Masashi Imamura

Пікірлер

@DivineroseconcinaPesimi 21 күн бұрын

Not work for me 😢

@mason2481 2 ай бұрын

This is happening to me. Drone isn’t stable with altitude above 20ft. Crashed straight into the ground when I enabled RTH

@89GTFoxDude 4 ай бұрын

Mine are dead. Can the battery inside be replaced separately?

@scottr3141 Жыл бұрын

I used 3 18650's 3500mah , soldered them in place of the original cells . had to velcro them to the battery case also. Then I unsealed the chip , reset it. After about 2 flights , the old batteries computer married pretty good with the percentage amount on the screen while flying. First flight , it said I had about 26% left, but the drone did a critical low voltage landing. Second flight it went all the way down to 15% which is the go home setting I have set. The battery's chip learned the new battery's capacity .

@sut2910 Жыл бұрын

Thanks great video!! I had a Spark battery that wouldn’t charge. After opening i used a cheap lipo charger on the exposed contacts to charge batteries one by one to ~3 v then tried it back on the DJI charger and it worked i was able to charge it!! Voltage was, 2.2, 1.9, and 2.2 when i opened it. Dji charger had refused to charge it prior to this. (Not a very smart charger/battery i guess). Thanks!

@NMCatfishing Жыл бұрын

How did you charge them once you took it out case?

@sut2910 Жыл бұрын

@@NMCatfishing I used a piece of foam with 2 nails thru it spaced the width of end contacts. Stood battery on end with nails touching a single cell’s contacts then jumpered the nails to a single cell lipo charger ( in my case a Traxxas Alias charger). I did not disassemble pack from end circuit card. I charged each cell separately to above 3v. When i put it back on the DJI charger it lit up like normal and charged. Center battery is opposite the polarity of two outer batteries. I used a multimeter when I opened it, cells were approximately 2 volts or a little less.

@cesarsilverio4168 13 күн бұрын

Yo should have posted a video

@fluidmind3629 Жыл бұрын

my battery is in hibernation mode, and i cant charge it. how i can put small charge direct to batteries and then try to charge with oiriginal dji cables...

@ZenMountain 2 жыл бұрын

What's the name of those tools you are using? Thanks?

@pradeepchannagiri Күн бұрын

You got the answer bro ? The names of tools ?

@teeodee4924 2 жыл бұрын

Thanks!

@AuroraColoradoUSA 2 жыл бұрын

I cannot tell what was done...

@imanuelbrian2273 2 жыл бұрын

kzbin.info/www/bejne/mGrMg6yIrp6Dnck mood batery mavic

@droneready8278 3 жыл бұрын

All the person really has to do is take care of their batteries the way that they're supposed to and the usual amount of charges and discharges that this drone can get is above 150 and up to 300 times if you just take care of the battery never store it fully charged even though it does discharge in 10 days never store it fully charged and only run it below 10% about every 20 to 30 flights to recalibrate the battery... After that anything else you do with it if the battery becomes bloated it's basically a flying bomb. 💯

@AuroraColoradoUSA 2 жыл бұрын

One of the great benefits of lithium batteries is they have extremely low leakage current and therefore are ready to use. I would just let the circuitry do its thing, as needed.

@ZenMountain 2 жыл бұрын

What a useful comment, thank you. Now we know what we have to do. Amazing.

@droneready8278 3 жыл бұрын

What happened to you man You have an uploaded any content and forever

@diegoskx2090 3 жыл бұрын

thanks for this tutorial. If someone is looking for a solution about inflated batteries, follow this tutorial and then pell out the black material under the battery, it can help to "desinflate" it, don't try to make a hole in the battery, it's very very dangerous.

@computerguy7213 3 жыл бұрын

next time hold the camers HORIZONTALLY

@agusbahagia5122 3 жыл бұрын

Now after opening it can anyone show us how to revive spark battery out of hibernation?

@spyder6000 3 жыл бұрын

Hmmm I will try what actually happens when those plastic coated wires touch the bottom of the metal plate (which contains the circuitory)????????

@ytkdmr 3 жыл бұрын

drop a little alcohol with a syrine and double sided tape will release itsself.

@dronezoom 3 жыл бұрын

Not work for me.

@Microfuture 3 жыл бұрын

Como seu voa com erro na bateria?

@frenky-tan 3 жыл бұрын

How this parot anafi prop holding on the sport mode? I seen other people did this the prop can't stand rpm for the sport mode. It snap off.

@Gw0wvl 4 жыл бұрын

The awful " Repetitive music " 👎👎👎

@pixelmolester 4 жыл бұрын

new set ot propellers worked for me

@arsyadtech 4 жыл бұрын

Great job friend. I will try it next time

@TheAkaimmaBoyz 4 жыл бұрын

I am facing same problem 😥

@arsyadtech 4 жыл бұрын

Great job. I will try this booater with my spark.👍

@omegalord 4 жыл бұрын

I wonder if this still works for the Mavic air 2.

