Hillside Acres

Пікірлер

@MaxStrasser-o3s 10 сағат бұрын

Great information. Watched, checked my L3400 and guess what - 4 quarts later I'm now good to go. That's a lot cheaper then a rebuild.

@wingmasterjimmy6724 2 күн бұрын

Good advice,my 1994 l3300 has 3500k on it -only recently bought it so will be checking it out asap.,what size of AG tyres are you running?

@HillsideAcres 2 күн бұрын

11.2 - 24

@newslavecity8311 3 күн бұрын

its also not important to note there is also another bolt for draining the fluid. i drain my fluid once every year and replace it with new fluid. i had a 9540 drained nasty gunky oil ever since then i replace the fluid completely every year. if your fluid comes out clean then dont drain it all but if its black or dirty drain it all. also remember oil breaks down over time due to oxidation when its exposed to heat and movement. even if ur oil looks new it may not be good due to it being old oil thats broken down over time. oil sealed in its original container stays shelf stable for about 5 years up to 8 or higher for synthetic oils. but once its opened and exposed to oxygen, heat, pressure and movement. even you replace the oil in ur engine and never use it, it can still degrade in as soon as 6 months, but about a year is more realistic.

@bryanmontgomery4050 5 күн бұрын

My old one gets 50% Lucas so it doesn’t leak as fast! Haha

@TheCC89 14 күн бұрын

Use an Allen key to check fluid levels on stuff like this. Take the short end and put it in the check hole, then hold the longer end up flat or level. Then pull it out and check the wet fluid level mark on the allen wrench. This doesn't tell you how much to add, but does give you an idea of how low it is.

@HillsideAcres 13 күн бұрын

I prefer the way it’s designed to be checked. Showing oil dosent mean filled to spec

@TheCC89 13 күн бұрын

@HillsideAcres That is exactly how it is supposed to be checked. If you use the Allen key method, just like you would with a differential on any equipment or vehicle... And the fluid level is flush with the top of the fill level drain check hole, like the Allen key would show, then you know for certain if it is full, slightly low or really low. This is how you check these types of port hole fluid levels without guessing and dumping oil in to see if it comes out... Not saying your method is wrong, but there is a much easier way to know without guessing. Also, just because the manufacturer says a service isn't due till this many hours, doesn't mean checking or doing the service earlier isn't a good idea. I personally like to double up on my break in service schedule on new equipment because that is the most important service time. On my new L3901, I did a full service at the 50hr, 100hr and 200hr intervals. Then again at 400 hrs, because why not. A few extra hundred to protect a $30k machine is well worth the extra money spent. I just did my 800 hr full service.

@hokiedokie 20 күн бұрын

Hows the transmission holding up?

@angusblack9900 22 күн бұрын

Make sure your front axel is 5:32 level.on Concrete is good but if on dirt it might give you different results

@sealevel1919 25 күн бұрын

Update

@scotboudria4544 Ай бұрын

Where did you park to start the ride

@davidthegood Ай бұрын

That was very satisfying to watch.

@jameskennerly9748 Ай бұрын

Thank you Sir 😊

@hiatusranchofidaho Ай бұрын

What if you have dogs and horses that use the pond

@peterwill3699 Ай бұрын

My L2650 constantly gets water in the axel through the knuckel design.The udt seems very light to lubricate those big gears.

@HillsideAcres Ай бұрын

Can switch to gear oil

@josecornejo9850 Ай бұрын

I wander if you can tell me where you got all parts for b7000 kubota front diff

@HillsideAcres Ай бұрын

I don’t have any parts for kubota b7000

@gryphaeon Ай бұрын

Kubota is seriously dropping the ball. There are too many other options available, at lower prices, for them to be letting their quality slip like this. I bought my L2501 brand new from a dealer and I asked if I needed to do anything upon receipt of it and was told "no, it's good to go, just like a brand new car, but read the manual and do the services and checks on time.". I shouldn't have listened. I lost several nuts and bolts because nothing was tightened beyond hand tight when they assembled it, including a hydraulic line that leaked about a gallon and a half of fluid before I spotted it, and none of it had been greased. When I contacted the dealer about it, he said it's the owners responsibility to check all that stuff. 😡

@HillsideAcres Ай бұрын

All of that would be on the dealer not kubota. Dealer is responsible for final assembly and pre delivery inspection.

