You Only NEED 2 POWER TOOLS!! (Here's What They Are...2 MOST IMPORTANT Power Tools)

[@TheHonestCarpenter]

Are you sure you’re using your power tools safely? Avoid the most common (and dangerous) mistakes! Get your FREE guide here 👉 bit.ly/10PowerToolMistakes

[@highwatercircutrider]

I have been a building contractor for 49 years. I started in 1972 with an old $2.00 Craftsman circular saw, my dad’s old 1/4” electric drill, a roofing knife, new tape measure and a straight claw hammer dad gave me needing a new wood handle. My first two years were spent redoing shingled roofs. By 1989 I had built up a small house moving/ steel sea wall business. I retired 3 years ago and sold all my heavy equipment and a shop fire burned up my office and tools. Two years ago I got bored and talked my three brothers into going back in the carpentry business. I had to buy a saw, cordless drill, impact driver and a new leather tool belt......... I am happy once again at age 70 ! ..... Gary in Michigan

[@jixuscrixus1967]

I spent a lifetime in oil & gas construction supervision/management, retired early and started some woodwork DIY projects, replacing standard size doors, workshop doors, garage doors, building workbenches, window frames, shelving. I started some of the early projects with discarded pallets, then found a local timber merchant and purchased timber for the more important jobs. Fantastic way to stay active and occupied, great job satisfaction and fun collecting some good tools along the way, I’ll tackle most DIY projects if I feel comfortable with the level of detail required and my abilities.

[@lahcenmartinez7574]

I've been a chef all my working life. Not easy, but not carpentry. This past year all I could think about was changing professions. When I was 18, I had rented a house that needed the large living room "picture-window" replaced. The man that was hired was named Johannes. An old German with nothing but time on his hands to make more money. His stories and rants during the week were the stuff of legends. Enjoyed making him coffee, just black, and sharing breakfast. I have no doubt that he could've finished the job in 2 days, but he just took his time and enjoyed my company that week. Still thinking about changing professions, but my knees hurt.

[@staffh3815]

Fair play Gary, long may u continue

[@elzoog]

@@lahcenmartinez7574 Is chef a good profession to get into? My daughter is interested in doing that.

[@lahcenmartinez7574]

@@elzoog If you like what you do, and you're good at it, then get so good that people have to pay you what you're worth. ALWAYS NEGOTIATE. That's just basic advice for any profession, but honestly, you have to really love it and find a good fit for YOU when looking for long-term employment. I would have a resume 4 pages long if I listed every joint I've worked in. Bosses can be overbearing and customers can be the worst of humanity, but you push through it, develop a thick skin and own your work at the end of the day. You can't please everybody, but you will try, and you will learn from failures. Being the Chef in the kitchen carries a lot of responsibilities and garners all of the respect when you live up to the name. I've loved my job when I'm there, and hated it sometimes when I'm at home with my little girl. Sacrifices will be made, just like with so many other professions. Hope that gives you some insight.

[@fredberger3155]

I agree. Being a retired journeyman carpenter, I was often limited by whatever tools I could carry in my car. When I started the trade, I did EVERYTHING with a circular saw, a drill and my hand tools. As time went on, and Chinese power tools became readily available at cheap prices, I bought more specialty power tools; pretty soon I needed a van to move everything around. One day I said enough is enough, I went and bought two tool bags from Home Depot and decided if my stuff doesn't fit in those two bags, then I'm not using it. One bag holds the circular saw and cordless (with hammer function) drill. I had to consider each hand tool carefully for the other bag, but I did it and I feel a real sense of freedom because of it. I have a knockdown portable bench that I built; it also allows me to position my circular saw for use as a table saw. So when my kids call me for help, I'm ready . . . two bags and a portable bench . . . and I'm gone!

[@helenm6732]

“Help”, said the adooted kid.

[@wesleymunoz6474]

Maybe you should make a “must have” tool list for the younger generation. (Me lol) I started my tool collection and I noticed that sometimes I just buy things just to have. Mainly for house maintenance nothing professional

[@dilipanthonypinto1620]

I’d love to see a picture of your table setup because I’m in the same boat. When I need to rip trim casing or door jambs , I hate to drag around a table saw…

[@oaktutor1154]

this sounds so cool, i could see it in a movie. We shall call it "Dad, a carpenter near you"

[@cw9790]

I'm a minimalist and also a craftsman so this information is exactly what I needed.

[@barneygo2010]

30 year Master Educator here (High School Teacher) who spent 2 semesters in electrical trade school and worked in construction afterwards; Thanks for not wasting a word nor wasting our time. I learned so much , but learned even more from your videos. I was mentored by a Master Carpenter and you both are on the identical wavelengths. Much gratitude to you, Kind Sir! Peace Be To Journey!

[@streetglidescott6424]

Thank you for your service! Shop teachers are under-recognized contributors to life as we know it.

[@MAGAMAN]

"Master Educator" So you couldn't hack it in the real world. As the saying goes: Those who can, do; those who can't, teach.

[@kenrichmond6906]

@@MAGAMAN what kind of stupid comment is this? Completely unnecessary.

[@tharealje2306]

@@MAGAMAN weirdo

[@dieabsolutegluckskuche5174]

​@@MAGAMAN That's the reason why america and most western counties have such a bad educational system, because so many of you don't give a fuck about education in many ways. Finland only gives teaching positions to the best from the best and no wonder they got the best schools, teachers and pupils. Bad schools means bad management, bad teacher means bad pupils. And bad teachers are a byproduct of your society.

[@5400bowen]

“You may have trouble convincing me, but I’m always open to suggestion”. That is the right attitude for a person of your insight, depth, and clarity. At least half of your comments are things I have thought and dealt with, and learned over the years. What’s really funny is that you look like my family in a general sort of way. Keep up the good work.

[@codywaldron2486]

As a now 3 year home owner, I couldn’t agree more. I found a SkilSaw brand circular saw at the local pawn shop for 10 bucks and bought a brand new Craftsman drill/impact set right after I bought my house and finding out I had a place to store tools. I’ve constructed so much stuff; expanding my deck, building a base for a shed, adding a workbench, shelving, and a ramp for the building, a dog house and tons of other little projects. You hit the nail on the head with this one. It’s mind blowing how much you can build with a way to cut, and a way to fasten.

[@kimtoy3089]

I like how you describe carpentry as cutting and fastening - puts your tool choices in proper perspective. Thank you!

[@donnguyen9493]

When I was a refugee on a Malaysia island, I only used ropes and a medium long knife to build my "house". It survived couple bad tropical storms and a lot of heavy rains.

