X32/M32: Console Configuration Settings (main fader fix, slow faders, hard mutes, link...)

Fix main fader turns down after turning on the console, slow faders after firmware update and Understand all the settings on the configuration page of the m32/x32 live console
- My Instagram: / danielkharrat
____________________
- More M32/X32 Tutorials: • X/M32 Tutorials
- Epic Orchestral Covers: • Epic Orchestral Covers
____________________
-TIMESTAMPS-
00:00 Intro
-- Pop Up Preferences --
01:00 General Pop Ups
01:35 Overwrite Pop Ups
02;13 Load Scene Pop Ups
-- Select Preferences --
02:43 Return to last
03:05 Follow Bank
03:37 Fader Select
-- General Preferences --
04:00 Scene Go Next
04:28 Safe Main Levels
05:37 12h Clock Mode
-- Mute System --
05:58 Hard Mutes
06:29 DCA Groups
06:50 Invert LEDs
07:24 Show View
08:00 Recorder View
-- Link Preferences --
08:37 Delay + HA Link
09:17 EQ Link
09:27 Dynamics Link
09:37 Fader + Mute Link
09:58 M/C master level follows L/R level
10:33 Panning Mode
11:20 Fast Faders
12:01 Bus Configuration
#m32 #x32 #config

[@Bobby_Uterus]

Someone has needed to make this video since these units came out. Again, I wish this channel was around 6 - 7 years ago. You have answered so many questions it’s taken me forever to figure out.

[@digvijaygunjaria1820]

This is so detailed and perfect video thanks Brother❤

[@jacksonabang7077]

You really awesome by giving an in-depth of the m32 console configuration taps nice job bro❤

[@bayphoenix]

You saved me so much time. I haven't gotten the opportunity before to get in depth with the console because of the time crunch and whatever i could explore while mixing a gig. I finally was able to buy one in fall and your videos have helped so much in getting familiarized with all of the goods and nooks of the console. thanks man!

[@ReverbAndBeer]

Thank You again, Daniel! All the scribble strips on the left side of my M32R stopped working (still have color, but letters are blurred), so I tried to reboot, factory reset, etc. I had no idea how to do that and Music Tribe does not offer any useful info in the owner's manual. So I followed your instructions and wal-la - the scribble strips are still blurred, but at least now I can tell Music Tribe support that rebooting, etc, did not fix it.

[@danielkharrat]

Yeah these go bad over time on my console too the scribble strips started doing that. Unfortunately you may need to have them replaced at a repair shop

[@tw2698]

Hello Daniel! I’ve watched ALL of your videos and you are by far a GENIUS!!! I really really appreciate all you do to help many people to succeed in this field. Thank you so much!

[@eliemusic3108]

GREAT JOB BROTHER, THANK YOU!!

[@djabthrash]

Fantastic video, thank you !

[@wijayaproaudio]

You are a hero

[@sound4uaudiovideorecording927]

Thank you, Daniel. This is all great information. Bobby Uterus above is so right about needing this video for a long time.

[@musicalstrategy8261]

thank you man

[@adwareman8349]

Thank you 😁

[@anthony_basta]

Merci beaucoup

[@PhattStaxxTraxx]

Great Videos! I tried to find you on FB as I wanted to know if you'd look over my M32 Scene as its been years in the making and its routing may need some tweaking. I'm using it with Logic Pro X 32 channel recording/playback in DAW, desktop monitors, IEM's, floor monitors and main outs. Routing in M32 Edit is ocnfusing!!

[@danielkharrat]

I'm not on Facebook, you can send me a dm on Instagram or an email to [e-mail] and yes i agree that the routing on the m32 is kinda confusing

[@Bobby_Uterus]

Do you have patron or pay pal or anything? You deserve a couple bucks for this one man.

[@danielkharrat]

No, unfortunately, i do not have any of that

[@gitotunasmusik1461]

Good👍👍👍👍tenk

[@joelromero2949]

These videos are very helpful ! What part of the world do live in? Thank you for the content.

[@danielkharrat]

The Middle East

[@JRandallS]

@@danielkharrat Lebanon? Marionite?