@gryphaeon Ай бұрын

@@HillsideAcres it's my understanding that kubota is ultimately responsible for the dealerships using their name. Since they're part of the revenue stream and have done nothing to correct the issue either, i hold them accountable. I'm not the only person to have trouble with this dealership, their lead mechanic left and started his own business working on them because kubota won't do shit about it, and he's making a killing fixing the shit the dealership is butchering.

@HillsideAcres Ай бұрын

@ that’s pretty much the sad reality of any dealership, quality control has gone to crap across the board. If you think you’d be better off with a Korean tractor give it a shot. Some people get decent luck some people constantly have a tractor down waiting months for parts

@72151 Ай бұрын

If you don’t have one of these EU2200’s, you should rethink your decision. They are the most efficient and best quality gas generators built. Perfect sine wave power.

@HillsideAcres Ай бұрын

I think it’s pretty clear I have one lol

@eddiewiercioch777 Ай бұрын

Great video doing mine this week. You will have to elaborate on the fuel vent when you do that. TY.

@Alexislaughs Ай бұрын

That wrench drawer is awesome

@AXNJXN1 2 ай бұрын

Really suggest to modernize that puppy Bud. grab a magnetic oil dipstick, which comes with a drain/fill funnel and grab an oil siphon tube. Save your back a bit. Cheers.

@HillsideAcres 2 ай бұрын

Have it

@texas4325 2 ай бұрын

I have a f250 6.8 gas solid truck. What are you driving now sir?

@HillsideAcres 2 ай бұрын

Went to a 2022 Duramax. Has been great so far no problems

@andyd5492 2 ай бұрын

I thought one of the mods he was going to talk about was putting a Motorcraft filter on the Honda. 😂

@deanshepherd612 2 ай бұрын

Doing my 400 hour maint. on my Kubota L3302 now. Just added this to my list after seeing the video. Thanks for the heads up.

@JuniperDustFarmBoy 3 ай бұрын

Approaching the 800 hour mark and getting ready to do some maintenance. Not sure where things are at. Wish I would have seen this sooner. Cross your fingers for me.

@Splintermill 3 ай бұрын

Can’t go wrong keeping a close eye on your fluids. My truck isn’t always polished up, but you can bet the bank all of my fluids and filters are on point! Bought my b2601 brand new and there wasn’t a fluid on the machine that was right when I got it. The dealer I bought it from also needs to get there techs a new torque wrench. Ended up going over every bolt on the tractor after two chassis bolts and a rear wheel lug fell off just mowing with the belly mower. Ridiculous quality control. Fact is, we all make huge investments in these machines, take a few minutes and keep thing tight and topped off and you’ll get several thousand hours out of these tractors.

@shelleykrier7417 3 ай бұрын

Yes they can throw a lot of debris but I'm cautious and try to pick up as much junk before starting. I always wear high heavy boots with eye and ear protection. I love the machine and it has been well worth buying it. Another thing to remember with this is to always use good body mechanics with all the pushing pulling and twisting motions you put your body through. This includes shoulders.

@HillsideAcres 3 ай бұрын

👍

@StephenNovotny-y6x 3 ай бұрын

Thank you very much!

@suefox6164 3 ай бұрын

Thanks! I've learned a lot.

@tedbastwock3810 4 ай бұрын

This is useful to see in action, I've been thinking of a similar setup. The pto hp of that tractor is lower than the hp required to get the full juice from the generator. And I've been wondering if I can put an oversized generator on my pto with the foreknowledge that I wont get the full kw out of it. The reason is tractor pto hp takes a lot of different values between tractors, but the pto generators are only a few hp values. Thanks for sharing, was helpful.

@randymclean5039 4 ай бұрын

Hello I'm in Durham and bale with a m7040 on hills. How does the dm1024 cut thick first cut. Second cut should not be a problem. Does 1st cut ever jam up in the curtain? Can't continue using a haybine. Too wet these days.

@HillsideAcres 4 ай бұрын

It will cut as fast as you can handle driving. Feel free to come check it out in the spring for first cut

@TommyOmallet 4 ай бұрын

I’m going to drain and refill mine with super udt2. Dealer was very little help. It smells like gear oil, not udt2. I suspect it is gear oil.

@HillsideAcres 4 ай бұрын

Gear oil is fine

@LostCaper 4 ай бұрын

kubota better smarten up or they will be loosing alot of business. I bought a L2502 and had alot of small trouble.

@LostCaper 4 ай бұрын

I subscribed. Great detail and clarification. You do a great job. I just sold my L4740 and bought a L2502.

