Pauls Workshop

Пікірлер

@csutteszdnb 8 сағат бұрын

Hahaha wow

@577buttfan 9 сағат бұрын

I think you contaminated the test by not rinsing the tool off with distilled water first. Your tool may be faulty

@tennouheikabannzai 5 күн бұрын

It's the worst and most costly method.

@larryblackmon7105 6 күн бұрын

Bro....... go back to your office job and don't ever do a"how to video" again.. you remind me of a 12yr old child helping his dad and even the dad don't know... it's sad really

@samshandyify 8 күн бұрын

thank you so much, best advice and very specific, i would have never guest that would be the problem. I was being charged $220 just to tell me what it possibly can be. Problem solved. again THANK YOU

@tarekghadieh1416 9 күн бұрын

I got an HK-40 cartridge for Uberhaus fixtures, much like the one you have. It produced water hammer anytime a fixture opened or closed in the house. I purchased another one thinking the first one was defective, but it makes the same noise when I shake it (didn’t install it yet). Any suggestions or recommendations to get rid of the water hammer?

@DCDC2012 2 күн бұрын

I had the exact same issue as this video series but with an old delta. The cartridge started knocking after I turned off the main shutoff without draining water. When I went to flush the toilet the air trapped inside forced out, where I suspect is where the cartridge/cartridge seals were dislodged or broken. When turning on the faucet or when other areas of water is running it knocks. Got a new knockoff catridge online and when you shake it also knocks, but I think the seals and gaskets inside the device stops the flow of water better, which is what's pushing the bearing inside to knock. When installed it doesn't knock so you just have to try it.

@katydidnt3906 10 күн бұрын

Dodge puts a engine cover on these V6 Pentastar engines in other vehicle models, but not the Promaster. Class action lawsuit is what needs to happen.

@BonesBonesBonesBonesBones 11 күн бұрын

Cool thanks

@jeffjeff9795 14 күн бұрын

I have a coleman 285 lantern and same happens when it's low on fuel (less than 1/4 of the tank). I just top up with more petrol.

@markk3948 14 күн бұрын

Cool tool. Too bad you shot all that saw dust at the window tho lol

@JinxedJax 19 күн бұрын

Doesn't enamel paint yellow and dull quicker than an acrylic latex?

@sharonfrommann6516 20 күн бұрын

Thank you so much for showing this

@Mattie_Ice 22 күн бұрын

Hey, did you stain these floors yourself? They look great. If so, how did you do it?

@Davidlovesmusic311 23 күн бұрын

But if you want to that blade lasted me a year working 5-6 days a week cut perfects and I've used every blade there is

@joshualevy4784 24 күн бұрын

Thought of getting this (already invested well into m12), but Dewalt 4 1/2” fits in the packout drawer.

@31acruz 29 күн бұрын

There's gotta be an easier way. Maybe they sell a plexiglass cutter.

@oceanic8424 Ай бұрын

Can’t beat a table saw, or circular saw with a carbide saw blade for clean cuts on acrylic (plexiglass), or polycarbonate (lexan).

@lvl5Longbowman Ай бұрын

Been sitting in my shop for nearly 3 years. Just learned to use it.

@jayb2344 Ай бұрын

So did this the other day and got way too many fractures than I wanted. Couldn’t find my rotatory so I used a hot knife

@MegaMeco2 Ай бұрын

go with Pearl P3 or P4 blade , you won’t regret it , tried dewalt , rubi , rigid and none compare .

@joeybrazda364 Ай бұрын

Can anyone tell me how to sharpen these wheels when the wheel smooths out after using it for a bit

@johnnyk617 Ай бұрын

Perfect video short and simple thank you

@0FlightlessBird0 Ай бұрын

If you look at the bottom of the windshield there’s often a gap there and water runs under it straight onto the engine. Also the drains in the little water catchments underneath the windshield wipers can get clogged.

@randya103 Ай бұрын

Can you be more vague next time?

@Matthew-ju1du Ай бұрын

That ain’t stopping my grandma

@Fefitoly Ай бұрын

What is that drill called??

@Particle_Accelerator_Repairman Ай бұрын

Wait, one little screw...to hold someone who is going down for the count and grabs that rail on the way...soilid? 😂

@jbollhoefer26 Ай бұрын

Not a narrow crown stapler

@saeedalqahtani926 Ай бұрын

Thank you for this teaching video❤

@Apathy_is_the_worst_sin Ай бұрын

I’d try searching on how to fix CO2 canister leaks and oxygen tank leaks. There should be forums with people talking about these. Edit: you should contact support if you can.

Ай бұрын

Why not just dot and dab?

@Rmer716 Ай бұрын

Nice! You got a new tool. Thanks for sharing that with us

@GenXGamerGirl_ Ай бұрын

Thanks! Getting ready to replace decking with Trex. It's not a large deck, so I plan to DIY.

@samaelmartinus3273 Ай бұрын

Arizona here. I still ripped off

@jhutfre4855 Ай бұрын

this is phenomenal, thanks a lot!

@astrix90333 Ай бұрын

To put in pledge 🌏🌞⚡️🎋4G59 📖249. Plaster-Planētas P. 😇😇😇🪖🎩⛑️🤗🕋🥸

@samairasahai 2 ай бұрын

Literally been searching for a the charger for like a week around my house, this was a lifesaver

@oscarcastillo6779 2 ай бұрын

Thanks I'm going to try that tomorrow, but my my car doesn't turn on either,u think that's the problem too,The Fuse? I hope it is

@toast_2375 2 ай бұрын

imma be so fr i did not know they had filters

@alexzbarazky3038 2 ай бұрын

Have you checked wheel balance? I've had a customer drive through clay. That clay stuck to the wheels and got them off balance. Maybe something was stuck to your wheel or you lost a wheel weight.

@danielpainter718 2 ай бұрын

need warmed up the.generator listen.the.sound first.before fire

@lbaker3602001 2 ай бұрын

Almost bought one, could not find a blade to fit it @ Home Depot. Didn't want to invest in the M12 battery line.

@joshuawalkermusician 2 ай бұрын

This is a neat concept. I'll definitely try to recall this next time I get in touch with one of my construction friends.

@jaredkaye3669 2 ай бұрын

Ahh! The rear tire is hard to put a plug in. I had to pull out and use the debrider because... I can only apply 90 pounds of force by squeezing the tire between my left foot and two hands acting like Thing wiggling the plug in over 60 seconds; just enough!

@Dpe_Ice24 2 ай бұрын

I want too but this seems shotty asf. 😂 I might get plumbers to install posi temp valves 🤦🏾‍♂️

@roswel7845 2 ай бұрын

I’m in the process of covering up some of my damage similar to yours but a much darker stain

@joshtucker4903 2 ай бұрын

That looks horrible

@HonorioSoto 2 ай бұрын

The issue is that they are sent out without motor covers and when the water drips down the center of the windshield the water rolls down to cylinder one and rusts it up.

@alexzbarazky3038 2 ай бұрын

Exactly

@triblackant 2 ай бұрын

Very good job dad. Used your method but I used two small flat blade screwdrivers and needed to work them along by lifting with the following driver while scooting the front driver along. Made a small mark at initial pry area that I can live with.

@genmarrie 2 ай бұрын

This should be labelled “looking at a blade I use”. Very informative I must say!

Ең жақсы KZbin

Пікірлер