It is useful to know this - Charge Different Batteries with TP4056

[@anti-popfpv4638]

Love it! Just ordered 20. I love flying drones and this really helps make custom battery packs. Your work is loved and respected, I hope you're making the money.

[@hemanthkumar5438]

T4056 uses linear regulation. Meaning anything greater than 1Amp makes it extremely hot.

[@andreascandra2603]

just using a small heatsink, its simple & work very well

[@AndreyChugay]

The most interesting thing for me is that all the videos show how they launch this board with 5+ volts, but no one shows that it works better with 4.4v with lower heating.

[@oynamalan]

Be that as it may, You can find 5V USB supply pretty much everywhere. You can't find 4.4v though.

[@mikebond6328]

Apples and oranges.

[@artled]

Спасибо! Возьму на заметку!👍

[@nicedick4697]

возьми в рот

[@NaNguyễnthị-k6z]

His video is very much clarified!

[@keenowl1410]

Great video again.

[@васяпупкин-ю7э]

Zafer, красавчег!

[@ДаниилЕрошенко-н8э]

You have a regulated power supply, using it you can easily charge any battery...

[@yanleo3434]

It's two different things by myself.1st only adjustable power source,2nd circuit board which knows (programed) how to charge Li ion battery correct)

[@mikebond6328]

The power supply won’t stop charging when the battery is fully charged.

[@clausqp]

@@mikebond6328 actually it will! if you set the voltage to 4.2 it will stop there :)

[@sanfrrraa]

​@@clausqp no it doesn't

[@clausqp]

@@sanfrrraa Can you explain why not? Because as I understand it two devices with no potential difference will give no current flow, or maybe I'm wrong?

[@serferinterneta]

Спасибо. Хорошее видео. Очень полезно.Thank you. Good video. Very helpful.

[@ZAFERYILDIZ52]

Спасибо за ваш комментарий и поддержку.

[@СергійЯловенко-е7з]

Технічно відео не коректне !!!

[@mikebond6328]

@@СергійЯловенко-е7зWhy?

[@vinnica404]

To reduce the heat dissipation of the 4056 chip, you need to apply no more than 4.6-4.8 Volts to the input. 🖖

[@voyt777]

Przy prądzie 1A układ TP4056 grzeje się mocno, nie warto przekraczać tej wartości bo długo to nie popracuje.// At a current of 1A, the TP4056 system heats up a lot, it is not worth exceeding this value because it will not work for long

[@mikebond6328]

It will not work for long hot glued to a piece of wood but if there is space under the module for air circulation and maybe even a fan it will stay cool and work for a long time.

[@RixtronixLAB]

Creative video, thanks :)

[@khoaimo81]

That Good and Number one for you ❤❤❤❤

[@ZAFERYILDIZ52]

Thank you very much for your comment and support.

[@nannatv9264]

Thank you for letting me know useful information.

[@attilarivera]

Thank You!!!!!!!!!! 💚💛💙🤍

[@Angkasa_Berkah]

ilmu yang sangat bermanfaat, terima kasih videonya bagus

[@frank67628]

Whow !!!! you are great !!! many thanks Zafer!!!!

[@rovshangaraeyev]

Çox sağol Zafer Yıldız.

[@TalismancerM]

Thanks. I didn't realise one of those pads was just GND. Much easier than trying to connect to 2 SMD pads.

[@artursmyrek7987]

Thanks for video 🙂 Could You make more videos about such circuits Mr Zalpher?

[@МаршолаКашакоф]

Я совсем не знаю ихние язык, но я хорошо понял что он имеет ввиду! Теперь мне кажется что я знаю его язык. Мне как раз пригодился этот способ Я слегка понизил потребление заряда. благодарю автор за информацию!⭐⭐⭐⭐⭐

[@vipalsharma4120]

THANKS, ZAFAR IS BOSS IN ELECTRONICS👍

[@dalevard693]

Thanks! You inspired me, I'm already ordering components.

[@solarEnergy-777]

Wow . How simple! Thank you!

[@husnukar1400]

Teşekkürler. 👏👏👏

[@azlirameliasdasilva4662]

O que não diz o vídeo, se houver uma falha no potenciômetro no caso o trimpot por um momento seguer o ci terá corrente máxima excedendo o suportado e queimará, por isso no projeto é um resistor fixo, mas com um arranjo simples em chavear outros resistores em paralelo isola totalmente um provável incidente...

