What kind of clutch and flywheel did you use ? I’m not sure how to shop for my cd009 transmission in my sr20.
@matttafakt2 күн бұрын
The control joint might appear that way because moisture may be coming up through it from under the slab . I'd never install this stuff in a garage where you do work or drive over it. Try steering your tires on this and watch it tear off the floor over time. Bare cement or Epoxy floors is the way to go in a garage like you had before. If you're worried about acoustics .. go buy some rockwool from Home Depot, cover it fabric and attach it to the walls. If you want comfort while working on the floor , buy an area rug or use some old carpet.
@matttafakt2 күн бұрын
I always go with custom swaybars with splined adjustable end links and custom steering linkage in cases like this
@chuckblankenship51227 күн бұрын
Hey man did you stop building? No videos In a year! Hopefully you are all good.
@matthewrodas873012 күн бұрын
did exactly this and my calipers cracked when applying clear coat
@troyself87119 күн бұрын
Removing is almost impossible
@beano934320 күн бұрын
2:54 that aint tight, you should see this engine stuffed into a Datsun 120Y
@Boris94221 күн бұрын
Looking at buying this exact welder and generator setup. Thanks guys
@snipermex1326 күн бұрын
How hard is to do the swap, I currently have the v6 on my hardbody but I wanna swap to a fuel injected
@mr.Lumpy380326 күн бұрын
If you were confident enough to put carpet in your garage. Then that tells me that you don't do any work in your garage, and it's just for show.
@Inner_Sanctum26 күн бұрын
@@mr.Lumpy3803 lol you’re more then welcome to check out all the videos of me working in my garage with this carpet. These videos include welding, grinding, engine swaps and etc. I just have enough foresight to make sure I protect it if I’m doing something that could mess it up. Your lack of due diligence is not a trait I regularly practice.
@klinkster1915 күн бұрын
Hush!
@Jason-xe6rq14 күн бұрын
Who gives a damn?!
@coreyblizard62126 күн бұрын
This is an awesome video, thank you. Currently starting my 4 link. My dif is still attached with leaf spring and stock height. Should I lower the truck prior to starting this project or does it matter? Plan is to airbag truck. The thought process is with it attached to the leaf springs I would have a my position solid (front/back/left/right) and after Installing top links, I could remove the leafs and then install the bottom two. Also just to verify, the top rods and bottom rods should all be parallel to the ground? I see a lot of four links with a downward slope on the top two. Thank you in advance
@DuncanZoe-l4r26 күн бұрын
Brown Kevin Thomas Eric Jones Melissa
@devoncanada227 күн бұрын
I know this video is old but I just bought the same line kit but for my s13, the block side adapters came with a crush washer on one side, and on o ring on the other. Do I use oring for the block? I know AN is supposed to seal by itself so that’s why I’m confused on why they included both. Thanks!
@batvon3927 күн бұрын
This is the most helpful caliper painting video I've seen. Answered a lot of questions
@rickwhitfield7617Ай бұрын
Nice improvements for the spend! I am getting ready to put some Titan 1" spacers on my Frontier P4X myself. Did you locktite the hub bolts?
@100superkАй бұрын
I cant find where to buy the Domino holographic flakes, can someone help??
@vigilance6806Ай бұрын
Do you need to strip the original paint or just scuff it after degreasing?
@reygomez323Ай бұрын
Is there a way for me to figure out what I need, how about the new El 31 MP which 140 amp welder. I just want to get a generator a good one may be a Honda to run it with no problems I just want to know if there are an equation to figure that out thank you good video
@PonkyKongАй бұрын
80% maximum draw at peak with 5% maximum total harmonic distortion from your inverter. But the bigger your generator the better.
@gabriels3106Ай бұрын
What did the misfire problem end up being, if the timing was proper?
@Inner_SanctumАй бұрын
@@gabriels3106 injector o-ring tore during installation on cylinder 4.
@gabriels3106Ай бұрын
@@Inner_Sanctum Legend! Thanks for the quick reply.
@timcollins8812Ай бұрын
I would love to know how it doesn’t rub. 1.5 spacer rubs on a 2022 pro 4 with lift. Had to remove mud flaps
@H00K-KINGАй бұрын
How did you figure out that you need a 450 lb spring rate? I always see people with way higher spring rates in their drift cars. Most are 18kg front and 10kg rear
@zephdulalia2481Ай бұрын
What are your spring rates?
@jamescason7783Ай бұрын
Did you ever use it with one of the 220 welders? I’d love to know how that went. I got the same one to run a welder. Did fine but I’m definitely questioning if it could handle to 220’s
@adamodare87Ай бұрын
Can you please provide height from highest point of sump to top of engine? And crank centerline from base
@MalBeats101Ай бұрын
What rims?
