Wunderlich bar riser install BMW R1250GS

  Рет қаралды 23,881

GSD321

GSD321

Күн бұрын

Пікірлер: 76
@markg1291
@markg1291 10 ай бұрын
Just installed the bar risers on my 2022 R1250 GS and the installation was a dream. Thanks for the video. Very helpful
@gsd32i
@gsd32i 10 ай бұрын
Glad it helped
@brianrundle9219
@brianrundle9219 8 ай бұрын
Clear and concise instructions without any annoying music. Spot on!! Many thanks
@DaveBoothroyd-ej5in
@DaveBoothroyd-ej5in Ай бұрын
Great video, but, ironically, not least because it is good to informed about all the hassle with likely clutch cable interference noted below in the comments. I'll give them a miss I think!
@martin9756
@martin9756 2 жыл бұрын
Your videos, presentation and attention to detail are superb. So pleased I found you on KZbin as you gave me the final 'nudge' I needed to decide to buy a GSA. Already specked out, placing the order in the New Year for a March delivery. Intend to do my own 1st Service and then first tour to family in Lisbon in April. Please keep up with the videos and commentary - so good. 👍👍
@gsd32i
@gsd32i 2 жыл бұрын
Thanks Martin , loving the GS . I have just ordered an sc project titanium exhaust and will do a video on that when I get it . I ordered one because I could 😂. Thanks for the comment and taking time to post it 👍
@maciejmaciej1718
@maciejmaciej1718 Жыл бұрын
I've just followed your instructions and I've successfully installed my bar riser. It would be just worth mentioning that if you drop your handlebar too low, it will hit a tank when you take a sharp turn. Cables may also be stretched too much. It happened to me and I had to raise a handlebar a bit. Also, I used only 45 torx bit, You mentioned number 40 was needed as well but all screws are rather 45? Best, M
@davideast7333
@davideast7333 5 ай бұрын
Hi Really good informative and precise fitting video which shows you all you need to know to make the job easy. Please be aware though if you are using a tank bag along with a quad lock you may well have issues when turning the handle bars to full lock eg not enough clearance, and also if you have replaced your oem screen you could be restricted to how much you can move it up and down on full lock
@gsd32i
@gsd32i 5 ай бұрын
Thanks for the input 😁
@brianhill3603
@brianhill3603 2 жыл бұрын
I'm suprised NM sending you bar risers for free to review given they aren't exactly a new product, for what it's worth the Ebay ones at a third of the price do exactly the same job.😎
@gsd32i
@gsd32i 2 жыл бұрын
Brian they just wanted me to fit them as some riders have had issues. Everyone has a choice ref budget.Ride safe 😁
@AndreKooijman
@AndreKooijman 14 күн бұрын
Thanks for the video. Made the install very easy. Did you adjust your mirrors? Looks like I need to adjust them, any tips?
@gsd32i
@gsd32i 12 күн бұрын
Hi, I have been sent carious risers to try and generally end up moving the mirrors but rotating the mirror mounting brackets.
@hrmacdonald4471
@hrmacdonald4471 2 жыл бұрын
Nice install...why did you feel risers were necessary. I like the idea of torquing to company specs. I want to buy a smaller torque wrench and wondering what one you are using. Thanks again for all the great videos & content.
@gsd32i
@gsd32i 2 жыл бұрын
Thanks. Nippy Normans just wanted me to do an install video and this will end up(I suspect) on their site, so they sent me them FOC. I would consider using risers if I were going to do some off road stuff as the standard bars for me, bring me too far over the front of the bike making it uncomfortable . The standard bar set up is great for me as I do road riding mostly. I am Mr Average size but taller riders etc may need risers. I will try the risers on and off the road in the next few weeks and see what I think overall and whether I go back to standard config. 🤪
@TheDervMan
@TheDervMan 2 жыл бұрын
Will you do a follow up vid of how they changed the riding position/comfort?
@garysmythe9545
@garysmythe9545 2 жыл бұрын
Yep would appreciate advice on improvements
@gsd32i
@gsd32i 2 жыл бұрын
I will try and do one this week if I get time, wife has a long list for me!
@anthonyrobinson782
@anthonyrobinson782 7 ай бұрын
Followed your instructions and raised my bars, great instructions but can I ask why you took the old zip tie off just to put another on
@gsd32i
@gsd32i 7 ай бұрын
Not sure TBH 🙈, glad the instructions helped.
@anthonyrobinson782