[@ZAFERYILDIZ52]

👍❤

[@azlirameliasdasilva4662]

@@ZAFERYILDIZ52 vi um vídeo há alguns anos gringo que fez com um potenciômetro e daí momento houve uma falha deixando o circuito aberto sem resistência o CI adota corrente máxima e queima...

[@matssonGamer1184]

​@@ZAFERYILDIZ52você é português??

[@mikebond6328]

A fixed resistor should be used in series with the trimpot to limit the maximum current.

[@user_best666]

последовательно ставишь 1,2 ком и все

[@alexps6463]

Clamping a board over its components (0:08) is not a very good idea.

[@electproject]

Good job ever

[@arduinomaquinas]

Também gostei Luiz, valeu 😉👍

[@tibib4029]

Puedes modificar el voltaje de carga/descarga ? Para usar la bateria entre 20%-80% (3,5v-4v?) Seria interesante un video asi

[@petrpetrov8562]

Видео 👍 пожалуй скачаю .

[@garekon]

Excelente la explicación sobre tradear BTC con otros pares y viceversa. Saludos

[@Kipperleader]

Если питать от лабораторника, то питание лучше выставить 4.5В, будет меньше нагрев.

[@alexps6463]

Если регулятор может работать нормально с падением 0.3В, то да

[@Kipperleader]

@@alexps6463то линейный преобразователь, при 4.5 гарантированно все испытуемые платы нормально работали, отдельные экземпляры даже при 4,3 нормально заряжали.

[@misterpacoalaparato]

I miss you measuring output voltage.

[@johnbauer9223]

He didn't, after reading some of the comments I will be testing to see after I change the resistor.

[@VINAYAK.VINAYAK.]

Super Video Sir Amazing

[@oscarzamora2911]

Puedes desmontar la resistencia variable, medirla y sustituir la resistencia por una smd fija y quedará más curioso. Gracias X tu

[@mikebond6328]

There is a chart for the tp4056 that shows how much resistance to use for specific amperage. You can find it on google.

[@EFDawahWiseHamzasLantern]

brother i want to charge my batteries up to 4v instead of 4.2 using tp4056 pls help

[@ambalangodachandrasiri6361]

Excellent job

[@user-maikl-161]

Спасибо за видео, дёшево и сердито. Будем использовать.

[@sakirmaraz7200]

Zafer bey voltaj ayarını nasıl yapabiliriz örnek olarak lifepo4 pil şarj etmek istiyorum

[@johnbauer9223]

Me too

[@kamranashabi8952]

great thanks

[@elhatillanodigital5011]

I need to fabricate an 8 AA cells battery charger, sny idea on what module or circuit could I use.?

[@arkaocozocoz6513]

Sangat keren 👍👍👍

[@CLEVERCAT-iq4kt]

i think TP4056 will be ultra hot if you rise the charging current

[@ZAFERYILDIZ52]

Evet 1.3 amperin üzerine çıkmayın hatta soğutucu ekleyin

[@ZAFERYILDIZ52]

Yes, do not exceed 1.3 amps and even add cooler.

[@lavacat720]

Add a heatsink, it'll work, stick it on with an silicone thermal paste that's also an adhesive

[@ЕркебуланКурмашев-щ7л]

Это было не вольт а ампер

[@luizfernandolessa1889]

Excelente.🇧🇷

[@hitmanyt2021]

Make a video on voltage adjuster please

[@gkcmgk]

eller dert gormesin arkadasim sagolasin

[@JoakoFM-xw4pc]

2:56 Hi, Zafer Yildiz. Thank you, very much for doing interesting video. Can you explain how to connect a Li-Ion 72V=40A BMS in a 36V-40A Li-Ion battery? I tell you, it is possible, since we do it here in Mayari, Holguín, Cuba. Thank you very much I see all your videos, they are jewels. It's been a pleasure. Joakin

[@Sergey.9999.]

Спасибо большое за информацию.

[@sergeyvasiliuk6425]

Thank you. May you show us how to adjust voltage on this module. Thx in advance

[@johnbauer9223]

I need the same information also please Mr Zafar, Thank You!

[@clausqp]

This is only relevant for Lithium (LiPo) batteries. But yes depending on the C-value of a battery you should charge the LiPo with different current so that it will not be charged to fast!