@marcpender7120Ай бұрын
Brilliant review. What's it like with welder sparks ?
@cantgapthis350fАй бұрын
i need those tires !!🔥 what kind are they
@st4t3kАй бұрын
Hi, I'm searching stronger and cheap gearbox for my worn gearbox in my SR20det (about 320hp). Friend of mine told that somehow is possible to use this d21 gearbox. And do you have any knowlege about it? I see that the gearbox from d21 is shorter, but the front should fit well with SR20 gearbox bell housing. But how about rear end, or it's reallly just swap front section and put to sr20det housing? Thanks in advance for any advise :)
@InquisitiveMind876Ай бұрын
May have missed it. What happened to the wide body fenders?
@InquisitiveMind876Ай бұрын
Startng this series from scratch n i DO NOT like ur videos. They are convincing me more and more to pull the trigger on the project 😭..... Oh well, onto Ep 4.1 lol 😅
@InquisitiveMind876Ай бұрын
Not me seeign a hardbod for sale and ending up here
@kirkmaiden2705Ай бұрын
Thank you 🙏
@oisteenloken2131Ай бұрын
Very detailed video. Thank you sir
@larrywilliams6774Ай бұрын
Would this work with the Hobart 140 mig welder?
@24BLUEELMOАй бұрын
Where do you buy your welding gas in San Antonio?
@brandon_buildsDIYАй бұрын
Just came across your channel and I think I’ve found a gem.
@indyfernandez90732 ай бұрын
Hey bro that piece that connects the seat to the slider did it come with the seat or the slider
@Jonathan-qz9kd2 ай бұрын
Just doing the same process to my brembos for my mini! You recon I should use your process over the calliper paint?
@gammagonad16572 ай бұрын
It does look good, I would like to do both, but for my use case(towing a 14,000 lb. 5th wheel) it would be weakening the axes/studs and maybe both?? Now the 1.5” leveling kit I could get behind. Looks better for sure
@Inner_Sanctum2 ай бұрын
@@gammagonad1657 I agree 100%. If you’re towing that kind of weight, it’s just not worth the risk.
@Bando-fx4mf2 ай бұрын
I’m in same boat. Where do you live, need to drop the car off to you. Need same dash service done.💯
@Inner_Sanctum2 ай бұрын
@@Bando-fx4mf I live about 20 miles north of San Antonio.
@4077661466jp2 ай бұрын
Vq35 swap vs sr20det swap , wont mention sr20vet but cost vs hp and aftermarket support id say Sr is a way easier and performance potential bang for the buck !
@Inner_Sanctum2 ай бұрын
@@4077661466jp I’m not really sure. I have an SR in my white truck and still think the VQ is a better choice overall.
@4077661466jp2 ай бұрын
Put v8 in that G that be nasty
@Inner_Sanctum2 ай бұрын
@@4077661466jp I’m putting a VK56 in my G sedan. Haha
@pnwchris20002 ай бұрын
This may be a noob question but I’m not very informed when it comes to suspension stuff, I’m more of a paint and engine kind of guy. My question is, if I were do this with the Ford 8.8 I bought for my S10 but I wanted air suspension instead of using coilovers, would the entire link process stay the same and the coilover mounts be a very similar process/area and I would just be bolting in the bags instead? Does anything in the system need to change if you were to use airbags instead? From first impressions it looks like it wouldn’t change anything but I’m very very new to all this none leaf spring suspension stuff.
@Factors_808Ай бұрын
It would be the same. You could use a mustang 8.8 with the upper mounts already built in, but the explorer rear has bigger axle tubes and 31 spline axles. You could change the mustang axles though
@regis65442 ай бұрын
If im going to make it on my tdi vacuum actuator, i dont need relieve hole? Because tha vacuum from vacuum pump will suck excess air from controller?
@OddFarmGarage2 ай бұрын
WOW the dedicated videos for highlighting differences really makes it a lot easier to find the information needed! Thank you! Cheers from Sweden
@OddFarmGarage2 ай бұрын
Wow! Really informative and great video! ik im late to watch it but great info for future CA18 D21/ KA24 200SX :))
@calebdewer10152 ай бұрын
Should’ve VG swapped it if yours didn’t already have a VG
@NissanNut742 ай бұрын
Is this kit still available? Do you have any details on it? Looks like a spacer?
@toddkirkland86552 ай бұрын
What motor do yo advise for my 96 hardbody I want porformance and power but a daily
@sr20dett10002 ай бұрын
Oops. I put the clear then put it in the oven. I didn't know I needed to put it in the oven then do the clear.