2 ай бұрын
7 ай бұрын
8 ай бұрын
Пікірлер
@xXMOTOXPYROXx 4 күн бұрын
Could I just run a ground wire from pgm 1 and positive from Aux + to a led controller I have to trigger led lights when the house alarm comes on? And configure that in the dsc keypad
@AlarmSystemStore 2 күн бұрын
Yes, as long as the relay can be powered by the 50mA @ 12V that the PGM supplies, that would work fine. The main issue with PGM1 or other low current PGMs is finding devices that can use that small amount of power, but if you can work that out you can accomplish many handy tasks with PGM outputs.
@XsavioR38 4 күн бұрын
wait 20 mins , it goes away
@AlarmSystemStore 2 күн бұрын
This isnt always the case, but yes, sometimes you just have to wait for the sensor to catch up and notify the panel things are all good. Patience doesnt come easy to everyone though lol
@eshrilildharrie863 10 күн бұрын
How do i replace a transmitter on a interlogix nx4 nx6 . Your video shows how to add a transmitter . But it fail to show how to give zone name and zone type . And how to replace a transmitter . Please make a video how to do it because ther is no tech support for this panel .
@AlarmSystemStore 9 күн бұрын
The existing videos from back when this panel was in service are all we have for the NX systems. Its been long discontinued and we dont have an NX system anymore, so we have no way to make any other videos on it. The best advice I can give is to use the installation manual along with whatever info you can glean from the existing videos.
@Charlie-Raphael 11 күн бұрын
What is the switch address setting for a secondary zone expander ?
@AlarmSystemStore 10 күн бұрын
You'll use address 8. Start with 7 for the first expander and go in order. The small paper that comes with the expander shows the dip switch settings, but if you dont have that, you can find it here towards the bottom of the doc: cdn.shopify.com/s/files/1/1659/9809/files/4219-without-EOLR-option--Installation-Instructions.PDF?415632166615481284
@Charlie-Raphael 10 күн бұрын
@AlarmSystemStore Thank you for your time
@najeebrehman7043 15 күн бұрын
The video really starts after wasting 2 and a half minutes
@AlarmSystemStore 12 күн бұрын
We appreciate you wasting your apparently precious time to post this comment. Its hard to fathom the number of people your insightfulness will help down the road.
@MarieHoward-h8t 16 күн бұрын
Hey mine doesn't have the "system required" on it which one should I do?
@AlarmSystemStore 12 күн бұрын
The system required is just the set of trouble directly related to the main system. Troubles can be related any device connected to your system, so the majority of troubles will not display "system required". You'll just need to identify which module the trouble is indicating which is covered in the video.
@fernandoconforme4746 17 күн бұрын
Por favor me ayudas a instalar mi camara de esas la vc728pf
@JLC8088 22 күн бұрын
My smoke detectors are 10+ years old and needing to be replaced and I have almost this exact same setup with a DSC PC1616 and System Sensor WTAB's. Can I simply order new WTABs to replace the old ones, keep the already-wired mounts in the ceiling and simply swap out the old units for new ones?
@AlarmSystemStore 22 күн бұрын
Yes, to my knowledge the mounts have never changed for the i3 sensor group.
@Rogue_gorilla_0 26 күн бұрын
This year at the isc show they were showing off their Power G + but I can’t find anything on it do you have any info on that!
@AlarmSystemStore 23 күн бұрын
The name has been tossed around a bit, but nothing concrete as of yet to my knowledge.
@vicatt1038 27 күн бұрын
Can you replace the battery with a power adaptor 3.6Volts output same as the battery? The battery does not last that long especially if you have a couple of false alarms
@AlarmSystemStore 26 күн бұрын
It was not designed for that style of setup, so no I do not believe that would work.
@jcnash02 Ай бұрын
7:20 makes it seem like you can pre-configure a panel Occupancy sensors are for home automation
@AlarmSystemStore Ай бұрын
The configuration download is done through Alarm.com, without a panel being activated Alarm.com doesnt provide a way to pre-configure anything. In theory though, yes, you could pre-activate a panel and set a few things up via Alarm.com prior to installing the unit, but the majority of the programming would need to be done at the panel.
