9:05 to 9:07, the single most important moment is missing from the video. It was off, then it was on.
@Jakets3 жыл бұрын
Anyone else w this problem, I gave up trying to install it myself. Took my scooter to a tire shop and they did it in 5 minutes for $10. Save yourself the pain, cuts, bruises, sweat and tears and just have professionals w the right tools do it for cheap. Wish I had gone to them the second I bought the new tires... LOL
@gadgettaco78573 жыл бұрын
Good plan!
@crunkwun3 жыл бұрын
Yip, did that myself. Didn't have the tools to change tyre myself so took it to a vehicle tyre shop. Took 10 mins
@josebarrancas47053 жыл бұрын
Did you buy the same tires?
@gamerdstroyer3 жыл бұрын
Ok. Think i will do that lol
@Jakets3 жыл бұрын
@@josebarrancas4705 I purchased solid tires from amazon. Mine were the 8.5" tires. They are all the same except for the tread design or honeycomb.
@ChristianJull3 жыл бұрын
Many thanks for this video. I'd previously changed the rear to a solid tyre when it got a flat, so I knew it was a real PITA. I'd put off changing the front until it got a flat because I knew it was going to be worse. Following your method it was significantly easier. We had a struggle pulling the motor out until I realised the bolt was stuck. A swift bang down on some wood and it released. The new solid tyre (very much like yours) was fitted on the wheel in ten minutes (I had tyre levers). The rear took me over half an hour (with it heated the same way).
@nalinlee959310 ай бұрын
Nice video. Very clear and easy to follow. I had to boil the tyre twice to make it soft enough to mount. My scooter is a bit different from M365, the motor is not attached to the cover. It took me 40 min to open both covers and found out I couldn't take the motor out anyway lol. Now I have been using solid tyres for a while. It's not as bumpy as I was worried. No problem with speed and battery, everything is fine. I really like them. So, if you are a woman with no muscle, with proper equipment (esp. tyre levers), you can do this alone. Just keep calm, don't get angry. Put everything on the floor, use both feet and whole body weight to put the tyre in, not just 2 hands like in this video. Don't step down until it's done, because once you remove your feet, it will bounce back out and you will have to start it all over again.
@yujiaoliu31423 жыл бұрын
why u cut the most imortant part off
@DonVerchi700as3 жыл бұрын
Here kzbin.info/www/bejne/fHTMZ5mXa7CIqtU
@DBNIGHT2 жыл бұрын
Today I am installing the front hard tyre . The rear one was a pain in the ass . Almost got a heart attack from all the stress and aggravation
@jeeppayton5 ай бұрын
Taking motor apart was just for the fun of it.
@mikem.7422 Жыл бұрын
Bull.... you don't show the hard part. You cut it out men!
@littleworldvines93103 жыл бұрын
I have changed my tube from bicycle repair shop. First of all it took so long time and also it was not easy to fix the new tube inside .we have to cut the nib into half where we fill the air . Then it was adjusted . And now its more difficult to fill in air again , i will suggest if someone wanna buy scooter ,they should have to buy 🛴 with tubeless tires
@miniracincar Жыл бұрын
Ok not so much, because we have gone from the view where you try to mount the solid tire with two screwdrivers directly to the view of the fully mounted tire
@madedigital Жыл бұрын
What the point of showing a video if you dont show the problems and how you solve them Ie you cut and said it takes two people ? how ? show the video SMH
@hekasoram Жыл бұрын
you don't have to take the nub/motor out. You can take the tyre off just as fine with the wheel intact.
@DennisMathias2 жыл бұрын
This was really good. I was surprised that there was a tube in there. I have a Swagtron 5 Elite and I think it is tubeless. But I have a bead leak and am contemplating what to do about that. I worry about getting a new airless tire on there. So I might slime it or bead seal it first. But this video gave me the confidence to at least take it apart. Thanks!
@halko13 ай бұрын
Came to see what has tp be done between 9:06 and 9:08 and learned nothing.
@preston26363 ай бұрын
Lol I feel you. Get some zip ties
@gameofpawns2264 Жыл бұрын
Okay, what you could have done for the hole in the wheel hub is: cut off the air valve on the tube (it's bad anyway and leave about 1.5 - 2 inch of tube for base support), stick the value through the hole and screw the cap back on it to keep the dust out. Looks cool doesn't it?
@mechanickiwi41163 жыл бұрын
Its a lot easier if you lever it up on the rim as apposed to trying to stretch it over from the top.
@gadgettaco78573 жыл бұрын
Thanks for the feedback and I hope to never have to do that job again but good to know!