[@Хренсним-т9м]

Спасибо. Удобно будет "толкать" аккумуляторы в наручных часах и блютуз наушниках.👍

[@ZAFERYILDIZ52]

Сделайте необходимые настройки для большинства батарей и используйте их годами.

[@abdullahkocoglu_1453]

Eline sağlık kardeşim peki daha düşük ma ile şarj etmek istersek kaçlık trimpot kullanmak lazım

[@khoaimo81]

That good 👍❤️🤪

[@thiagoether]

Nice video! How can I change the output voltage? I want to use it for a remote controller Flysky. I need 6v on output

[@Ruzgar_K_]

U can't. U should use voltage booster

[@Dalmen]

i think you need a Step Up Converter like the MT3608

[@Skare_]

Лучше бы не регулятор тока, а порог напряжение регулировать. Что бы заряжать действительно разные аккумуляторы.

[@daitedve1984]

Тогда какой смысл брать для этого явно неподходящую плату? Просто бери промышленный зарядник и заряжай чё хошь. Тут он просто поделился, как из говна сделать чуть более полезное говно.

[@uncnown_user]

И что? Ты будешь вливать 5 ампер в аккумулятор, который рассчитан максимум на 0,2 ампера?

[@martinger]

порог напряжения зашит в данную микросхему

[@bratecyo]

@@martinger в этом и проблема

[@martinger]

@@bratecyo почему же проблема? Для этой цели есть другие микросхемы. Причем, значительно эффективнее.

[@daro804]

Buen video - Pregunta: ¿Puedo cargar una batería de litio 1450 con el cargador TP4056? Gracias por su tiempo

[@joseluisesparzarebollar9858]

Genial Ing.

[@sasa-gl1vk]

I like Zafer Yildiz video. But I can't watch it because the music confused me. It's loads and noisy

[@petrpetrov8562]

Ползунок звука есть ?😊

[@شروحاتتقنيه-م8س]

How to edit voltage??

[@Faruk_Ah]

Hello sir, I am your regular visitor. How to charge a 3.80 volt lithium battery with this module, ie the cutout will be 4.35 volt.

[@brandondyzel7950]

Hi there. What is the max Amps you can adjust it to?

[@Ruzgar_K_]

1A

[@isaaarmandorh2803]

Buena idea para reducir el amperaje para cargar baterías que lo ameriten, pero aumenta el amperaje no es bueno porque el modulo con 1 amperio se calienta demasiado

[@TheRepairmobi]

Идея хорошая только не там автор ток заряда смотрит! или только настоящие мастера заметили? (у него на блоке питания лабораторном показывает не ток заряда, а ток по 5-вольтовой питающей линии)

[@rktur-pu5zo]

Дійсно, але погрішність невелика. На БЖ показує зарядний струм плюс струм власного вживання контролером заряду. Вважаю що він невеликий, тому їм можно нехтувати. Так що по більшому рахунку вимір коректний і відповідає дійсному струму заряду.

[@Septerrianin]

Это линейный стабилизатор. Так что 99% тока проходит через него до аккумулятора. Разница между 5В на входе и напряжении АКБ на выходе - рассеивается в виде тепла.

[@nuraliallabergenov9758]

Selamünaleyküm Zafer hoca çok güzel bahsetmiştim de yalnız ben sizden başka bir şey soracağım örneğin bir tane tp4056 kullanıp aynı anda 7-8 tane 18650 lityum batarya şarjlı paralel bağlayıp şarj edebilir miyiz Yani çıkış amperini 5amper yapabilir miyiz bunun için hangi komponentleri üzerinden değişmemiz gerekiyor veya aynısını yeniden yapmamız gerekirse nasıl yapabiliriz

[@mikebond6328]

The data sheet recommends charging no more than two cells with one tp4056 module.

[@tumertech4609]

How about adjusting the voltage output to charge 4v lead acid battery, can it be done?

[@GAMERBOY16469]

Merhaba ustam ben bu devre ile bir lityum pili şarj ettim pil 4.8 volta ulaşmasına rağmen mavi ışık yanmadı kırmızıda kaldı neden olabilir sizce

[@pareshbhai7917]

Very good

[@AntonioANT-z7c]

Ciao Zafer. Col tp 4056 posso caricare anche una litio 21700 ?

[@Qubnix]

Is possible to limit charging voltage, to stop charging for example on 4.15V?

[@johnbauer9223]

I need the same information also. Thank You!