[@mikhail58]

Omg were u ad bidong

[@donnguyen9493]

@@mikhail58 Actually I was at Pulau Besa. Bidong was built roughly 6 months after the Malaysian government decided Besa was too small to shelter 1000 refugees. It turned out to be a good plan as Bidong at its highest point had ~50,000 refugees.

[@aquarius9491]

in America thats called a rape kit.

[@firstnamelastname59]

@@aquarius9491 ahhhhhahahaha

[@christophresmerowski1824]

Wilson !!

[@survivalsoundsVEVO]

For #3 I’m new to working with tools but love my Dewalt Cordless Multi Tool. I can cut through almost anything, plunge cut, fix mistakes, sand rapidly with a few affordable attachments… so much versatility.

[@TheRozylass]

Amazing! I've been telling my husband for years that all my Dad ever had was a circular saw and a mitre box for all his cutting needs. And my great-grandpa earned his living as a carpenter with all hand tools! Keep up the good work!

[@HariSeldon913]

And your parents grew up with a 14" B/W CRT television and your grandparents grew up without television at all. 🐱🐱🐱

[@calebfuller4713]

@@HariSeldon913 They had to walk to school, barefoot, in the snow, and back then it was uphill both ways! And that was considered luxury...

[@Skinny_Pimp]

Why are you nagging your husband. Can the man have some peace. Simple. Do you want him trying to solve all your issues or just listen?

[@Shauma_llama]

@@HariSeldon913 My parents had a COLOR tv, what're talkin' 'bout?

[@Shauma_llama]

@@calebfuller4713 My mom rode her horse to school when she was kid. Really.

[@khalidosman8027]

Applicable for DIY around American homes which are often wooden. Here in South Africa the most used tools are a hammer drill and angle grinder since the homes are built with masonry. Hammer drill can be used on low setting for wood and there are special blades to use on a grinder for wood cutting.

[@sluggo5260]

This video sums up my life when it comes to "required tools", and tools "I wish I had...about once or twice a year". Your honesty is refreshing. Thanks.

[@LaurieSavage]

Carpentry is about THREE things! MEASURING, Cutting, and Fastening. Love your videos, they are very helpful.

[@billyandrew]

@@01r1sh Damn, you got in a week ahead of me! 😂 I was taught that over half a century ago and it's as relevant today as it was back in the day.

[@jcollins7593]

Which power tool should we be measuring with?

[@aTribeCalledCasey]

@@jcollins7593 what is measure?

[@emostorm7]

I thought this too right off, but he was talking about power tools

[@BobZed]

Other people caught this, but I was thinking, "I really want to see a power measuring tape."

[@stroys7061]

My grandfather could do great work with a hand saw, hammer, brace and bit, and a few other small tools like screw drivers and chisels. I admired his skill and bought power tools as soon as I could afford them. Now I’m about half as good as he was.

[@rodneyadderton1077]

Yeah grandfather's are the best.

[@tylerstraka8714]

Step by step you get ahead, but rarely in fast spurts.

[@nagp7650]

It's not tools , it's technique,application of brain/mind.,patience& Finally if u Love ,u r work irrespective of outcome Japanese do wonderful artcrafts with bare minimum tools& also ancient Indian Temple architecture

[@blamonte4931]

yeah I still remember the smell of my grandfather's garage, dirt floor, and oil. all kinds of repair and creativity.

[@noahleek9696]

Yes. My grandfather past a lot of tools down to my father which he has passed to me. I have 4 different sized handmade wooden levels. I love them.

[@cuses-ws5gp]

I never had many tools (power or otherwise) until we bought our first house. Shorty thereafter, I saw the need for a power saw (the cutting of shelving) and a fastener (drill pilot holes for screws et. al. to assemble the shelves). Those lasted me for quite some time. As I became older (and batteries became better) I switched to cordless tools and increased the number of tools to 3 - circular saw, drill, and impact driver. I have a couple of other power tools, but they basically have stayed in the chest where I first put them. Now (at almost age 80) my power tools used in order are: impact driver (fastener), drill (fastener II), and occasionally the cordless saw. I was tempted to get a sander several years ago, but I have a multitool that has a sander attachement. It does all the sanding I need! One last comment - buy the best tools you can as you go along. You will not regret it. I have friends who have drawers full of old broken down, cheaply made tools. They are NOT worth it!

[@AndyMorrissey]

#cu63 ses53 I can testify to your "One last comment" I too have tools I wish I had spent more on. Not only do better tools last longer they make doing the job a lot easier and quicker. Even if your only like me doing odd jobs around the house getting an 18V cordless drill and separate 18V cordless driver has made my life so much easier.

[@gmanchurch]

Amen to that brother! Buy the best tools that you can afford!

[@chatteyj]

Pretty much why I have gone for the makita range of cordless tools. People say they are good I have no idea if that is true or why but thats what I went for, hopefully they turns out to be good.

[@vanessa7349]

Mate, so glad I found your channel. I'm an absolute beginner and could not find any hobby courses to learn the basics. All your videos I've watched so far have been so helpful. Just want to say thanks. Felt especially reassured with this 2 power tools video.

[@TheHonestCarpenter]

That’s awesome, Vanessa! Thanks for watching! 😄

[@covakoma1064]

@@TheHonestCarpenter can you please tell me circular saw, cord or cordless? Also if you go 18V ( have other makita tools cordless) whitch one to look at, makita have really a lot of tools to pick up?

[@chatteyj]

@@covakoma1064 makita cordless tools is a good way to go, thats what I have chosen, but I don't like circular saws myself

[@cactustactics]

@@covakoma1064 there are links in the video description, but if you pause the video you can see the model he has/recommends

[@ChipVorhies]

When I seen the name of the title of this video, I already knew my top two picks, so I was not one single bit surprised to see that you chose the same ones. I am completely in your corner on this one!!!!!

[@tylerstraka8714]

I guessed right too. I am not sure 18 volts on the cordless drill if that is too powerful or not powerful enough it just seems pretty average

[@ubbno1]

@@tylerstraka8714 Believe me, 18 is fine. I had a hammer drill I could use on stone or concrete yet had no problem, different bit of course, on pine. 18 is the sweet spot, especially with the new lighter batteries.

[@Markdmarque]

Absolutely spot on. The tools I use most!!..Makita cordless circular saw and drill both 18v lxt powered

[@nizamdamanhuri933]

"Carpentry is about two things - cutting and fastening" - putting that on a big notice above my work bench for those times I get into an over thinking spiral.

[@chrishane1316]

And finishing, lot of finishing. 3rd tool is RO sander.

[@petraxander4218]

I would elaborate a little. Carpentry is about three things - cutting and fastening, to create (all kind of variations of) boxes.