@gogeta724 Ай бұрын
Hi. I need the app. Please
@AlarmSystemStore Ай бұрын
You can download the app at any time from an app store, but to have a login you will need to sign up for Alarm.com service. You can check the plans we offer on our site www.alarmsystemstore.com/
@denniskaram3102 Ай бұрын
Great video
@donniearthur8667 Ай бұрын
why would u tell me to call u on a fb page? then the girl not help?
@AlarmSystemStore Ай бұрын
No idea what you're talking about. We only have one female here in accounting dept, but she doesn't answer the phones. If you're our customer you need to open a tech support ticket here: www.alarmsystemstore.com/pages/tech-support We respond to these within 2 hours during business hours and it's the fastest way to get help.
@donniearthur8667 Ай бұрын
Man im stuck.. I cant get past a enter user # and wont let me enroll either. tryed manual and using the * on the fob :( can u could u help me. please
@AlarmSystemStore Ай бұрын
Which user # are you referring to? Are you unable to enter programming? If thats the case you wont be able to enroll any sensors.
@HenryA.Thomas Ай бұрын
How to fix RF Jam Trouble and Swinger Shutdown? I have replaced the battery and reset the alarm. Thanks
@AlarmSystemStore Ай бұрын
The RF jam indicates an issue with the receiver having signal issues, but its a bit much to try and work through in a YT comment. If you're one of our customers you can open a tech ticket on our site. Otherwise it would probably help to have an installer take a look at it.
@HenryA.Thomas 23 күн бұрын
@@AlarmSystemStore Thanks! What is the cost and do you have an installer to recommend.
@maried157 Ай бұрын
Thank you for this. Very helpful. I’m having issues with my entry. I don’t hear Beep. Is there a setting to turn the beeps on when you enter the home?
@AlarmSystemStore Ай бұрын
The IQ panels generally speak the name of the sensor opened. You'll need to check the volume of the panel in the drop down menu to make sure it is turned up. If the chime has been turned off though you will need the installer code to enter programming and enable chimes.
@jcnash02 Ай бұрын
Wow! That thing is huge! I would love to hear your thoughts on the new Vista H3
@AlarmSystemStore Ай бұрын
Id love to take a look, but we tend to not be able to work with much Honeywell and Resideo equipment. They make everything so proprietary, and being a DIY dealer a lot of the options they provide just do not offer the flexibility we try to offer our customers. After a quick google search it looks like the H3 uses the PROSIX sensors, which proved problematic for us because of the way they lock to the system they are enrolled on initially, so its unlikely we'll ever check it out. If I do though we'll definitely put a vid up about it!
@talvindermohein6125 Ай бұрын
Sir My dsc stuck in armed . Forgot the code to disarm . Installer code not work either . What should I do ?
@AlarmSystemStore Ай бұрын
Without knowing more information, there isnt much I can say. The system will require a valid code to disarm. You could potentially default the system, but if you didnt program it, youd be in for a good bit of work.
@joncruz Ай бұрын
What resistor are you using in this panel? The 2k or dsc 5.6
@AlarmSystemStore Ай бұрын
We're using a Honeywell system, so they are the 2K resistors plus the unique resistor that comes with the COSMOD. The resistors you put on the COSMOD terminals will always be the resistor that the panel your working with needs. The End of line resistor on the sensors is the COSMOD resistor.
@joncruz Ай бұрын
@ so both resistors (the one that comes with the system and the one the two that goes in the module) should be the same value?
@Yabo- Ай бұрын
I don’t love the app programming. I’m much faster with a laptop/ keypad. I’m most interested in the addressable portion as it’s the only reason I use vista still
@AlarmSystemStore Ай бұрын
I think youd be pretty surprised with the IQ Pro programming, after a short programming session the only time consuming part of the app programming is letting it run its diagnostics when you first connect. After that you just enroll and set the zones and thats all you have to do to get started. Obviously there are other settings that you can edit if needed, but we were very impressed with how quickly it went. We'll have a video up on it soon. Addressable sensors however may not be shown since Im not sure if we will carry them. We'll try to cover them if we can though.