@LostCaper 4 ай бұрын

great clarification. I am sitting here wondering what side was the transmission filter on. Thanks great video.

@VideoByPatrick 4 ай бұрын

BX2380 here, walked by it this AM and wondered what that front axle cap was for......

@HillsideAcres 4 ай бұрын

Can’t hurt to check it out!

@jackjones9611 4 ай бұрын

Is the microphone in your nostril?

@HillsideAcres 4 ай бұрын

Yes it is

@rodneyjones675 4 ай бұрын

Mine was 2 qts. Low

@Owl4909 4 ай бұрын

thanks

@PaulAndrewKennedy 5 ай бұрын

just picked up my 24 f350, thanks for the content.....

@jetmech77 5 ай бұрын

Thanks, I will check mine. Where did you get your tool box foam??

@HillsideAcres 5 ай бұрын

Box and tools came from Home Depot and a company called foam fit tools makes the drawer organizers

@jetmech77 5 ай бұрын

@@HillsideAcres Thank you, I will take a look

@danielthomason5685 5 ай бұрын

Your hose in wrong side of valve

@HillsideAcres 5 ай бұрын

How is it wrong

@jomckeag4482 5 ай бұрын

Please review - the 14 mm is the CHECK, not the fill

@HillsideAcres 5 ай бұрын

It would be both

@mikestillshreddin7636 5 ай бұрын

Looks like your freezing your ass off... tell me how it all works out, im going back in the house , later

@philipvacanti577 5 ай бұрын

I would have liked to hear more comments, and less time of you mowing.

@HillsideAcres 5 ай бұрын

Thanks for watching

@theyouthfulbodypro3985 5 ай бұрын

What’s the horsepower of your other tractor that you use? My tractor has 25 hp and I’m not sure if that one will work with it. Love to hear what you use with your other tractor.

@HillsideAcres 5 ай бұрын

One is 25hp and the other 75, 25 does fine with anything that isn’t firewood

@theyouthfulbodypro3985 5 ай бұрын

@@HillsideAcres how about being able to pick it up and move it? I know there is a considerable weight to that chipper.

@HillsideAcres 5 ай бұрын

@@theyouthfulbodypro3985 I think it is about 1000lbs

@thebestofbelltowneasthampt6679 3 ай бұрын

So with you running those 6 and 8” through that chipper… What is your understanding of the horsepower at the PTO from your tractor?

@HillsideAcres 3 ай бұрын

@@thebestofbelltowneasthampt6679 it’s 64 hp at pto but I would typically run in 540 e which runs the pto at 540 at about 1700 engine rpm to same fuel. On the hydraulic chipper you can slow the in feed rate to make up for horsepower

@edwardberry9360 5 ай бұрын

ABSOLUTE PIECE OF FREAKIN' JUNK WITH A COMPLETELY WORTHLESS WARRANTY! - Mine is less than a year old, started smoking during operation, oil turned pitch black, and I thought, "Great, burned valve or wasted valve guide, okay, 'Three Year Warranty' though, right...?" WRONG! Even though the machine has less than four hours of run time, the dealership said that the valves were out of adjustment, and that would NOT be covered... I said, "Hang on... You're telling me this thing's engine is such a colossal piece of shit that they expect the valves to be out of adjustment after being run FOUR HOURS?" First piece of Cub Cadet Equipment... LAST piece of Cub Cadet equipment. Happily going back to Husqvarna... AVOID CUB CADET LIKE THE PLAGUE, THEY DO NOT STAND BEHIND THEIR EQUIPMENT!

@HillsideAcres 5 ай бұрын

Thanks for sharing, no issues here going on three years with no maintenance lol

@ralphfolden3273 6 ай бұрын

Thanks😀👍👍💪

@crawford323 6 ай бұрын

I ve got my manual 2501 set up with a 5' bush hog and a Lane Shark II ( a smaller 32' hydraulic powered bush hog) mounted on the front. This combination is formable.

@iamatt 6 ай бұрын

Been running 2 for 6 days straight here in Texas after Hurricane Beryl came through. Still running on them as I type. The 2000 is probably 23+ years old that I have no idea on the hours. The 22 hundo has 1100 hours. Really saving our asses down here at the moment.

@orpheusepiphanes2797 5 ай бұрын

Good to know man. Keep safe

@theoracle5265 6 ай бұрын

Thanks for this video and showing how and where to fill.

@Hopealwayswins 6 ай бұрын

Great review ~ bought a 50” today & this review mattered.

Ең жақсы KZbin

Пікірлер