@DonVerchi700as3 жыл бұрын
I did it in 30 seconds kzbin.info/www/bejne/fHTMZ5mXa7CIqtU
@jardazvuk69463 жыл бұрын
I made it last weekend. But scooter is going about 2-3km slower on maximum, and battery capacity is shorter for about 60%. It has most lower acceleration. I think it is problem of combinations of flat outside profile of tire,and flat inside profile of solid tire. AirTube tire has profile like letter "O",and road-contact area is small. (I pressed it to 6-7atm. 40km/battery.) But solid wheel has flat profile on the road,and has bigger road-contact area and higher rolling resistance. Second thing is permanent small moving in the rim. Tire is soft,and you can hear permanent sound between rim and rubber. Inside profile is not in contact with the rim on all area,only on sides. And your weigth deforms the rubber at first on outside profile to flat on the road, and pressing little bit more inside to the rim. The motor works,and heats up. This all also heats up the tire, then the rubber softens, draws energy from battery. It is like energy spiral. Unbelivable. I'm in Prague(CZ) and is 9degr Celsius. I dont know how it will work in the middle of summer....?! Flat terrain is ok, downhill also, brakes are reliable, but now I cant go to small road climb. Bye all!
@gastonepuzzabbella9214 Жыл бұрын
Battery capacity shorter for 60%... impossible, 20% at most
@jardazvuk6946 Жыл бұрын
Really. Now I have back air tube tires, and I can make 40km again. 12,5km with full-rubber tires.
@lucianpheonix47213 жыл бұрын
I am having some issues,my scooter comes with 10 inch tires and I can't find honeycomb spare tires anywhere. I do have an standard 8,5 inch tire. Would it be possible to use that? I am missing a tool so I haven't gotten to check myself.
@clifflarsen75323 жыл бұрын
You can easily find them on AliExpress
@maciejwojcik33982 ай бұрын
Its much easier with 3 zip tights
@vinceloesink8304Ай бұрын
How do you use the ziptyes
@Adz2713 жыл бұрын
But won’t water go on the hole where you pump the tire
@viking2363 жыл бұрын
No rim is solid and hole is in the rim, water dosent leak in motor.
@DonVerchi700as3 жыл бұрын
The hole is covered by the tire kzbin.info/www/bejne/fHTMZ5mXa7CIqtU
@semyonpinhasov90642 жыл бұрын
my whole fingers are cut not worth it gonna pay the 10$ dollars to get it replaced
@boogiedownnyc Жыл бұрын
I switched to solid tires and I'm never going back
@albertoaguilar62472 жыл бұрын
What´s the brand for the other Electric Scotter ? (not the xiaomi M365) I would appreciate the link to buy it online please.
@nasrimarc7050 Жыл бұрын
Guys i tied 6 times same process not work it's incredibly hard to put the solid tires
@ryd9686 Жыл бұрын
put it in hot water first
@tronghungdao251 Жыл бұрын
Good job
@Foxyboy-iv5cf3 жыл бұрын
Why edit the video at the most crucial part?
@gadgettaco78573 жыл бұрын
Hi, not sure what you are referring to but I will only say this was our first and only time ever doing this and never plan to do it again! Still have the burns ;)
@jarjar503a3 жыл бұрын
@@gadgettaco7857 You took out the part where you actually get the tire onto the wheel!
@Foxyboy-iv5cf3 жыл бұрын
@@gadgettaco7857 Watch the video back, you took out the main part of the video. Showing us getting the tyre on. U used two people. I managed to get mine on by putting the tyre on the ground under some crushed up paper using.my knees to hold the bottom and two tyre leaver's on both sides and after two attempts (first one I put the whole tyre to the other side 😂) I managed to get it. I would say keep the water boiling and when the tyre starts to cool down put it back in the pot for couple mins. Not an easy job by any stretch of the imagination.
@DonVerchi700as3 жыл бұрын
Check this out i have the missing part. kzbin.info/www/bejne/fHTMZ5mXa7CIqtU
@scarydudu58263 жыл бұрын
This video is a bad joke. How many times you edit, try an so on to make this video?! Waste of time.
@gadgettaco78573 жыл бұрын
Ok good feedback and please post the links to your video efforts so we can review them in turn.
@butzgarcia97602 жыл бұрын
the boiling maybe it will take but the microwave i agree with boss
@DBNIGHT2 жыл бұрын
Those pauses are really irritating
@keungcheng69812 жыл бұрын
Don’t do it yourself, I took it to tire shop for $25 installation fee
@justynssagan61563 жыл бұрын
Does rubber tires Damage the bearings in the wheel 🤔
@MoO-jm8ru3 жыл бұрын
Probably no.
