is important to the channel, so if you like the video, subscribe and like the channel...

[@jayminor9757]

Great idea! Simple, inexpensive, quick and works very well.

[@sharkbaitsurfer]

That was beautifully done and such an incredibly useful technique

[@un-factory]

That's good 👍 👍 👍

[@Armanufacturingskills]

Amazing video

[@darioromano5324]

Fantastico.... sempre cose interessanti nel tuo canale

[@user-fm1ff3mj1i]

Bravo Türkiye den selamlar 🎉

[@claudiovandoni7878]

Molto interessante bravo

[@deniscortes9200]

AWESOME!, GOOD IDEA. THANKS.

[@user-fd4qx2yg9r]

Уровень ПТУ 😅😅😅😅😅

[@wawansetiawan4042]

Mantap bos.👍👍👍

[@fabricepoulain02]

Excellente idée. Je suis abonné à la chaîne et j'apprécie beaucoup. Merci 👍👍👍👍👍

[@theoutbackshed]

Great idea, I shall store that up for future use.

[@Massimo68ac]

Magico! 👍👍👍👍👍👍😎😎💚💚🤗🤗

[@NJKTJ]

Thank you so much sir for this new idia

[@Walker7745]

Вот именно для этой цели я сделал маленькую проточку на кончиках кулачков. И теперь любая шайба толщиной свыше миллиметра легко зажимается прямо в кулачки.

[@Armanufacturingskills]

You are doing unique work

[@centurion2185]

Thank you for sharing this great technique.

[@user-qp5iv3sv7p]

تحياتى لك.. افكار ممتازه ومحتوى القناه مفيد ‏‪

[@louisd1968]

😀 tres tres bonne idees merci

[@lotharprimas812]

Sehr sehr gute Idee. Vielen herzlichen Dank. Mfg.Lothar aus Haburg

[@RustyInventions-wz6ir]

Very nice work.

[@garygruber1452]

elegance is in its simplicity.

[@user-vi1ok8vt1h]

Bravo!

[@pawekowalski7469]

👍👍👍

[@jand6329]

Laudetur Iesus Christus 👍👍👍 Deo gratias 👍👍👍

[@retrotehnologii]

Профессионалы так не делают, для этого существуют сырые кулачки с выточками... Но для гаражных хобистов пойдёт!

[@user-cr6ml2xx8m]

У профессионалов два, три,четыре десятка комплектов кулачков (пропорционально стажу работы) под различные операции, гаражные хоббиты могут только мечтать о таком изобилии .

[@williammorris1763]

You know the weirdest thing about watching these videos and knowing what everything feels like in your head.😂

[@localele1]

And if you use the version with a shoulder against the chuck it gives you a repeatable reference for multiples.

[@user-tq3pv6ky9k]

Gracias ahora si me dejaste anonadado lo pondré en práctica 👍

[@lubovmeshkova1458]

Awesome technique. How to made a ring from Teflon with a thickness of 1mm and a diameter of 35mm, dephth - 5mm.

[@annacalise8336]

Making a small grooved adhesive plate works really good too with super glue, but I like this idea even better because you can keep the nice surface appearance without worrying about the heat turning it while removing...

[@peterfromchile634]

Es un antiguo recurso, usado por torneros para fabricar golillas (washers), también se le conoce como "camisa partida" (clamp). Generalmente se fabrica de bronce, material que es más "blando" y rápido para tornear.

[@enricotosco]

🎉💪💪💪👏👏👏

[@clivelee4279]

An elegant solution , however just superglue the washer to the ends of the jaws ( it helps if the jaws are clamping something) , the washer doesn’t as a rule need to be concentric , hold it in place for a few moments with something in the tailstock , good enough for rock and roll .

[@ZlodieIzZaholustia]

Метод рабочий! Но также для этого можно использовать токарный патрон меньше и сделать на нем микро выточки в кулачках

[@user-vt2ng3dh6e]

смять шайбу можно, приходится осторожничать , а в оправе она плотнее сидит, не пережмёшь, особенно медяшки

[@csakanydavid7427]

👍👍👍❤

[@pier3461]

Ciao, sempre ottimi video! è un pò di tempo che ti seguo, hai anche una pagina fb e/o instagram?

[@newtech5042]

Ciao, ti ringrazio... Al momento ho solo il canale youtube, comunque non escludo la possibilità di creare qualche pagina su altre piattaforme!

[@JimBrown-zj2rz]

As a time served machinist I must tell you that you are only half right. what you missed is that you need to mark your fixture at number 1 chuck jaw so that you can put your fixture back in the chuck in the same place that you machined it every time to keep concentricity.

[@newtech5042]

Hi, you're right! However, this is just an example, so I didn't want to waste too much time with the details... In any case, I thank you for the comment which may be useful for users.

[@JSmith19858]

This is what soft jaws are for and do. A lot of these 'simple hacks' are unnessesary with a set of soft jaws used correctly

[@sky173]

That's very good. I wonder how to make a .002in washer/spacer

[@mikebowling3228]

I could tell you how, you need to make several out of shim stock, finish the ID while holding on the OD then do not unclamp and put a bolt through the ID to hold while you remove the OD clamp or bolts then finish the OD

[@mariobenedetti9714]

Guarda che esistono i morsetti teneri, per fare queste cose. Comunque anche il tuo metodo e' valido, anche se molto macchinoso.

[@newtech5042]

Ciao, hai ragione... Ma cerca di immedesimarti nel hobbista che vuole ribassare una singola rondella, pensi davvero che comprerà un set di morsetti teneri per quel lavoro???

[@christophersheward9266]

Would you call this a split collet ?

[@WeebRemover4500]

so simple, i feel stupid

[@JohnBrown-hx5oy]

Would have liked to finish video, but couldn’t because of the irritating music😢

[@douglasfeilen4344]

I guess you mean facing off!

[@user-wm6su2og3n]

Non facevi più subito a fare la rondella?

[@robertsanders1916]

try making them out of steel.

[@sergeypetrov9499]

А что такое-опустить шайбу?

[@user-cr6ml2xx8m]

Возможно уменьшить высоту ( толщину) шайбы?

[@user-hv3mi5sr6c]

это если их 100 штук надо. из за одной не будешь делать

[@ellieprice3396]

How do you "lower" washers? Wrong word.

[@newtech5042]

Hi, sorry for my bad English, what is the right word?

[@user-sh5mv5tu5q]

Древний способ ! Старо как мир !!!

[@user-cr6ml2xx8m]

Уважаемый! Не все такие древние как Вы! Молодые начинающие "наркоманы"металлообработки имеют право знать и древние способы камлания с металлом.😊

[@mikebowling3228]

What a waste of my time..

[@2217Video]

The waggling finger is insulting and annoying, stop doing it.

[@scorpion2nz]

Don’t like it. Don’t watch

[@carlosalbertobarbosa7568]

Se for muitas arruelas de diametros diferente aja matérial.

[@franciscomartindelucia782]

Primero aprende a hablar, girar????