Peace, Thanks Wildman. I've joined the club and this video helped a lot.

Thank you for dialing up this video. I have watched it so many times breaking down my K1 twice now. This last jam was 100% my fault, so stupid I don't want to repeat why it happened. I've learned rotating the mag before shooting and NOT using a speed loader has stopped the jams for me.

Thanks for this. It was hilarious, charming, and extremely helpful.

Use the .253 caliber. You want them nice and tight, I use Zan slugs 38 grain

I've only experienced jams when the pressure isn't high enough to send the round down the barrel.

Ha ha. All that fluffing just to get the mag out. Need an engineering degree 😁

Great vídeo, you helped to solve the problem, thanks

Hola le escribo desde España podía resolverme la duda si sirve para el modelo del 2023? Es que me han dicho que no es lo mismo y su carabina no sé de qué año muchísimas gracias de antemano y un saludo cordial.

Good time to clean the barrel without the magazine. Greatn informative video. Thank you

Did you know that all you need to do is drain the plenham by opening the regulator, this relieves the pressure on the mag and allows the jammed projectile to drop back into the mag, Remove the damaged projectile and re open the regulator to the correct setting you started with. These jams are caused by the wrong sized projectiles in the mag, they need to fit snug in the mag and not loose. You don't need to strip the gun like this and the issue can be rectified in the field in 5 minuets. It's very simple.

Chinese made, and NOT cheap. Before I gave that kind of money to China, I'd buy a European gun

It's way easier to have a rod that stops level with the mag and just slide it down the barrel and tap the slug back into the mag, It takes seconds.

This is one thirsty tutorial 🍻

Thank you for taking the time to make this and share with everyone!

sounds lie magazine alignment to me, i watched a vidio with a guy called gregor, there are two alignment screws to adjust but but he says it isnt a simple task.

Hi my opinion this new huben k1 mk2 its not good idea ,,, i prefer the versie 2 old verie

Looks like a blast.

I just got mine and was glad to see your video come up on my feed. I have not had that trouble and the gun is amazingly fun to shoot. I plan on only shooting NSA 38.5 grain slugs. I will tune a little but save the monkeying around to my FX rifles. I hope you solved the problem. Thanks so much for taking the time to help our fellow Huben K1 owners.

Has anyone figured what causes this. I have the same problem....

what a stupid gun. cant unload the magazine! these huben's are good examples of how people making airguns lose their head over hammerless design and other horseshit no one needs.

How do you make a b2s with a table that has no ROM?

Thanks good video

The couple of jams I had, long ago, I managed to clear by cutting the pellet in half, slipping spring shim stock through a narrow slot. Not sure if it was at the firing chamber or if it was close alongside.

It's most always a slug moving too far forward and binding on the front end. The cleaning rod works but you have to be careful not to push it back too far or it will jam on the back end. There's a little plastic ring on the back in front of the blast chamber with three little fingers and the slug can get giant jammed in between those three fingers if you push it back too far and too hard. Don't ask me how I know that:-)

do your pellets or slugs fit snug? They could be sliding too much forward...

How to take the pressure off the cylinder of this K1 model?

Excelente vídeo. Mas um escrito no seu canal do KZbin Excellent video. But one written on your KZbin channel

Great video, thank you. I read one should always push the pellets or slugs until seated; seen Gregor Kamensek do it to his own Hubens. Use a golf pin or the handle of a common lollipop, that ought serve the purpose. However, using larger projectiles in diameter will do well for the most part, not 216 or 217, but the 218 and larger. I never seen have any trouble with the JSB Monster redesigned in .22 caliber at 25.39 grains, which out to even 100 yds will be very precise and accurate. Thank you again.

A similar fail can happen when the two fat o rings behind the rear plate go bad. You'll pull the trigger and air will start blowing in your face, but you can turn the mag to stop the air. If you try again, it'll do the same thing, this means those o rings are bad, but it can also cause a jam. I just had to change the o rings on my 22 and a slug had jammed almost at the end of the barrel. Be sure to check your barrel if this happens. I have had to change them twice on my 2018 huben so far, so expect to have to change them every so often. You say 257 at the end of the video, if true I think that's too big, if 254 you should be good. Check your o rings behind the back plate maybe. I could see them going bad contributing to this type of jam. Seems like mine go bad every 2-3000 shots, but I'm always on high power, that may play a roll.

So how can this be avoided in this gun?

Plus I just subscribed to your channel and your number didn't go up???

Boat tailed slugs, 22 cal 35 gr large .. .218 dia body) .233 sealing ring 100 count. Same exact everything except in small .217 25 cal 47 gr (.250 dia body ) .253 sealing ring- 100 ct. order from New England Airgun phone number 1- 978-567-6970 Also if when your mag is spinning and you feel any catching, take a small nail using the head end an seat the pellets or slugs in as to not rub !!! But with these slugs I've told you about you'll have no issues ! Buy better slugs, think your gun cost 1400 or 1800 depending on where you got it so spend the extra bucks for the better correct ammo. By all means I'm not saying you haven't, but some even costly ammo isn't correct and cheap ammo isn't worth it unless when you call that number they say so!!! Let me know your results

Really detailed and informative video. This has happened to me a few times and I've actually been able to carefully push the slug back into the mag with a cleaning rod from the the muzzle side. They do jam really hard but it's doable.

I know. Your slugs are not large enough diameter. Your Huben does best with. 253 or max. 254. Most common slugs like JSB or Knockouts are 250 and 251 respectively. Smaller slugs will fall into the barrel if you tip the gun downwards. It will still fire, however. One more possibly is your slugs are to big diameter and not seated into the mag enough.

牛逼

Thanks for this tutorial. I've just made my 1st backglass for the Daft punk table. It's very basic but all working

Thank you for the video sir, still being used :)

Awesome tutorial! Time to start playing!

The dog did play but didn't harm it :).

Yes please do another one, it's great! :).

Thank you :). This is a nice tip! All i do for the time is to import back glasses and figuring out what these elements are and how they work, like the ID's sort of lightning etc... It is tedious as F. Most of it is obvious, however i won't to make a back glass adding a fantasy image, first who made a back glass like that...(looking things up may save a lot of time, or may confuse you) . Once again Thank you very much for your help!

Yes those new PCP big bore are powerful not like our old pump action crossman .22 🤣 he fired that new PCP big bore 9mm with 150 foot pounds of energy in a semi automatic and said WOW yeah those are 81gr at 920 fps muzzle velocity🤣 that's more than Human Deadly Sir 4 Sho ✊✌️

Thanks for the great video Wildman, always enjoy your backglasses. And is just me or does Wildman sound like Tony Soprano... ; ))

i know this is pretty old, but thank you for this video. i created my first db2s today because of it. thanks!!