[@NightFeverVar]

Bonjour voilà j'ai fais ce que l'on ma donné music tribe une petite parenthèse j'ai fait un essai avec une table Behringer physique M32 FOH AES50 A > DL32 AES50 A DL32 AES50 B > M32C AES50 A Sur le M32 FOH Allez dans Setup > Global et réglez votre taux d'échantillonnage et réglez la synchronisation sur interne. Sur le M32C (à l'aide de l'application M32-Edit) allez dans Setup > Mixer et réglez le taux d'échantillonnage pour qu'il corresponde à la console FOH, puis Synchronization to AES50 A. Le système devrait maintenant se synchroniser, indiqué par les cases vertes dans le coin supérieur droit de l'écran sur le M32 FOH et sur le côté droit de M32-Edit pour le M32C.

[@IMakeBeats]

Question 🙋🏽‍♂️ how do you make the faders 🎚️ move up and down in different sections of the recording on the SD card??? I need automation on certain 🎚️ faders thru out the song is this possible on the x32 producer without being connected to a computer 💻 Please say yes

[@danielkharrat]

No you can't write automation on your mixer. The only time the faders will "move on their own" is if yku have automation in your daw and the console is following it

[@IMakeBeats]

@@danielkharrat ok so i want to record my session to the SD CARD and then automate certain channels 🎚️ from the computer 💻 is this possible? And whats the simplest setup and software needed to perform this??

[@danielkharrat]

@IMakeBeats if you're recording on the sd card you can't do automation. You need to record it on your computer in protools are ableton or reaper or logic or any daw that you use and you will write the automation in the daw. And if you're using your mixer as a midi controller for the daw then the faders will follow the track automation in your daw

[@IMakeBeats]

@@danielkharrat thx 🙏🏾 so much for responding. That really sucks! Im completely standalone. I dont use a DAW at all. U would think with recall and motorized 🎚️ faders automation would be available within the mixer! Im sad 😢 now

[@IMakeBeats]

@@danielkharrat last question 🙋🏽‍♂️ does the x32 mixer app for the ipad allow for automation?? I purchased the sd card expansion so I wouldn’t have to be connected to a computer 💻 for recording. Is there no other way to get automation in standalone??? 😢😞

[@silverwolf890]

I do have a issue on my x32 where when I save a current mix as a scene and then move the faders for something else then load that scene to use the saved mix to get the fader levels in the place they were supposed to be in for that mix they do not move and remain in the same place as. I’ve been very frustrated with this trying to find out. If you could help that would be so appreciated

[@danielkharrat]

Go to the safes page and see if fader is checked because if it's on the faders will not change value when you load a scene It should be off

[@silverwolf890]

@@danielkharrat I cannot find this safe page you are talking about, I can only find a few safes are on the scenes page and on the home page

[@danielkharrat]

Open the m32 edit app on your pc Go to the scenes button The last tab to the right is called mixer safes Open that tab and look if anything is checked Make sure nothing is checked

[@noiz3116]

Hello! Is it possible to transfer the BUS to the first layer next to the DCA?

[@danielkharrat]

No, unfortunately, the layout of the console is not customizable. It's fixed You can only rearrange the faders on the control app ( m32 edit, mixing station...) but it is not possible on the physical control surface

[@noiz3116]

@@danielkharrat Thank you!

[@LINKERS_SOUND_TRACK_LST]

Hey HI,, i need a small help,, i inserted a GEQ in Bus 1, now there is an option in config tab where i can switch that particular insert as PRE or POST.. what are these for?? And when i use it as PRE, the GEQ works but if i shift it to POST, GEQ DOESNT WORK at all.. can u please guide it to me please!!

[@danielkharrat]

Pre means it comes before the default eq and compression on the channel strip Post it comes after the default eq and compression on the channel strip It works both ways You may be turning off the insert button when switching Just turn the knob don't press on it

[@LINKERS_SOUND_TRACK_LST]

No i checked it,, the insert button is ON in both ways,, this is what confused me actually.. So whats better?? Pre or post?? My dynamic chain goes like, Main signal - EQ - Compressor - Output... So should the insert be PRE or POST?

[@danielkharrat]

@LINKERS SOUND TRACK it depends what you're using it for If it's for monitors do post

[@LINKERS_SOUND_TRACK_LST]

Great help.. thnx a lott buddy.. 🌹❤️🌹🥂🍻