[@miloszivkovic6118]

@not tryna argue but Try to explain that to people that thinks im doing nothing before i actually start

[@slimdougmaddox4634]

Don't forget to measure... Or you'll be doing ALOT of cutting to trim down your cut.

[@hideandtallow]

@@slimdougmaddox4634 True, or just more and more fastening :/

[@BobboMax1]

I agree. Add safety glasses, ear plugs, a pencil, good tape measure, speed square and a 2 foot level. Pro tip for "sidewinders" (the type of saw in the video)- if you're right handed, try to find one w/ the blade on the left and vice versa. That will give you a good view of the blade as it enters the wood somewhere near your line. Also makes it easier to use the speed square as a guide.

[@TheCharleseye]

Honestly, I'd say the best advice is to learn how to use a circular saw from either side. Whether you're using a right or left side blade, you're going to end up making cuts from the opposite side (unless you want to be balancing the saw on the narrow side of the shoe). In the long run, it's best to just adapt to the saw you have.

[@dupre7416]

I finally broke down and now I have a right- and left-hand circular saw. Not a necessity, but really nice.

[@MrWolfheart111]

and dont be scared... they are quite an intimidating tool. :)

[@disqusrubbish5467]

Exactly on the saw! You can see the line and if it kicks back, it does so off to the side

[@classydays43]

Oscillating multi tools are fantastic for a number of smaller jobs. The plunge cutting function is especially versatile, and I use the sanding attachments for all sorts of smaller stuff and corners. But you've convinced me - I've been putting off getting one for the longest time, but there's a circular saw waiting for me at the store in my platform.

[@brainwashingdetergent4322]

I think you fastened (nailed) it perfectly! If an aspiring work worker really wants to see if he is truly interested or has the abilities, starting with a few cornerstone power tools is a great way to test the waters. If it doesn’t work out, he’s not out a small fortune in tools he doesn’t use.

[@Magister3eros]

Work with wood is about cutting, fastening, and finishing. You need a saw, drill and a sander.

[@rentbennett]

You can hand sand, and decks and fences don't need sanding.

[@deanslegos1990]

Ok, looks like I'll be getting that 4 speed Hilti drill, Festool random orbital and tracksaw. 👍 thanks

[@zaneorton9843]

@@rentbennett You can hand drill and saw as well?

[@brandon6173]

Sanding can be done easily by hand but I agree for larger projects sander is a must

[@brandon6173]

@@zaneorton9843 if I had to choose I'd prefer to hand sand. Over hand drill and use a hand saw. But that's personal preference each to their own. In the end it really depends on what your building..

[@Andrew-J316]

I am not a carpenter by any stretch, but my I have built and repaired many things my whole life with just the tools you mentioned plus a Dremel and a Sander. These are the only four tools I have ever really needed. Thanks for video!

[@jenniferjahns4006]

This right here is what I've been youtube and googling for a month. Like a ray of sunshine your video showed up on my recommended viewing. Thank you, thank you, thank you!

[@lakerschargers1]

I recently bought my first house and I am loving this channel. You are giving me the confidence to start tackling some projects.

[@frenchtoast5843]

I agree with your thesis, Ethan. Many years ago my spouse and I built stalls for my horses inside of an existing pole barn. I recall we used a circular saw, and a drill would have come in very handy, but we used a hammer. (LOL) Of course we had to use a shovel, a wheelbarrow and one or two other things, but basically we built the stalls with very few tools. I recently purchased a 12v cordless drill for small things I want to do around the house. I have been screening videos on how to use cordless drills as I have no experience with them. At the moment, I am still trying to figure out how to turn the "clutch control" behind the "chuck." It does not seem to want to turn one way or the other, so either I am doing something wrong, or I do not have enough strength in my hand to turn it. It is supposed to turn counter clockwise if I have the drill in my hand pointed outward in front of me, yes? I purchased a Bosch PS31-2a 12v. I did not feel I needed a larger and much heavier 18v drill for the things I want to do. I would love to be your assistant and learn how to do all sorts of carpentry work, though! Love your videos! :)

[@stargateuniverse1100]

Spot on advice, I'm a 74 year old Mother / Grandmother, I love my DIY and yes my main tools are combo 18volt cordless drill / chop saw, plus hand saw.

[@2fas4ya]

Hi Miss Hall, I’m a 55 year young mother/grandmother as well. My go to tools are the 20v DeWalt Impact drill & Skils circular saw Since the introduction of you tube I feel like I can do EVERYTHING Hence beginning MANY projects in my home - when I was younger - finishing only a few - I was working & raising kids - now retired I sure am glad I looked out for myself I do have more appreciation & patience now With a better outcome in completing my projects. Stay safe😁

[@gasiakourieh8708]

Great video!!! I started with a jigsaw and a drill. Since I only was interested in building furniture it was a better combo for me. Achieving straight cuts with a jigsaw can be done but you absolutely need to use a straight edge with every cut. I started by using the manufactured edge of a sheet of plywood for rip cuts. For cross cuts, I used a speed square. They also sell longer blades that can cut through 2x materials so that isn’t an issue. I still agree with this video. If I were doing household diy and not specifically furniture, I’d choose the same combination. People also ask me which tools to start with. I always reply exactly the same. Pick a project then buy what you need to get the job done. Simple.

[@billlauretti7963]

I agree! I'm a DIYer, and my first power tool was a Craftsman circular saw (which has lasted me 40 years!) and a corded drill (the cordless ones were a new thing and too expensive at the time). I have plenty more power tools now, but still go to the old circular saw, and now an 18V cordless drill most often (although I just bought my first cordless driver after watching your video on those).

[@roddyoccultis4266]

To me, tools are what real friends ( if they do exist) should be like. You never see them for ages and one day when you need their help, they are there for you.

[@dtbone6]

real friends....humm...where do you get them??

[@roddyoccultis4266]

@@dtbone6 You make a good point. I should have said Tools are what real friends if they do exist should be like

[@jimsmith9853]

Well said Sir. That is a great statement/observation. I am stealing it.

[@chnacr2]

You're right. I'm gonna tell my friends that they're absolute tools

[@roddyoccultis4266]

@@chnacr2 I am so glad for you

[@matt8863]

A portable table saw and a 12" compound miter saw...Because anything else your neighbor should have.

[@user-qt6uj5zp2y]

lol

[@SgtBooker44]

That was hilarious, true, but hilarious.

[@2solid4u6]

😂😭😭🔥My dude.. you play it smart and save money. 💰 while having a beer🍺 all at the same time.