[@ozelkuvvetler2820]

Merhabalar Zafer bey. Elimde trimpot bulunmadığı için kısa süreli kullanım amacıyla normal potansiyometre kullansam sakıncası olur mu acaba? Şimdiden teşekkürler.

[@mikebond6328]

A trimpot is a potentiometer.

[@ozelkuvvetler2820]

And this sentences are some bad because my English is some bad and i'm using translate of Google.

[@notmyname9062]

There are people that make videos showing nothing but just talking, and there are people trying to explain things in videos by playing pantomime. 🙄

[@SkapKovdor]

Согласен, видео ни о чём

[@fjcastaneda3264]

You're wrong. The pantomimes are an universal language. Otherwise you wouldn't understand this video.

[@low_hash]

Ахахах генит этого мира все же ясно, он припаял потенциометр и регулирует ток зарядки крутилкой, идиоты

[@deepaknanda1113]

@@fjcastaneda3264😂😂😂

[@redfields5070]

It means they can't speak English.

[@SatuSatu-j1g]

Cara buat power supply warna putih keren

[@shinjansardar9653]

can we do the same on output side

[@faikaykac]

Merhaba Zafer bey gerilimi düzenleyip lifepo4 pilleri şarj etme imkanı var mı?

[@candrasniper3404]

It will be a current limiter.

[@shahzadkhan-on3le]

Great

[@SidraKaleem-k6d]

I want that when the battery reaches full charge, the current doesn't cut off. The current should continue to flow at 4.2V. This is because the current cuts off at 4.2V, but the battery voltage drops to 4.15V or 4.1V, and after that, if the current continues for some time, the battery will be fully charged. Is there any method for this?

[@danielbas6068]

N'oublions pas d'ajouter une résistance "talon" de 1k dans le circuit sinon la durée de vie du 4056 sera vite abrégée si le potentiomètre se retrouve en résistance minimum !

[@erdemilmenoglu636]

Emeğine sağlık ustam bunu el fenerlerinin bataryalarına 18650 pil takarak tp4056 modülü ayarlayabilir miyiz

[@omerzambak7401]

zafer abi lifepo4 piller icin maksimum şarj gerilimi 3.7 volt olması gerektiğini duydum. bu devre üzerinde bu şekilde bir oynama yapabilir miyiz. yavaş yavaş bu pillerle karşılaşmaya başlıyoruz. tp4056 üzerinden bir çözüm bulursak gayet kullanışlı olur diye düşünüyorum.

[@user_best666]

4.2 а не 3.7

[@moosajaffar772]

Can you make a digital LED clock??

[@joakimjocka8022]

I have a 10000mah battery, I want to charge it using the tp4056 module, what resistor value can I put at the charge limit resistance?

[@olegi.4681]

Так и менять ничего не надо. На плате и так стоит резистор на максимальный ток заряда 1A.

[@ericklein5097]

When you say the charging current is one amp does that mean that the TP4056 module only changes the voltage (from 5.20'ish to 4.20) like a PWM solar controller and not like an MPPT that takes the energy input and converts it to a the battery charging voltage while (in the case of most MPPT's that reduce voltage) increasing the current?

[@Sinista123]

The Tp4056 is a very intelligent battery charger. Between a battery voltage of 3V and 4V it charges at 1A. If the battery voltage is lower than 3V it charges with very small Amps to get the battery to 3V If the battery is about 4V, it lowers the amps step by step until the battery is at about 4,2V It stops charging when the battery is full. If you change the value of the resistor R3, you can get the charging current between 3V and 4V from 1A down to 0,2A.

[@AntonioANT-z7c]

@@Sinista123 Ciao Sinista123. Ho delle 18650 da 700-800 mAh. Posso caricarle anch'esse col TP4056 1A? O me le incendia ? Grazie in anticipo per la tua attesa risposta. Antonio

[@Sinista123]

@@AntonioANT-z7c If it's only one single 3,7V 700mAh Lithium ion battery, then 1A is maybe a little to much. You should charge them with somewhere between 0,5 and 1 times the capacity of the battery. It's possible to modify the old micro USB version of the Tp4056. This version has a bigger R3 resistor. Replace the resistor R3 with a 2K Ohm resistor or try to find someone who does it for you. 4k Ohms is about 300mA charging 3k Ohms is about 400mA charging 2k Ohms is about 580mA charging 1.66k Ohm is about 690mA charging 1.5k Ohm is about 780mA charging

[@AntonioANT-z7c]

@@Sinista123 Ciao Sinista123. Grazie davvero di cuore. Le resistenze di cui parli, oltre ai K Ohm, hanno anche una sigla per le loro dimensioni? Vorrei comprarle evitando di sbagliare... Buona giornata.