@Yabo- Ай бұрын
@ I found the app good if you were going to pre set up the system and then deploy. This was in the beginning of the year when the Neo had a recall due to the bad firmware/corbus issue. I do like your videos though. Keep at it.
@jmonte8056 Ай бұрын
Hello, Very Nice video! Question: One of my smoke detectors has gone bad (it's a DSC4936). Can i just buy a new one and program it to replace my defective one? Thank you.
@AlarmSystemStore Ай бұрын
If you have access to the programming of your panel then yes. However, the WS sensors have all been discontinued so it might be difficult to find a replacement.
@ls2guy Ай бұрын
I’ve installed 1000’s of PowerG devices and the PG9984P is hands down the worst for “low battery” conditions to clear. Even after deleting the device and reinstalling it. A week later, “Device Low Battery”. I’ve complained to JCI tech support and of course they play dumb. Never had this problem with the cheaper PG9914.
@ZAFARKHAN-eb4wl Ай бұрын
How did you clear battery problem?
@AlarmSystemStore Ай бұрын
It depends on what exact battery problem you have, but generally replacing the referenced battery and power cycling the panel will clear the trouble.
@RinasAnwar-j4n Ай бұрын
Why the partition for?
@AlarmSystemStore Ай бұрын
Partitions allow you to have multiple small systems using a single alarm system essentially.
@handlers753 Ай бұрын
How do you program a 2-wire smoke for delayed 24-Hour Fire. When my smoke is activated it goes into immediate alarm which is not desired in cases where burnt toast sets off the smoke.
@AlarmSystemStore Ай бұрын
2-wire smokes cannot be set with a delay unless the system specifically offers that feature. Im not sure of any systems offer that, but the DSC and other systems we carry all have instant trigger on 2-wire smokes. You would need to use 4-wire smokes if you wanted to have a delayed trigger on smoke detectors. Generally its better to use heats in the kitchen rather than smokes, so you might think about replacing whichever sensor is being triggered that way.
@handlers753 Ай бұрын
@AlarmSystemStore thank you. Appreciate it
@LykeArgy Ай бұрын
Really nice video, i started as an apprentice electrician but our boss also does security so i got into that, this video helps a ton, but i do have 1 question, if the System calls for 1100 ohm resistor what would happen if i were to use 1000 ohm cause i'm out of 1100? (i'm not gonna do this, we'll just wait for the order to come and finish the job some other day)
@AlarmSystemStore Ай бұрын
It depends on the tolerance of the system. Either way it wouldnt hurt anything to put it on, but if the tolerance doesnt allow 100ohm difference then the system will not see the right resistance rating. For example if it were a zone, the zone would show a fault just as if the resistor were not connected.
@LykeArgy Ай бұрын
@@AlarmSystemStore Yeah was told the same thing today by a guy who does this for 12 years, said 1 might not hurt but we're putting 2 so that would be 200ohm differnece and wouldn't wokr, thanks for the response =)
@vanatoj Ай бұрын
How does this device connect to the internet?
@AlarmSystemStore Ай бұрын
It includes an ethernet dongle that you can run a cable to.
@matthewmusselwhite591 Ай бұрын
Safe Haven removed/deleted the Installer user from my IQ4 panel and I am not able to install any devices or remove anything.
@andybowman9697 Ай бұрын
That's one of the many advantages of DIY. You own all the codes. Unfortunately it's not uncommon for installers to not provide installer codes and is a big reason why we exist today as a DIY supplier of pro grade security equipment.
@nickday3541 Ай бұрын
Bought my house 6 months ago and was told that the alarm was disconnected. Let the dog out last night and the house alarm went off very loud. Alarm system shows a yellow triangle & red lock locked. Also, bypass & stay.. Can I cut the alarm speaker wire up in the attic if I can't reset? Nothing on my main panel saying it's hooked in but it must be hard wired in somewhere as there is power even though the small battery is disconnected..help!😝
@AlarmSystemStore Ай бұрын
The better option would be to find the transformer plugged into the wall providing the system power. With that and the backup battery disconnected the system will turn off.