[@FancyUnicorn]

Flanders

[@someonespadre]

I have a 12” slider, my favorite saw. I occasionally need a circular saw but put off replacing my old one because the miter saw is better at any cross cutting task. I use the 10” table saw 2nd most. The only thing I need a circular saw for is cutting plywood…last few times I was able to use a little powered trim saw I have which is underpowered but will cut 1/4” plywood with a fresh battery. If I worked elsewhere a circular saw would be more handy but it isn’t that hard to take the slider with me, use it on the pickup tailgate.

[@jpaugh64]

I didn't realize a skill saw could do an angled cut! That was my primary motivation for saving up for a miter saw. Thanks for helping me see the light!

[@saquist]

How can a skill saw do a miter cut?

[@planetarybeat473]

​@@saquistusing a speedsquare as a guide

[@sislertx]

My Essential list for 80 year old women... ..hammer, cordless drill, multitoo,l big ass sander...hand sander..miter saw..jig saw .i can not lift circular.saw.anymore and use it safely....and a.dremel..2 million screw.drivers..i have nail guns and i really love them..they are icing. Im.thinking maybe one of those new mini circular.saws

[@d.e.b.b5788]

Give yourself a Makita 1" hand held belt sander as a gift. I found it amazingly useful.

[@eloscuro704]

You might already have sufficient screwdrivers, but most people don't. No matter what the project, there will be a screwdriver that you really need but don't have. You can buy a set like this which covers pretty much everything: www.amazon.com/Husky-Variety-Screwdriver-Set-25-Piece/dp/B08BHTPW1P

[@willieverusethis]

I love my little Makita mini saw. I can't use the big saws any longer, but I can go all day with my little Makita. Get one!

[@d.e.b.b5788]

@@willieverusethis I've had one of those 3 1/2 inch 9.6v makita saws since the early 1990's. Amazing little tool, as long as you don't try to cut too fast, it will sliice through just about anything!

[@johannsmit3411]

I agree on you tool choice. I remember when I started 20 years ago,my motivation to get expensive Table saw,radial arm saw and more just for the convenience put financial pressure that were overcome, in time as a cabinet maker of fine furniture it made sense to get a specific tool for a specific job. Staring simple with these 2 tools leads to more improvising.

[@1ZZFE]

Thank you! I seriously think serious people, esp DIYs starting carpentry and reno works got to know channels like this. No frills, direct, and straight to the points. 👍👍👍

[@macrumpton]

Ha, I have that same exact drill! I find my jigsaw gets used a lot more than my circular saw, although having a good guide/track is essential for straight cuts with the jigsaw. The versatility of a vertical cut and ability to start a cut with a ¼" hole, and being able to cut curves, and even mount it upside down on a table to work like a bandsaw is hard to beat. My Bosch was handed down to me from my dad 20 years ago, and aside from cord replacements has needed nothing to work like new.

[@jamesanthony8438]

I'm with you on the not using the circular saw as much. I'd have to substitute the table saw for jigsaw, though. I very rarely use the jigsaw and haven't used the circular saw in about a year and a half, but the table saw gets a workout on nearly every project I do. I'm just weird, I guess. =\

[@douwkuhn8930]

I agree, but I use 2 screwdrivers. 1 for drilling & 1 for the screwing part & you don't have to swap from drill bit to screw bit. It saves a lot of time.

[@jayjayhooksch1]

Yea, I think even the most novice diy folk have figured this out, and it's why most of the big companies push the 2 tool combo kits (drill and impact driver) during their big sales. You often get the 2 tool kit for only 20 bucks more than the drill+battery kit anyways. My 'quick fix' bag always has a drill and an impact, nobody got time to be switching bits back and forth.

[@josephdestaubin7426]

That's funny, and it's the exact reason that I usually carry five cordless drills with me at all times. Well not actually on my person, but in my rig.

[@jsax01001010]

All of my projects seem to involve drilling a bunch of countersinks or counter bores in addition to pilot holes, so I'm glad I have two drills and an impact driver.

[@gondokist]

As an amateur diy woodworker, drilling a wood is very2 occasionally, i never pilot hole or kreigjig or whatever i just blast alot of screw into the wood and thats fine, diy grade fine tho 😁😁😁

[@evagore530]

have none of you ever used a flip over bit drill bit one end driver bit the other

[@samday6621]

I’m a landscape gardener and artist. My first power tools were a large circular saw, heavy duty drill and a small angle grinder. Those served me well for years.

[@highlanderes]

Agree. The third I got was a multitool. Good for an insane number of things like precision cuts, sanding, paint stripping, cutting tiles, demolition, repair work and much more I am sure.

[@path4471]

Every function of the multitool is vastly inadequate for all of those functions compared to other tools. Sander is better at sanding, saw is better at cutting, and a scrapers are better than the stripper. Multitools are nearly useless

[@LT72884]

Wife:will you build me a shelf? Me: ill need to buy a car lift, saws, and other random stuff..

[@CP-os1pc]

And my pals are coming over to help so we need beers and four pizzas

[@jukkaikomi1763]

🤣🤣🤣

[@LT72884]

@@CP-os1pc facts

[@barrybrigden7317]

LOL. Only difference, a bike lift

[@timbohouston]

Hey don't tell my secrets!

[@starryparadigm]

Thank you this is great! I’m a complete beginner with woodworking + diy and was a bit lost with where to start and what tools I actually need. A lot of diy projects on YT turn out great but they use at least 5 tools for the job

[@Madasin_Paine]

A very well made, time respectful, anecdote, experience, and rational pragmatic supported videos. Teachers take note!

[@ChrisHornberger]

I wouldn't prioritize anything else over them. They're the right choices. Next up would be the dedicated driver you mentioned - 1) alleviate frequent bit changes, and 2) cleaner drives as you mentioned. A super versatile compound sliding miter saw makes for quick repeated use at a job site, but that's convenience more than necessity. I'm building a cabin; heaviest use items so far are the nail gun (framing, 21*) and the (cordless) circular saw, with the miter saw being a lot of the bulk-cutting work on trimming studs and joists to length. $.02.

[@josephtremel5392]

Good vid. I’m a carpenter as well and I use those tools a lot. Drill can also be used to pre drill nail holes that can then be driven home with a hammer. Great for small repairs so I don’t have to unload all my tools for just a couple of nails. Important non power tools to have would be a hammer, small square, glue and at least a two ft level.

[@2bfrank657]

Great video. As a welder/fabricator I'd suggest that the equivalent for metalwork would be a 125mm angle grinder + drill (assuming you also have access to a welder). Can do a huge amount of fabrication work with just those two tools.

[@2bfrank657]

@Bamboo Training absolutely you can. There are plenty of risks to be aware of, but so long as you read up on these then you can absolutely teach yourself. Just don't think that being able to stick two pieces of metal together means you're ok to do critical welds like structural stuff.