@justynssagan61563 жыл бұрын
@@MoO-jm8ru It does after a while because there is no shock absorbent
@MoO-jm8ru3 жыл бұрын
@@justynssagan6156 well I have solid tires of both the wheels now. I had one on the back for a year and after some months the tire got very soft, softer then stock tire at 45 psi and I had no problems with rear bearings. Today I put one at the front. The tire will apsorb shock very well after a few months.
@justynssagan61563 жыл бұрын
@@MoO-jm8ru Well you're not a rough rider That's why
@MoO-jm8ru3 жыл бұрын
@@justynssagan6156 ?
@reggiexp692 жыл бұрын
so what is the review on it? better worse? i got solid tyres on my i-bike mono air eletric moped looks like a xioami clone without bluetooth anyway its hard and has 0 shock absorbers.. looking for a way to make it more pleasant to ride
@MrAwesome10832 жыл бұрын
how can you change a front full rubber tire with a air tire front that has no tube air whole in it
@luisangeltanimontoya32292 жыл бұрын
hi mister, can i buy them in 8p and adapt them to my xprit 10p scooter?
@mikewaynetv24153 жыл бұрын
How long do this tire last and where can I buy some
@Aletzi13 жыл бұрын
Amazon, 2 tires + 2 brake disc 40€ with p&p
@SamuraiBud Жыл бұрын
maintenance free but bumby rides
@southiesboxbreakphretrogaming4 ай бұрын
No if you install suspensions
@warrenbrowne15692 жыл бұрын
I did the front tyre on my sons and did it piece of piss in about 5 minutes with the motor and wire still attached.
@shekey8312 жыл бұрын
Can I bring mine round to you please
@sillverstreak6 ай бұрын
And me ? @@shekey831
@miniracincar Жыл бұрын
Ok non tanto , perche si è passati dalla visuale dove si cerca di montare la gomma piena con due cacciaviti direttamente alla visuale della gomma completamente montata
@Aedhum2 жыл бұрын
Can I use it on the rear tire?
@wakilnadaph97 Жыл бұрын
How much front tyrie solid from qatar
@fighter672 жыл бұрын
cool
@mastaofthemetavrse9762 жыл бұрын
My grand pa said 1 in the stinky n 2 in the pinky ? Fk no’s
@11122233331112 жыл бұрын
sorry to hear u got melested
@andrewwoy87822 жыл бұрын
Okay, how do you remove them when they wear out?
@SirPhillyLeong2 жыл бұрын
With a knife.
@11122233331112 жыл бұрын
cut them off
@Nick2102 жыл бұрын
Your battery will shit the bed before that happens. If you’ve had your scooter long enough to wear out solid tires, it’s time for a new scooter.
@Mr97gilad2 жыл бұрын
@@Nick210 my started to dead after 3 months. Not gokd china quality.
@leemurray36533 жыл бұрын
it was the most frustrating thing I have ever done! never again
@gadgettaco78573 жыл бұрын
Hi Lee, yes I agree and actually we would be happy to never do that again as well!
@axiomloves213 жыл бұрын
The tires are tighter than that hooker on the red light districts bumhole in Thailand
@DonVerchi700as3 жыл бұрын
Took me 30 seconds to do. Not hard at all. kzbin.info/www/bejne/fHTMZ5mXa7CIqtU
@lacky912 Жыл бұрын
dont
@philbess7051 Жыл бұрын
thats a horible how to video
@Stewsound2 жыл бұрын
lol this is not the way to install a solid tyre.
@11122233331112 жыл бұрын
it worked for your mom
@mArs0ll2 жыл бұрын
My tire is size 8 1/2 x2 but i bought a solid tire the of 8.5 x2. is it possible that i can use that 8.5 tire to replace the original one?
@barakcobrama17032 жыл бұрын
i bought a monrim 500w tyre and that has a 10ince Tyre on it and it fits just about its great cos of soft solid 10ince wheel makes for a way better ride.
@barakcobrama17032 жыл бұрын
just want to add i put the solid wheel on the back instead of my silicone filled tyre and its really bumpy feels like cheap xaimi m365 i want my ilione .
@zwirek34883 жыл бұрын
I bought in UK. Don't buy this rubish scooter. We had two regular and pro versions. After 2,500 km, the engine will be so loud that it is impossible to drive. Bearings practically impossible to replace. Will start to violin, tap. The brake cable will break. It will stop charging. Replacing a punctured inner tube is a nightmare . My friends scooter broke down after 1200 km. The Xiomi warranty covers nothing under warranty. They demanded 3/4 of the value of the scooter for the repair of a faulty loud motor of no known fault. Stay away from these chinese scooter…
@jamo88962 жыл бұрын
Motors are 30 quidd...
@CJTooSturdy23 Жыл бұрын
U tryna get us to but the TikTok scooter for £100?