@anthonyrobinson782 13 күн бұрын
When you fit the bars risers and adjust the bars what you mean when you say parallel to the ground
@gsd32i
@gsd32i 9 күн бұрын
Hi, sorry for the delay. Basically keep the "bar grips" level with the ground, not pointing away from or toward the ground. Happy new Year 😁
@clintlewis1719
@clintlewis1719 Жыл бұрын
I ended up having clutch hose issues. The clutch assembly was too close to switch gear. Move it out to white line on the bar to fix this issue
@gsd32i
@gsd32i Жыл бұрын
Thanks for the input 👍
@phatlakersfan1
@phatlakersfan1 Жыл бұрын
Can you elaborate on that? What kind of issues and what white line? Thanks
@anthonyrobinson782
@anthonyrobinson782 5 ай бұрын
I love how you have your man cave, where did you get them units from
@gsd32i
@gsd32i 5 ай бұрын
www.sealey.co.uk/category/5637151479/superline-pro 👍
@praveennair5588
@praveennair5588 2 жыл бұрын
Hi , Thanks for the video 😊. Just checking Is it necessary to reroute the clutch cables for raising the handle bars. I saw it in few videos. I have done the same way you did for my r1200r.
@gsd32i
@gsd32i 2 жыл бұрын
Hi . I didn’t have to route anything . Not sure if 1250 cables are routed same as 1200r though .
@praveennair5588
@praveennair5588 2 жыл бұрын
@@gsd32i Thanks for your prompt response.
@DimitrisNiktos
@DimitrisNiktos 8 ай бұрын
The brake cable, turning the steering wheel all the way to the left in the lock position is not a problem? There is a solution; Thanks!
@gsd32i
@gsd32i 8 ай бұрын
I didn’t have any real issue with mine . 👍
@terenceokeeffesmotorcyclestuff
@terenceokeeffesmotorcyclestuff 2 жыл бұрын
Cheers 🍻. What was the removal/replacement of the cable tie achieving again? Was there a cable relocation?
@gsd32i
@gsd32i 2 жыл бұрын
To be honest I was following Wunderlichs destructions! ref cable tie so can't give a definitive answer to that one. No cable relocation needed.
@niall5181
@niall5181 Жыл бұрын
Get vlog as usual..can I ask are they standard mirrors on your GS cheers
@gsd32i
@gsd32i Жыл бұрын
719 mirrors
@robertosacilotto3070
@robertosacilotto3070 8 ай бұрын
Is it possible to add this riders to BMW R1250R without disconnecting the cables from the handlebar ( they are very tight expecially that of the clutch ) ?
@gsd32i
@gsd32i 8 ай бұрын
Apologies, but I don't know.
@BikerandBits
@BikerandBits 5 ай бұрын
The easiest way to know if the bars are level is use the reservoir lids…..if they are level the bars are level, as for the clutch side pipes/cables being to short, every GS has the same issue
@tomaszsydney7730
@tomaszsydney7730 Жыл бұрын
Hi, can you specify where I put the longer screws and where the shorter screws? What torque Nm do you tighten the screws with? Regards
@gsd32i
@gsd32i Жыл бұрын
The shorter head screw goes under the handlebars. 19 nm
@Rezaroth
@Rezaroth Жыл бұрын
Thank you for the video. I watched it and bought the risers after that. But when I installed it I saw that when I turn the bars to the far right the clutch line becomes stretched. Could you please tell us if you have the same think on your bike? Mine is a GSA 2021 model. Thanks
@gsd32i
@gsd32i Жыл бұрын
Hi, although the cable was pulled slightly, it wasn't a problem at full lock. I don't know if the GSA has an issue as mine is just the GS🙈
@Rezaroth
@Rezaroth Жыл бұрын
@@gsd32i Thank you for the reply. Mine is a bit concerning. Only the cluch hose though.
@eesqui11
@eesqui11 Жыл бұрын
Hi, I have a question, I have a GSA 2023 and I bought the handle risers but the left side where the cables are stretched, however I didn't even have to do anything on the right side since the cables on that side are very loose. any suggestions? thank you so much
@gsd32i
@gsd32i Жыл бұрын
Hi . Have you tried a combination of rotating the bars and moving the angle of the clutch lever ??
@DUKim-mk8fo
@DUKim-mk8fo 2 жыл бұрын
If the cable tie is relocated, Can handle interference be avoided? Now I'm having interference problem turning the handle all the way. so, I am going to relocate cable tie as a test.
@gsd32i
@gsd32i 2 жыл бұрын
On my 2022 GS I had no issues , is yours the GSA ?
@tomaszsydney7730
@tomaszsydney7730 Жыл бұрын
Cześć możesz podać gdzie wkładam śruby dłuższe a gdzie krótsze śrubyJakim momentem Nm dokręcasz śruby?Pozdrawiam.
@useless274
@useless274 5 ай бұрын
aren't you supposed to reroute the cables outside the fork tubes?
@gsd32i
@gsd32i 5 ай бұрын