[@2bfrank657]

@Bamboo Training That stuff should be fine, just think "what would happen if my weld fails" and that should guide you. Watch some videos on welding safety, make sure you have good ventilation, don't weld near flammable stuff, buy the right safety equipment, etc.

[@TEXAS.N8V]

I dig your videos! I've only been in framing since 2004, never rose up the ranks in a crew, but i'm a good cutter, now running my own contracting business of 3 years and always learning more, thanks to videos like yours.

[@manilamartin1001]

This is great to see. I started off framing houses in the 80s. I pretty much just worked for 1 year but I got the bug. Nice to see a pro talk about tools.

[@ipick4fun27]

I agree on the circular saw and drill. Ever since I use the impact driver, it's a must have. Beside, they sell them as combo. Drill itself cost almost as much as combo. Kinda hard to do without the mitre saw. It's fast and convenient and takes lots of setup from circular saw to do the same thing. I would say they are quite different. If you can't afford a sliding, just do the one without. It goes lot faster because when patience runs low, people get sloppy and injuries happen. Low end mitre cost ~$100. Just put a crowbar to the wallet. Don't cheap out on necessities.

[@johnduffy6546]

I really appreciate your frugality. Our ancestors made great things without the convenience of today's gizmos...Elbow grease still works as well today as it did a thousand years ago. Keep doin what you're doin!

[@kempkennedy3542]

I have been buying up tools like crazy since I started renovating my kitchen by myself. I bought a portable table saw (as opposed to the circular saw) and it has been invaluable for use. Problem with it is storage and I could have used the circular for faster, more accurate cut removal of subfloor. Great video and I know you are keeping it super simple, but I can say that my "saw's all" reciprocating saw and the little multi-tool have been handy for multiple occasions in the house.

[@Oldtimecarpenter]

Without doubt you hit the nail on the head! That’s a perfect starting place every person needs to know about. Anything more right now would only confuse most beginners. I’ve seen some of your videos and I’m impressed with your knowledge and skills. Myself, I’ve only been a carpenter/cabinetmaker for the past 50 years and still learning. Keep up the good content and thanks for sharing!

[@TheHonestCarpenter]

Thank you, Pete! I love hearing from long-time carpenters/woodworkers like yourself! My grandfather was a master cabinetmaker--also made custom doors and windows in the 50s and 60s. I've never gone that far down the cabinet road, but I always admire that work. It's a cross between carpentry and woodworking, and takes perfect precision carried on a large-scale. Thank you for watching and writing in!

[@mrmrlee]

Agreed on the drill, for general around the house work I use a reciprocating saw more than a circular saw. In the hands of a skilled operator a reciprocating saw can be both jigsaw, chop saw, and circular saw for carpentry work whereas a circular saw is not very useful for demolition work or plumbing.

[@MFTomp09]

Ehhhh. A circular saw makes better straight cuts. The longer the cut, the better a circular saw becomes if you want it to be straight. If that precision isn’t required then a reciprocating saw is a welcome addition to a tool collection. But all the projects I’ve done for or around my house I’ve wanted more precise cutting ability than I feel a reciprocating saw can provide. I don’t even own a reciprocating saw and I have no plans to buy one because I have no need. If I have a spot that the circular saw can’t get into, say to cut a pipe inside a wall somewhere, I have an 8 inch electric chainsaw I bought for trimming tree branches I’m sure could do the job.

[@ysunsolicitedopinion202]

This is the exact information I have been looking for regarding saws. I'm a grandmother..almost 80..I have been obsessed with designing and making items for small spaces. Most of my materials I pick up on trash day, Habitat and thrift stores. Re-purposing is something I have done since I was a kid. I used to follow my grandmother around and we would " invent" things from other things. She was born I. 1870s and did that all her life. My father followed I. Her footsteps, as I am close behind. I find the issue is working in a safe manner. What do you suggest for bare necessities ? Ie: saw horse? Yesterday I struggled with a saw and wood balanced between my legs! Yikes! Now I know my two most important tools. What other things do you suggest? I can't tell you how many tape measures I have lost! Lol..I hired neighbor kid to follow me with a video recorder and to pick up my tape measures! Loved your video. Looking forward to watching more.

[@QoraxAudio]

The most important power tool I have is the soldering iron. Used it on almost every home appliance I've repaired so far. Also made a nice penny on the side by repairing vintage radios, amplifiers and turntables.

[@joeygordon7265]

What about your multimeter? Would you say you use that more than the soldering iron?

[@QoraxAudio]

@@joeygordon7265 I don't know if a multimeter counts as a powertool.

[@chatteyj]

@@QoraxAudio The only power tool I need is down my pants. Ba-dum chish.

[@klausreviewscraftrestore3152]

i have to keep this video away from my wife...or its the end of my tool collection.

[@kan-zee]

LMAO....to true..LOL 😂🤣👍

[@jayjayhooksch1]

I just don't let me wife look at my tool collection; if she saw how clean my cordless nailers were (from lack of hard use) and knew how much they cost i'd be a dead man lol

[@amillerinspections1332]

Amen brother, puhreach it!

[@sirlorddoctormajorphd3016]

Tell her she only needs to inspect 1 tool 😏

[@kathryncastanares525]

@Sean Steele although i no longer wear make up aside from mascara. I found many men tend to complain about the expenses of a womans hygienic process, to then complain when they no longer get all "primped and pretty". Its hard for each sex to understand the needs and wants of the others. I dont find women need a huge collection of purses or shoes. But facial products and make up is something they use to continue looking pretty for their husband. Idk any man that is happy with a woman who doesnt do anything with herself. And i dont know many women who is happy to have a man that can't build/fix things. Which both requires some expenses to facilitate. Its when either side has no self control and over spends or hoards things that go unused where there may be a problem. Especially when/if it starts to affect your financial or marital situation. Aside from that, if thats not an issue, how about lets just live and let live? I am happy that my husband has a collection of tools since he not only has the ability to fix/build things we need for our home, but i also get to barrow them for any work i need done in our veg garden.

[@martinrivera6770]

Started with a Ryobi circular saw my wife gifted me for our first Christmas a few months married, that kicked off a new hobby for me that turned out to become a passion. My first project was cutting a set of large 6x12” domino pieces for playing in the lawn. I didn’t even have a workbench, I used the lowered door of the truck bed to lay out my 1/2” thick sheets of plywood and got to work. Sanded all pieces by hand, stained them, cut out a stencil out of cardboard for the dots and spray painted them. Still have them and now kids play with them. Several years forward, that circular saw has been used in literally EVERY project ever since.