[@Sinista123]

@@AntonioANT-z7c You can use standard ¼W resistors or smaller. It doesn't need to be perfect. I would use 2x standard 1K Ohm resistors, put them next to each other and twist the ends of one side together. Then use both ends on the other side and replace the resistor R3 on the micro USB version of the Tp4056 with that. I would not get the USB-C version of the Tp4056. Because the resistors on the USB-C version are so small, it's almost impossible to replace them with something else. If you want to use USB-C, you can get a USB trigger board and set it to 5V and then connect it to the 5V input of the Tp4056. Then it should also work with every modern USB-C charger.

[@sercanbahrioglu]

lipoyu 1a ile şarj etse ne olcak? yada yani 0.2a ile optimum şarj oluyor ise batarya, bunu nasıl bileceğiz? elimdeki bataryanın kaç a ile şarj olacağını nasıl bileceğim?

[@prasaadvelaga]

Please make a cell phone charger with auto cut off facility. Thank you

[@mikebond6328]

That’s what the tp4056 does.

[@SuleymanBulut-pm6ev]

Hocam merhabalar. Elimde tp4056 modülü var bu modüle 18650 pil bağlıyorum çıkışından olması gerektiği gibi 5 volt veriyor. Bana 6.5 volt bir çıkış lazım mutlaka voltaj yükseltici devre kullanmam lazım mıdır yoksa bu devre üzerinde bir değişiklik yaparak çıkış voltajını 6.5 volta ayarlayabilir miyim?

[@Mousa-bn2hd]

Hi can you explain why if we charging the battery in tp4056 with load on it will damage the tp4056 module .. and how we can charge the battery while the load is on is there any solution to charge and using load together Best regards .... mousa Alabbasi

[@LiliaHdmi]

Sir! Nice video. Can you please help me to fix my Bosch bms Li5s4l01 board for bosch vacuum cleaner 14.4v. Apparently there is issue with a circuit. I have taken picture for it. Can you please help me find a replacement one. How can I contact you for help!

[@امیرحسینخلیلی-ي4ث]

Good ❤

[@ON3MR]

comment modifier ma securité de decharge ??? moi je veux deconnecter les consomateurs quand la batterie descent a 3V

[@Thealexpj1]

Обычно при таком токе 1а, чип дико греется начинает и ток начинает падать. Но подсоединил он резистор странно у меня как положено в стоке схемы

[@vinnica404]

За звичай, на вхід даємо від 4,4-4,6 Вольт, температура дуууже знижується. Перевірено роками 🖖

[@Thealexpj1]

Окэй умняшка, как нибудь зазвичаю😊...если ты мне говна не желаешь...то вам лай и подписка

[@مصطفيسعد-ش3و3ت]

Can't soldering in right side on R3 ?left side soldering good but the right isn't

[@ИВАНИВАНОВ-в1з1р]

Привет друг. Собери схему, минимально используя детали для управления симистром BTA41-600 что бы затвор управлялся микроконтроллером ардуино

[@сашататар-с9у]

для чего это нужно

[@ДмитрийФамилия-я6т]

Оптосимистор поставь, снаберную цепь и цепь питания управляющего электрода

[@muongnguyen]

xin đuong link mua đồng hồ đo

[@Зубарев_Александр]

Не заряжай дутый аккум !!!!

[@viktortupikin7739]

Измерять зарядный ток нужно не во входной цепи, а цепи батареи.

[@КРЫШАМИРА-к4е]

ток одинаковый, что там, что там...

[@Septerrianin]

Это линейный стабилизатор, а не импульсный. Поэтому ток течёт сквозняком через батарейку, кроме пары-тройки миллиампер на собственные нужды микросхемы и диоды.

[@arifgules700]

Zafer ustam 8610 bağlantılarını yaptım ama ses gelmiyor neden olabilir

[@egorl1907]

Вопрос к автору видео... А если подстроечник в ноль закрутить по нечайке.... Микруха выдержит? Думаю, нет.

[@ВладимирШабалин-и2г]

значит, надо впаять ограничительный резистор

[@hasantamer9199]

teşekkürler