My F15D Yanmar 3-point lift stopped working. I really appreciate your information. I'm much more likely to tackle the job of fixing it. However I need to use my tractor while the weather is cooperating so I rigged up a 12v Harbor Freight 1500 # winch to the rollover bar and for now it works good enough to get the work done. Well done!
@kssandhu46934 ай бұрын
Nicely followed up on problem..Glad you fixed it the right way..Great education Sir…cheers.
@gudidpadasian7729 Жыл бұрын
that beautiful work step by step system very good that give me idea to repair my yanmar 2000 ha...ha...thanks a lot I appreciate you movie.
@qzorn44405 ай бұрын
Excellent Yanmar Hydraulic repair and information video. 🥳 Thank you.
@bennyhill3642 Жыл бұрын
Great Video Awesome detective work😇😁😇
@emilio313139 ай бұрын
Hola amigo te felicito por el vídeo, que está bastante bien; Tengo un Yanamar 1300d y no me sube ni me baja el rotovator, empiezo mirando el filtro?? o que me aconseja??, muchas gracias Un saludo
@ChristianCorrectionsCorporal2 жыл бұрын
I just bought a YM1500 and its leaking hydraulic fluid out the top of the 3 point actuation valve where the copper washers and bolt go into the top. Going to order a couple of those copper washers and hope that does the trick. Any tricks to getting that supply line in the right place to get the top bolt to go through it and back into the top of the valve?
@goodolboys7132 жыл бұрын
I have never had any trouble with them, it’s just like a brake line on a car, it should seal up without too much trouble.
@beartrace1 Жыл бұрын
I HAVE A YM1610D. 3 pt does not work. FEL works fine. Hydraulic screen clean. Hydraulic fluid clean.Removed the 3 pt actuator.. Did NOT see any steel ball. (a) Should I have one? Does not show on parts manual. (b) There is some minor abrasions on the piston - it this a concern? (c) Examined the valve from above through the 3 holes, looks clean. Your suggestion on what is next?
@garyserjeant7270 Жыл бұрын
What fluid do you use in this tractor ?
@goodolboys713 Жыл бұрын
Jd303 or j20a
@chrispapsidero6318 Жыл бұрын
I have a yanmar 1500 and the 3 point picks up a heavy load but slowly comes down. Hydro pump makes and little bit of a whining noise any suggestions?
@goodolboys713 Жыл бұрын
There’s a little lever that flips around, best way to describe it is it’s a roll pin that is the lever. Flip it around until the implement goes down faster. I believe I showed it in the video. If you need more help let me know. I would have to look at mine to remember exactly where it’s at (somewhere on the upper of the rear transmission box.
@kabirieranaan17052 жыл бұрын
I have tractor having problem to bearing and I don't know how to repair or replace the bearing
@goodolboys7132 жыл бұрын
That’s going to be fun. More than likely A lot of stuff will have to be split apart for that fix.
@outinthesticks10352 жыл бұрын
Tractors I have owned have a screen like that on the hyd. pickup , but a pleated paper cartridge after . After 40 years it might not make much difference but I wonder if there is any benefit to adding a bypass spin-on to get finer filtration . I have never worked on yanmar , so I might be talking out my a**
@goodolboys7132 жыл бұрын
I’m sure there would be a benefit to adding a spin on filter that is for finer particulate. The trick would be finding one that’s high flow enough. None the less, the tractor has ran for years and years and years without so I’m guessing there probably is not a real need for a fine filter. Thanks for watching!