[@juancarlosrodriguez6402]

I think a jig saw is a good alternative to the circular saw. When you live in an apartment you dont have enough room to build things but you still can do some repairements and some small projects with the jig saw. With a good guide you can make straight cuts with the jig saw.

[@Zerbasst]

yes! You can also make rounded cuts. I'd say: start with a jig and a drill, then add a router and a circular saw next in that order. After that comes electrical planing, which can also be done by hand for a long time. Everything after that is just bc its more comfortable to use or for bigger workpieces :)

[@kdc-nb5fw]

I agree. I use a jigsaw mainly because it is safer. Also, if you are a beginner, don't use a drill that is too powerful. They are more dangerous than people think.

[@monalisahota]

I have made 100% of my projects with my Skill saw, along with an electric planer, a chisel and a Dremel which I occasionally use to bring some level of perfection to the imperfect cuts. Have been very pleased with the joinery even. I just finished making an end table from cutting up an old door and have made some cabinet like things too. I rip boards to width and thickness but that is very very challenging. Every single rip is a creative problem solving exercise 😃. Making rabets is becoming an impossible task with this saw though as I am out of ideas on how to get a clean line in a rabet. And that's what is making me consider a table saw now. It will certainly make my life easier and make projects move faster. Good to know someone else also uses a circular saw for most of their projects.

[@someonespadre]

People practically give away old table saws on Facebook marketplace.

[@monalisahota]

@@someonespadre do you think I'd find a DeWalt 7491 RS for free or almost free?

[@someonespadre]

@@monalisahota go for an old Craftsman or Wards Powercraft. 1960s. My 10” Craftsman is circa 1980 but still decent quality.

[@monalisahota]

@@someonespadre I thought about this as I found some old ones somewhere. But as a first timer, I'd prefer something whose parts and still available easily and something that I can trouble shoot easily. May be later

[@MG-wx8yx]

I'm new DIYer (not yet made anything), today is the first time I held a circular-saw. After reading the title of this video, I immediately asked myself, what are the 2 most useful power tools other than a circular-saw and an impact driller driver. And I was right. But I have to say I have learned a significant amount of things in this playlist. Thank you so much.

[@etownandrewg]

I agree. Before I heard what you were going to say, my guess was a circular saw and drill.

[@mikegillis22]

... and the 3rd? Router... 4th, sawzall...

[@harrysample5600]

I agree, I came down in favour of Combi drill and Circ saw. Then I was 50:50 if I would swap the circ saw for a jigsaw and make do. Depend how much sheet material you’re working with versus doing more detailed work/ small bodges.

[@renevank]

Personally I'm really fond of my dremel as well, but I use it for a lot of smaller DIY projects, combined with 3d printing. Cool video!

[@khanscombe619]

I agree. I will add that U can get table kits to use your nice circular say upside down like a makeshift take or add guides to use miter jigs, Some drills can be fitted into a drill-press kit if needed. But mostly, if it's for work or side income hobby, upgrade as U go based on what parts can use help & yet pay itself back. In the end, yes, quality builds will make U want to work more as they last longer. Some may help speed up work making more money as well. My 1st home tools was a 7" Skill corded and a BluePoint (sold by Snap-On) corded. I still have both after replacing brushes but good to go even though I've moved to Makita Li-Ion, had old Dewalt NiCad.

[@nicksalazar2239]

As soon as i started the video i said "its got to be a circular saw and a drill" i was right!! Very good advice!

[@davidkidd2961]

30 years as a carpenter/ handyman, exactly what I said. I picked Makita circular and actually a corded drill. Battery drills are great, but you still have to recharge batteries often. Even having 3 or 4 batteries, you can still end up having to wait on one to finish charging.

[@fattony8803]

I just started my cordless tool collection. These two were my must have's. Great video!

[@rayanderson931]

My first house reno (quite a major rebuild) was in the early 1980s. I had no power tools. I used a hand saw and I had a 2 speed 1/2 inch hand drill, a hammer and roofing square, a level, a plane and a few other cheap hand tools.. All my framing was hand cut, as was my finishing timber. A sander was a block of 2 by 4 and a roll of sandpaper (still is). It was fun and I learnt a lot. I am now on my fifth house reno, I have a huge number of power tools, and the job is a lot easier, but I still use a lot of my old hand tools because they can do the job better.

[@AndrewTheFrank]

Been doing some DIY stuff around the house for the last year or two and I'd have to agree with the advice of this video. I have less than a dozen cord and cordless power tools to choose from and its the two mentioned that are my initial go to tools for most every situation.

[@juanmolina7894]

Great review for beginners... I Almost agree with Your tool choice... Me, a beginner DIY in woodworking, I started woodworking with manual hand-tools, manual hand saws, chisels, a stanley manual miter saw, a couple of hand planes (a #4 and a #5), an old hand-drill (with good drill-bits)... I would just add another power tool to Your list... a 1/4 th sheet electrical sander... not the round one, they do not reach square corners.. a simple one... and no need to buy special round sand-paper... the sanding results are great and most of us, beginners, start with cheap wood, or pallets... and a well sanded pallet looks great. Most of my little things I do in wood, no-one believes I made them with pallet wood, specially if I add a stain to them...

[@craigsmith9876]

No totally agree they are always my go to tools when I do any DIY. I like to have 3 "value" 18V drill drivers 1 for drilling, 2 for countersinking and 3 for screwing. The circular saw saves so much time

[@hardlyb]

When I saw the title I thought, 'circular saw and cordless drill'. I have too many tools - I'm a tool junky. But despite generally having 'just the right tool for the job', I often do jobs with a circular saw and a drill. And I use a cordless circular saw these days; I'm amazed at how powerful they are now.

[@danielch6662]

Even with a keyless chuck, after you've switched the 20th time between the drill bit and driver bit, you'd be wishing you had a second drill or impact driver.

[@jonathanleslie9100]

I actually keep 3 handy at all times, the pilot hole, he recess bore, and the screw bit. I actually just ordered just a keyless chuck without a drill so I can hand bore out a recess without fear of powering through the whole piece of wood.

[@mitchelljermaine]

@@jonathanleslie9100 Same here. Still waiting for someone to invent a 3 way chuck so I can switch between bits without having to switch drills.

[@willkrull7316]

Funny, I had that very problem today installing a new screen door. NEVER AGAIN. Hammer drill+impact driver=problem solved

[@LemmingFNSR]

Daniel, hi from Oz. The 2 tradies who installed two security screen doors and a shower screen had 4 drills, all with different bits/drivers. 20 minutes total time. I think they were onto something.....