Pretty certain i followed the instructions 🙈Not withstanding that , always do full lock check to make sure nothing is going to catch/snag . 👍
@Scrufflebag
@Scrufflebag 10 сағат бұрын
For anyone looking for the answer: you don't have to. But it is a fix for when cables get stretched too tight. I relocated the cables on the clutch side outside of the fork.
@Scrufflebag
@Scrufflebag 10 сағат бұрын
For anyone looking for the answer: you don't have to. But it is a fix for when cables get stretched too tight. I relocated the cables on the clutch side outside of the fork.
@ThePorts77
@ThePorts77 Жыл бұрын
Is there any benefit to comfort with bar risers when rising road? I am considering them as when I stand I feel hunched over (6ft). But interested on how you find them for ‘standard’ road use.
@gsd32i
@gsd32i Жыл бұрын
Great question. I took out a GSA a few days ago and that had bar risers on and was really comfy for me at 5'9". I have had bar risers on that raise and bring the bars closers to you and I didn't find them better than without and the bike felt too different to me BUT the straight forward bar risers were brilliant and I may get some later. I guess if a friend has a bike with them fitted give them a go. Trial and error kind of .
@ThePorts77
@ThePorts77 Жыл бұрын
@@gsd32i out of interest in what way better, just riding position?
@gsd32i
@gsd32i Жыл бұрын
@@ThePorts77 More comfortable in that relaxed riding position.It doesn't take much to change the whole fell, even rolling the bars forward or backward can have a huge change on the bikes feel/connection to the rider.
@jorgenjohansson5440
@jorgenjohansson5440 2 жыл бұрын
I have mounted the risers accordingly and found that the cables on the left hand side are too short. I wrote Wunderlich and they replied that they will look into it but not any time soon. I am surprised that it works on your GS, is it a 2022 GS?
@gsd32i
@gsd32i 2 жыл бұрын
Hi Jorgen, yes I have the 2022 gs and the risers are fine, although on full lock the clutch cable is just starting to take up the slack, but doesn't cause me an issue. Possibly try rotating the whole switch gear/clutch unit around a bit ?
@jorgenjohansson5440
@jorgenjohansson5440 2 жыл бұрын
@@gsd32i Thanks for your reply! I have sent pictures to three dealers now since I can only move the handlebar around 60% to the right then the cables are at their maximum. I have tried now two times just to be sure. Not possible on my bike without cutting/changing all wiring. I have a 2023 GSA which is practically the same as the 2022 and 2021.
@gsd32i
@gsd32i 2 жыл бұрын
@@jorgenjohansson5440 Ok. Best of luck, mine is a GS not GSA. I think the GSA has longer front forks for going off road, that may be why.....but no real issue with mine. Were yours the same bar riser?or a larger one?
@jorgenjohansson5440
@jorgenjohansson5440 2 жыл бұрын
@@gsd32i The very same. Wunderlich, SW-Motech and Motea have the same "up and against you" risers with exactly the same measurements and all of them say "it should work"....but as said earlier, they will check themselves
@gsd32i
@gsd32i 2 жыл бұрын
@@jorgenjohansson5440 OK , Hopefully something simple. Have any friends got the same riser? Try swapping?
@desmiller4764
@desmiller4764 2 жыл бұрын
Bar risers again ?
@gsd32i
@gsd32i 2 жыл бұрын
Des I wasn’t 100% happy with previous video , so I did it again and deleted the first one . 🙈
@neilhutton1528
@neilhutton1528 2 жыл бұрын
I thought you might have fitted a yoke 😏
@gsd32i
@gsd32i 2 жыл бұрын
I would if I could 😂
@Artus6114
@Artus6114 Жыл бұрын
Work not on my Suzuki SV 650,Cables are too short 😒
@pault4513
@pault4513 Жыл бұрын
Wunderlick are $120 Amazon are $20 But the amazon hardware sucks I ordered stock BMW at $2.50 each then trim to final length So $40 total
coco在求救? #小丑 #天使 #shorts
00:29
好人小丑
Рет қаралды 120 МЛН
The truth about handlebar risers
15:09
Bret Tkacs ADV
Рет қаралды 263 М.
Install: Rox Risers 2" Pivoting Bar Risers for R1250GS Adventure
7:13
BMW R1250GS cockpit cover installation  from Wunderlich
19:59
BMW GSA 1250 _ Adding few Accessories
9:07
AshWorld
Рет қаралды 62 М.
Motorcycle Handlebar Risers - Design Development and Ergonomics
7:12
The Six WORST Adventure Motorcycles for Beginners
11:56
Dork in the Road
Рет қаралды 176 М.
BMW R1300GS - Why I WON'T be buying one
5:42
TheMissendenFlyer
Рет қаралды 297 М.
BMW R1250 GSA - Wunderlich Handlebar Risers Installation
21:20
Ghost Rider 69
Рет қаралды 8 М.