Yz450F Top and Bottom End Rebuild - Pt 3 Assembly

Part 3/3 of 2016 yz450 rebuild. Finishing bottom end and top end plus startup
Hope this adds value and helps someone else out there that needs to do this Work. If it helped you please Like Share & Subscribe!
Rebuild Kit - www.ebay.com/i....
Music : 1st song - All Night by Ikson / ikson Music promoted by Audio Library • All Night - Ikson (No ...
2nd Song - Daniel Groza
********
Thumbnail: Iphone
********
Camera : GoPro Hero 8 black
********
Editing : IMovie
********
Project bike: 2016 YZ450F Fuel injected

[@slavsquad]

@Howard Tayler I saw your comment in notifications but it’s not posted by KZbin 🤷🏻‍♂️ but thank you for the support and I’ll check out that website!

[@92rellab]

Im going to do the crank on my 03 yz450 i know these years are different but was watching to get an idea and i think i can handle it ....i have the service repair manual

[@slavsquad]

It’s really not that difficult. Just take your time. Take pictures

[@P1toman]

I have a 2010 yz450f crankcase broke Someone know if I can use any another model year (bottom end fits)

[@JuanOrtiz-wj4rc]

That song sounds like my girl Stacy Latisaw let me be your angel

[@socalgix]

Hi so what was the verdict? Bad crank? I have a 2016 and found a bunch of aluminum bits in the oil screen. Has me worried.

[@slavsquad]

The shavings for me were my own fault for drilling and fixing one of the case half’s after chain went through the case. I believe it then seized the crank. Possibly clogged the oil pump and didn’t get oil to the crank. Run oil through a few times and see if you still have the shavings🤷🏻‍♂️

[@TaxationIsTheft439]

How is that 7.2 foot pounds with a drill

[@slavsquad]

Drill is used to screw in faster. Then it’s done by hand

[@TaxationIsTheft439]

I figured so. You just did this job following the manual ?

[@slavsquad]

@@TaxationIsTheft439 pretty much yes. I didn’t have the Manuel but I got info from people who did

[@shanemckenzie6653]

Would I necessarily need a torque wrench?

[@slavsquad]

Hi Shane. In my opinion If your working on a more expensive bike then it’s definitely necessary. Something as simple as over tightening or under tightening can cost you a lot of money in the long run. I will say that when I was younger I never used one on my little pit bikes and haven’t had an issue but it’s not the smartest way to go. When it comes to exterior I don’t stress to much about a torque wrench Torque wretches are quite easy to get your hands on if you have an o’Reillys in your town or a auto parts store that offer rentals. O’Reillys lets you rent it it but they return your money once you bring the tool back.

[@76tigga]

Torque wrenches are a must if you are going to do your own maintenance. Every time I remove the wheels on my car, I would use a large torque wrench and torque the lug nuts to spec. Buy a small and a large one. The small ones go up to 30 ft/lb. The large ones go from 30 to 150 fl/lbs. I use the large one way more often than the small one. They are a good investment are relatively cheap.

[@Jason-zr6il]

What’s supposed to be the count between intake and exhaust pin line up?

[@slavsquad]

Are you Talking about the Dal pins? When putting the head back on the block? If so, there should be 2 in between the cylinder and block and another 2 i between the cylinder and head

[@NickDmax]

Hey what kinda of grease did you use in the head bolts?

[@slavsquad]

I used a general assembly lube for the rebuild. I don’t remember using any grease on the head bolts.

[@outbackboyz6127]

Hey I have a question I got this lil pin I found in the inside of my motor I’m trynna figure at where it came from

[@slavsquad]

Hmm interesting. What does it look like

[@dannyfranklin434]

How did the Hot rods crankshaft hold up? I have a 09 yz450f I’m going to rebuild

[@slavsquad]

So far so good. Been holding up strong

[@treverlechnyr7401]

Where did you get the blue peace that the radiator hose goes into right above the cylinder?????

[@slavsquad]

That’s an aftermarket piece. I bought the bike with it so unfortunately I don’t know where it came from but I believe it’s a Boyesen part

[@tnort101]

@@slavsquad the blue thing is a thermostat from C3 powersports. Snowbike parts, snowbikes are hard on motors it’s why that one blew up and why I’m watching this video 😂

[@slavsquad]

@@tnort101 makes a lot of sense lol now that I think about it I remember this was a snow bike before I ever bought it.

[@RIZKYARISSANDY-yn3ty]

Nama lagu apa bang

[@SandorVeres]

0:07 red oil name??

[@slavsquad]

It’s called yamalube

[@slavsquad]

Hey sorry mixed up the oil names. The red assembly lube is “red line synthetic oil assembly lube”

[@shanemckenzie6653]

Hey I have a question

[@slavsquad]

What’s up?

[@dillonmckinney8348]

really want ask a few qustions ah via facebook or whatever

[@slavsquad]

I don’t have FB. Disabled it a couple year’s ago but I still have fb messenger