[@inspired4more]

Bit holders are cheap

[@HandCraftedPT]

Learned a lot from this video. I don’t know much but I have a lot of projects I need to do as we priced them out and they are expensive from drywall to trim work. I was just looking at all the saws today at a local big box store and just felt overwhelmed. Thank you for this great info.

[@Mitsaras1973]

Correct in choices. Problem is make suggestions "most pros use". Being in carpentry and general construction my entire life, the prevelant saw utilized by pros, would be the tried and true Skilsaw. Also, nowadays, with the different types of bits geared towards impacts drivers, a good 18v impact driver would be better than a standard drill/driver.

[@christopherdean6150]

Agree. I wouldn’t trade my Skilsaw’s for a Makita any day. Not saying Makita isn’t good. Not even close to being the standard of a Skilsaw worm drive.

[@henri6595]

What do you think about the M18 Fuel 7-1/2 inch circular saw rear handle? Been thinking about getting one if they ever go on sale.

[@toemas8]

As someone that owns a circular saw I think a table saw is great for DIY’ers. It can mitre architraves, rip accurately and there is less set up time. It makes up for errors us DIYers can make and portability isn’t as important to professionals. The circular saw is better where you need to take the tool closer to the work area.

[@lachlanbell8390]

After using a borrowed table saw, one thing I really notice with the circular saw is the inability to adjust the cut depth. I just picked up a multitool, but before that it was back to a handsaw for every shallow cut I needed to make.

[@toemas8]

@@lachlanbell8390 with both table saws and skill saws you adjust the depth .

[@lachlanbell8390]

@@toemas8 That's what I mean - when I was using a borrowed table saw, I was able to make long, shallow cuts, which I couldn't do with the circular saw after returning my friend's table saw.

[@kevinlawes591]

I used to work for a joinery company but 3 years ago work dried up!! Since then been on my own! I have a handtool selection which works for me! Power tool wise I run a mitre saw, circular saw, and electric planer! Truth be told the circular saw is the one tool I could not be without❤️

[@geraldgroulx6937]

Here in Buffalo, NY we've enjoyed the services of a tool library that is "manned" by really dedicated volunteers. It's become super-organized, including showing the status and pictures of available tools which can generally be checked out for a week (or longer for lower-demand tools), all for 20 bucks a year. COVID has affected their hours and practices, easing up somewhat lately as the virus has receded. Community gardens and cleanups have become a part of their mission. Result: Available tools without the big cost or storage....Gerald

[@Musecrafter]

I need three power tools: a skil saw, drill, and a sawzall to tear down the colossal mess I just made ;)

[@jonnybass6226]

yeah i love my sawzall too

[@tribulationprepper787]

Funny in a "true" kind of way.

[@tribulationprepper787]

@G Galilei I went for the DeWalt battery powered version. Seems to have enough "Oomph" to do the job. Nice to be able to take it across the property without a 300 foot cord trailing behind me.

[@PeaceLoveAndHarmny]

I'm covered then! TY

[@patriciabass9502]

I hear ya

[@joukohahkio8210]

I did my first project ever with the two tools. I bought DeWalt corded circular saw from a discount sale, and the Hilti 18 volt drill / driver in a similar manner. It wasn't perfect, but close enough and I got the job done. All the additional tools after that just increased comfort and speed, mostly.

[@TraffordTrevorrow]

More of a mechanic guy but when I saw this in my head I thought an impact driver and an angle grinder. Little different but kinda the same thing, something to cut and something to drill/loosen things.

[@AnonymousAkira]

Nice, the first power tools I ever bought was a DeWalt drill and saw combo set. I still have the saw (drill died on me after a decade of light use) and the case they came with. Saw is still running fine too :)

[@tomowens7301]

I agree. I have done alot with just a drill and circular saw. But I would add a 3rd power tool to that, and that is a finishing pad sander. But as I have been growing my tool collection, and types of projects. Having other types are very convenient, and save on time.

[@johnkelley9877]

I have done a lot work around my home and family members homes and in the end I always used the circular saw and cordless drill with a clutch. I have installed doors, trim work and even built a wheelchair ramp with just these two power tools. I agree the circular saw can be dangerous if you do not pay attention to the cut. For dimensional lumber I use a speed square to keep the cut line straight. Thanks for sharing this.

[@NunYa953]

This is blasphemy. Every married man knows that the only thing that makes building your wife a new dresser every 2 years based on the current trends is the excuse to spend ridiculous amounts of money on tools you don't really need. Even doing that is less expensive that buying the furniture at Crate and Barrel.

[@GlennMBrown1]

Well how else are you gonna follow the youtube videos if you don't use the same tools they have??? ;)

[@jamesschreiber9857]

I really thought I was the only one doing this and I felt bad like I screwed up but I guess I’ve been following the code all along

[@catsrus-es9eu]

😅😅😅

[@davidaramburu4440]

jajajajajajajaja, tienes toda la razon

[@sparkythesecretsquirrel4013]

Plus you can make her dresser from crates and barrels.

[@kinderliving1]

Thank you so much for this video. I am just starting down the road of DYI (late to the game) and this is exactly what I have been thinking about - what tools should I buy first. I really, really appreciate your honesty and I'm glad I have now just found your channel.

[@Lew114]

As a novice I’d love to see more on safety.

[@sbradshaw1886]

Look through his video collection and Subscribe. There are plenty.

[@thequietkiwi]

Safety third!!!

[@GSL4396]

Me too. Kind of scare of those saws.

[@zoltantapai3716]

If I wanted to go for some speed and long cuts I would definetly go with the circular saw as suggested but I recently rediscovered my jigsaw and it is quite amazing how accurate it can be with some practice and patience. Also I would go for a hammer drill for masonry applications.

[@SnootchieBootchies27]

Most of those 1/2" cordless drills that he's talking about have a hammer function. I wouldn't use it for lots of heavy concrete drilling, but it will put a hole in grout or brick quick and easy.

[@wayneyadams]

I have a cordless hammer drill which sits on a shelf gathering dust because it can't compete with my corded hammer drill. Cordless hammer drills just don't have the power of the corded models for drilling into concrete.

[@PhillipHilton]

Thank you very much for this video sir. This gives me hope. I'm based out of Singapore and a 'corporate stooge' who is stuck in an apartment - no shed or garage to tinker in. To be totally honest because of covid its been a year and a half of ''4 walls and zoom calls" which - and I'm sure its the same for most of us - has absolutely sucked. However, left to my own devices I made lemonade out of the lemons the universe gave us. I found projects and started making things. Initially electronics(irrigation systems, custom audio devices, IoT stuff) and then I began modifyingexisting furniture to do other things(IKEA side tables into mini server racks, picture frames with magic mirrors, etc.). But I've had a problem while I've got a decent drill/driver and some basic hand tools I haven't been able to cut and shape lumber. The advice I was given 'up until now' was 'buy a million and one specialist tools' or your output will suck. Sadly I have neither the space nor inclination to outfit a full workshop BUT what I do have is decent weather all year round, a balcony with a power source, a couple of decent vices and an outdoor table so maybe...just maybe with a circular saw and some decent guides I can start upping my game and making more complex pieces. Food for thought...thanks again.