@JaymeVanAuken 4 жыл бұрын

Yes very helpfull

@MattacksRC 4 жыл бұрын

Its a 3s. I wonder what all that fancy is circuitry is for.

@SethsPhone 2 жыл бұрын

To kill the battery when you dont use it ;). Oh and to make it a smart battery

@cezaryantuszewski5523 4 жыл бұрын

it does not work for me, I tried to do but it won't :(

@Simpleneazy 4 жыл бұрын

I want to put a normal lipo into one of my non working battery case... Connection how?

@hectorvp570 4 жыл бұрын

Same as te old one, but you will not find similar lipo cells that fits into the case

@AuroraColoradoUSA 2 жыл бұрын

nobody knows

@pavel1809 4 жыл бұрын

How do you clean the dji mavic air duster battery terminal??

@kisandrone 4 жыл бұрын

I have 3 spark batteries. First flight of the day with any one battery works just fine for complete 12 minutes. As i change the battery my spark starts hopping. I think it should be heating problem but its just guess. can anyone here tell me having the same issue?

@arkeung123 4 жыл бұрын

It works for my spark! Thanks a lot!

@seybr 4 жыл бұрын

You may have written down the battery serial numbers. Inside their number ? You can order Mavic pro by serial numbers from aliexperss. I don't know if they are to AIR.

@basilyok 4 жыл бұрын

Thanks! Just what I was looking for! Just one extra point I would make. When reassembling, it is best to pop the outer button out and pop it back in at the very end. Otherwise, the outer button can cause the inner button to get jammed.

@zantiagobaquero4064 4 жыл бұрын

SI VIDEO ES LO PEOR; DESPUES DE HACERLO NO VUELA EL DRONE ! QUE MALO QUE DEJEN ESTOS VIDEOS TAN MALOS!

@1981brenton 4 жыл бұрын

Thanks for the video , mine started this and I took apart and did as you said and all works well, thanks a ton. I could have sent it to dji because I ha a only had it lime 2 months but couldnt wait that long ..so my warranty is prob void but oooo well...thanks alot drone friend...

@rickyholman3116 4 жыл бұрын

Hi I have a dji mavic I’m in uk what do I need to buy everything to make it great booster and so on any links or email u can give me any advice would be great

@telebeater 4 жыл бұрын

So the booster antennas only allowed 3000 Meters? I can fly my Mavic Air 3500 Meters without any boosters. So my question is WHY BOTHER???

@joeregular1723 4 жыл бұрын

Exactly. I routinely get 3500 meters stock everything. Battery is my limiting factor.

@dzevad0101 4 жыл бұрын

hello, could parat anafi engines and propellers be installed on mavic air

@RedpillPortugal 4 жыл бұрын

Instead of increasing the weight of the battery, you should try to strip the drone so it will get lighter... Probably that way it would fly for a longer time. If you do this reply to this comment so I can check

@arunprakash8394 4 жыл бұрын

Hi bro.. my MA battery is not charging. The charging hub indicated red light. Is there any way to bring it back to life?

@cme7096 4 жыл бұрын

Please . I neet size zone inthe battery

@onyx8231 4 жыл бұрын

This REALLY helps. My spark overheated on a 85°F 29°C day. Average outdoor temperature in Texas. I drilled a big (1cm) hole in top cover above the cooling fan and it doesn't overheat anymore. Overheating causes crashes.

@jakabgipsz4788 4 жыл бұрын

Isn't it possible that this is not the problem that disappeared, but that you disassembled and reconnected the bottom sensor connector, which was badly contacted?

@kanehi 5 жыл бұрын

What would make the wires do that in the first place? Hard landings?

@kenwolfe6051 5 жыл бұрын

I followed your video and now my Spark flies like new! No more hop! Thanks

@carlosmartinvigovillalobos8574 22 күн бұрын

Que hicieron Pf mi spark tiene ese problema

@christophe9536 5 жыл бұрын

Hi, do you think i have the same problem ? Now Obstacle avoidance don't show anything... kzbin.info/www/bejne/sImYiXiBrN-Jf5I Thanks a lot for any answer

@christophe9536 5 жыл бұрын

Masashi Imamura hi and thanks a lot for your video. With your problem have you any information wrong in djigo 4 ? For me nothing but front obstacle don't work and hoppy spark with négative altitude when i start the motor. Before "operate" my spark i would be sure (ime calibration, compas, downgrade... nothing work and no crash). Thanks a lot for any answer

@christophe9536 5 жыл бұрын

I try it but no work for me :(((

@denojman 5 жыл бұрын

Love this video. I love the way you mavic air looks. What is the name of the company who made the skins? Thanks

@NaiburRahmanJoy 5 жыл бұрын

Thanks a lot It works. But I'm facing a new problem. I'm follow your step and now my spark is flying, but when i screwed all think my spark again jumping like frog. :(

@1981brenton 4 жыл бұрын

Take it back apart . I had same problem 1 my connections come off so I hot glued it back and now all is great...put a small dab on connectors very carfully

Ең жақсы KZbin

Пікірлер