Bits of wood Workshop

Пікірлер

@Maggiewuvsrufus 21 күн бұрын

I’m totally stealing the sign idea brother thanks. Liked and subscribed for payment

@powerhouseexotics 22 күн бұрын

I was wondering why youd need so many containment measures then i remembered it was a husky

@rod1148 Ай бұрын

There has to be a safer way to do a round-over on router table

@aranxamorales2468 Ай бұрын

Would you make a video of how to make some post for that fence

@swishair Ай бұрын

Awesome coasters.

@andreysuday2559 Ай бұрын

👏👏👏👍👍👍👍👍

@patriciasoares9204 Ай бұрын

Sensacional!😊🎉🌟🤗.

@engageesmservicenow9373 Ай бұрын

Please send the drawing (as a pdf) of the outline of the car

@davidtaylor7137 Ай бұрын

Hopefully, you can make your bed better than you can upholster.

@Tovii2022 2 ай бұрын

Husky would have the last words. Lol.

@fyerdawg2247 2 ай бұрын

Wouldn't hold my Border Collie though. He tears the fencing apart. Would have to get the lowest gauge chain link fencing available and still may not stop him. Local stores only carry 9 gauge but he tears a hole in it and climbs out.

@aniballeiria6511 3 ай бұрын

👍

@livecalm2246 3 ай бұрын

Is it chew proof lol

@thepatrioticmistersnevets9850 3 ай бұрын

Great video! However, the correct tool for part of this task is wire cutters instead of tin snips. Using tin snips in this manner is akin to using your mother's pinking shears to cut paper.

@RaydarCreative 4 ай бұрын

Very cool. HOWEVER i really hope no one uses the router like he is doing in the video. Having your fingers so close with a small piece of wood is extremely dangerous

@christineshotton824 5 ай бұрын

Cattle panels+/or similar flat welded fencing laid out on the ground and wired together, cover with sand, pea gravel, dirt, mulch for different areas of the kennel depending on activity and helps keep dog clean and happy. There are obviously different sizes of grids and panels HxWx so make sure it would be impossible for your dog to squirm through the grids. I add 2ft high x 1/4 inch weld wire because of 🐍 RATTLESNAKES.😮

@freewoodencrosses 5 ай бұрын

I want to make 200, this way is too slow.... I need speed

@willieisadore5246 5 ай бұрын

I got a question. How do you know where to mark the mitered corners if it has a rabbit for the bottom? Would you have to take that much off of your miter so the side would sit in the rabbit?

@DC-cv8jg 5 ай бұрын

Our dog actually pulls on the wire with his teeth until the hole is big enough to get out

@rafaelcueva6786 5 ай бұрын

Great work!

@HUNT-DOG 6 ай бұрын

Bravo. Design, editing, all of it

@jamesmurphy2837 6 ай бұрын

Do you sell build plans

@scottromero2091 6 ай бұрын

Good Job😃

@scottromero2091 6 ай бұрын

Good Video. I needed to see this.

@gpdoyon 7 ай бұрын

Great job!

@thembikunene5175 7 ай бұрын

You had me at "...obscene amount of staples..." Great job, I'll be doing this soon - God forbid that the "poor sod that needs to remove the screws... " doesn't actually end up being me again!!!

@andrenascimento7680 7 ай бұрын

Muito bom

@andreatrepasburgess8520 7 ай бұрын

You made it actually look like I could achieve this .. was the removal of staples the hardest part or getting the new material tight enough around the pinched corners ? Came Out great

@hunnybunnyssunshineliving5155 7 ай бұрын

😂😂👏🏽👏🏽 BEST ONE FOR SURE 🙌🏽🌟THANKS

@emilyambrose6852 7 ай бұрын

What a sloppy job!!

@nmfam 7 ай бұрын

Great job

@tarastevens3866 7 ай бұрын

SO ❤ this video!!! Thank you for the music selection, visuals, and captions. My favorite part was the extra staples. It also confirms that this DIY project is not for me😅

@roberthernandez7531 8 ай бұрын

What kind of foam it thar

@Offy-official-real 8 ай бұрын

Nice. What's the minimum thickness I can go with a coaster?

@hamiltonbernardes6869 9 ай бұрын

Has a PDF of the drawing

@gsp911 3 ай бұрын

Is it one you want to share with the rest of us?

@brw3079 2 ай бұрын

I would really like to have one too.

@michaelmattia932 9 ай бұрын

Can I get thee pattern for the parts?

@vitocantore8366 9 ай бұрын

Bravissimo maestro 🎉😊

@tamara8908 9 ай бұрын

I've watched several videos trying to muster up the courage to do this. Yours is the best! Very straight forward and simple to do. I loved how you use the foam is a template for the fabrics.

@BarjoNurfajar 9 ай бұрын

Salam dari q di indonesia ya kaka❤

@toddpiechowski 9 ай бұрын

don't suppose you have dimensions?

@natalieelisabeth5767 9 ай бұрын

This was helpful and fun to watch at the same time! Great video, thanks!

@justyb2209 10 ай бұрын

For a second I thought the thumb nail was showing a table. That would be beautiful.

@stevel8980 10 ай бұрын

What size wheels and what size Forstner bit for wheel wells? Thanks

@renam3456 11 ай бұрын

I love the sound affects in the beginning of this video! 👍😂 And I Really liked the fact the video was short and sweet, aka to the point! When I Reupholstered my dining room chairs, I found that a stapler remover was the easiest way to remove the staples! Can get a stapler remover at any office supply store, or can do like I did, and just go to the dollar store and get 2 for a $1.26!

@timlarson7228 11 ай бұрын

Oh my goodness! I just saw your branding tool ! Great idea. Not sure how I could make something similar but id love to try. Thank you for sharing your excellent tutorial.