[@andreacastleberry978]

My granddaddy built houses for many years with limited power tools and a third-grade education. Some of my earliest memories of him are with circular saws and hammers. (I had sensitive ears. 😂) My parents still live in one of those houses he built about 35 years ago. Thanks for this awesome video! My two sons have recently started woodworking, and I’m glad to know the old standard tools are still the best tools to get you going.

[@DoubleQz]

Thanks i just bought a cicular, it arrives today. Watching how to videos and will definitely read the manual through and through.

[@royhoco5748]

what tools does a man need ? every tool he can afford to buy.

[@misskim2058]

Women, too.

[@Joel_E]

It's always "just one more."

[@royhoco5748]

@The Next Chapter you don't have enough shoes, you need to go shoe shopping.

[@stevepowsinger733]

Never forget what a man's best tool is. Use it wisely and remember it can break or get damaged through misuse or overuse.

[@MintStiles]

@@misskim2058 OMG hahahaha

[@shellymillerleer]

This was so great. I'm getting ready to teach older women how to use some power tools. Thank you. I subscribed to your channel.

[@dottyjyoung]

AWESOME! Sincerely, an older woman who is starting a remodeling biz.

[@milesmccall2301]

Honestly, a circular saw is probably a terrible thing to hand to an elderly person who is just learning power tools. Arm strength, grip strength, and reflexes are essential for handling a circ saw safely (especially if something goes wrong). I'd really suggest an oscillating tool or a table mounted saw instead.

[@shellymillerleer]

@@milesmccall2301 I wouldn't say 'elderly'. But we're not spring chickens. Surprisingly strong and mighty. It just keeps getting better. Thanks for the tip.

[@atteroljones6936]

I once went to a private homeowner's shop to cut rails for my deck. For a fee he would guide you through the process of using his wood cutting machinery. Two older women were at the shop at the same time, one a retired doctor and the other her friend. Weeks before the doctor had cut off the tip of a finger while using her own equipment in her new woodworking shop. Sort of learning curve....

[@themoonsbluelight]

I have had the same Makita 5007F for about 20 years, and used it framing houses professionally for years. Still runs great. My old man has the same one and has had it for nearly double the time I have had mine.

[@kasbakgaming]

I think there's a balancing factor between going for a circular saw or a table saw first as a DIYer. As mentioned, the first is safety; I think it's a lot easier for a novice to use a tablesaw safely when compared to a circular saw, especially if all the safety guards are in place like the blade guard and riving knife (that said, danger is always present if you use a tool improperly). If it's a hobby you're looking to get into but have absolutely no experience, then start with the tool you can feel the safest using while you get used to it, then move up to tools that need more experience to use properly but will get the job done easier later. Second is what types of projects you're working on. If you're doing a lot of work with sheet goods and/or larger, rougher construction projects like decks and framing, then yeah, a circular saw is the way to go. But if your focus is more on small, finer projects like furniture, shelves, boxes, etc., then you'll end up with better cuts and thus less finishing work to do with a table saw.

[@dmyt58]

Just get a tracksaw instead of a circular saw. Fixes the danger issue and upgrades the circular saw massively

[@worldtraveler8571]

You can tun a circular saw into more with guides

[@gregorsamsa1364]

Table saws are actually the most dangerous

[@Reapsin]

I am a novice DIYer, and this may not mean much to a lot of people, BUT; A circular saw is a great time saver, but I wouldn't call it essential. Anything you can do with a circular saw, you can do with a hand saw. The biggest thing to consider is time, when deciding this purchase. One thing to note; know what tooth pattern to use for the job when selecting a hand saw. The variations in tooth pattern make a world of difference in cutting! I would consider the drill essential, though, as hand drills are very difficult (competitively) to source bits for. And the range of bits is far less viable for many projects (drivers, augers, spades, etc.). The extra utility built into one tool makes it well worth the investment!

[@NWGR]

I've been woodworking for 16 years now; I would most definitely consider a circular saw essential. Ripping down a few sheets of plywood to build even a couple of cabinets is not something I'd want to do with a handsaw.

[@jackylzimmer3954]

This video is about essential POWER tools.

[@marsinbako8491]

No way I’m using a handsaw if I have a circular saw.

[@janderson8401]

@@marsinbako8491 if it’s only one cut I’ll just use a hand saw. Less set up, faster, quieter, and the dust drops down instead of getting thrown into the air for me to breath.The answer might be different if I ever get a cordless circular saw

[@MichaelDawson03]

Before you gave named the two, I called them out. I completely agree. They were my first two purchases. I bought what I could afford, and I have upgraded both, but they still get used a ton. I am only a DIYer and do find myself using my Compound Sliding Miter saw more often than my circular saw. I also find myself using my impact driver more than my drill. However, as you said, I could do away with those two tools and still have all my needs met with the drill and circular saw. I do love my table saw though, I wouldn't want to do without it.

[@jaibruce777]

On steelworks: Angle Grinder & Welding Machine.

[@roteguard]

Great info, I’m interested in getting started woodworking & would love to see a series of videos dedicated to safety

[@howlme]

Steel toe shoes/boots and eye protection first, then ear and dust mask (not N95 needed). Good luck

[@jeffpowers1979]

Dito !!! Know about kick back !! I now own 7 circular saws. all set up for cutting different items. Love every one of them and use a rip guide for all of them. Makita 3-1/2 " wet saw for glass, tile and Marble,1978 Dewalt Saw Cat with a dust collection fitting I put on the guard, for my panel saw table Still works! 1985 Super Saw Cat carbide blades / wood. 18V Ridgid PVC and plastics, Skill Saw set up for concrete, tile and Hardy Board, etc. 24 V Ridgid for the jobs and an old 8" Guild Saw for decks and framing, from the 1950s . All great saws. I am a 71 year old master carpenter retired and renovating my own property right now. Love your video ! The only other tool I would add today would have to be a multitool I just can't live without one anymore ! LOL ! I bought mine at a trade show in the 1980's. It's a Fein, made in Germany and still works. 😳😳😳😳😳😳😳😳🤓😎

[@rico1319]

I totally agree with you, especially for the group of folks you’re targeting! Another video with honest info!, 👍👍👍😎🇨🇱