@treborg777 Ай бұрын
Just found this video. I’ve purchased a house with this system, and the previous owner gave me the owner code but not the programming code. How can I reset the programming code?
@AlarmSystemStore Ай бұрын
You will need to backdoor into the systems programming. It should be pretty easy to find the process with a google search.
@treborg777 Ай бұрын
@ thanks for the response. I’ve seen at least one video about this (I think), that involves removing battery & AC power.
@hosseinnabavi5403 Ай бұрын
Thank you for your video. I have a Vista 48A/48E, and the LEDs on the keypad are dead, but there is a backlight on. The battery voltage is 13.5V. Should I replace the main board? If yes, what is the most updated version compatible with WiFi? I am not sure how to troubleshoot it. I have tried to disconnect the battery, as well as AC power to reset the unit, but still getting Fault 05. For a while I was getting Fault 04, but I only see Fault 05 on the keypad Could you please kindly help?
@AlarmSystemStore Ай бұрын
We're not familiar with the Vista 48 models, so we wouldnt be much help there. If you wanted a fresher system though, you could go with a 20P, or move to something more modern than Honeywell like the DSC NEO system. Both are hardwired so you should be able to keep any wired sensors you currently have.
@carolgerson3031 Ай бұрын
How do I get to the menu that allows me to change the disarm delay time?
@AlarmSystemStore Ай бұрын
It is in the security and arming section at the end of this video.
@MichaelSzolusha 2 ай бұрын
These sirens are garbage, you'll agree when it's 0 degrees out and your waiting 40 m for dam thing to beep 🤦♂️
@AlarmSystemStore Ай бұрын
The older WT wireless sirens could definitely be troublesome, but they upped their game for the newer DSC NEOs wireless sirens. The batteries don't require depassivation and they've performed flawlessly for us for years since they released.
@rjmalerman 2 ай бұрын
Thanks man! Really helpful video!
@MattLevin-q9n 2 ай бұрын
What size battery is needed for the 4911B blue strobe? Can it be purchased at a local hardware store?
@10AK10 2 ай бұрын
My window sensor went "not networked" after a power outage. Tried triggering a tamper, taking the battery out, doesn't change anything. Ideas?
@AlarmSystemStore Ай бұрын
Sorry for the delay, but if the normal methods do not work, the only option is to delete the sensor and re-enroll it by using the auto-enroll method to force the initial connection.
@douglasbelew6573 2 ай бұрын
The secondary panel in our primary bedroom auto lights every morning at 6am. A feature I don't appreciate. Is there a way to stop this from happening or change the time to later in the morning?
@AlarmSystemStore 2 ай бұрын
Not to my knowledge, but all IQ remote diaplay options can be viewed under settings in the drop down menu. I havent witnessed this myself though. Are you sure there are no events happening at 6am? Such as an auto-disarm or something similar?
@BradleyLivestreams 2 ай бұрын
Fantastic video, thank you! New subscriber here. My old Honeywell system stopped responding to keypad commands a week ago all the sudden. I press my normal codes to arm, disarm, etc... and nothing. The buttons do beep when pressed, but the system doesn't respond. And the door open chimes stopped "chiming" at the same time. The system was working for 10+ years before a week ago, so odd. Gonna check out some of your other videos. 👍
@AlarmSystemStore 2 ай бұрын
Glad you enjoyed the video. You might check the wiring for the keypad. The yellow and green wires transfer data back and forth to the system, so one of the wires may have an issue.
@nickleblanc7190 2 ай бұрын
Great video and very informative! It solved my sensor issue. Thank you very much
@hockeyman1 2 ай бұрын
mine triggers the alarm without any water in the crawl space. what can be the issue?
@AlarmSystemStore 2 ай бұрын
It would have to be a wiring issue if there is no water at all. These detectors trigger when they are shorted, so if your wires are pinched somewhere, or if perhaps a mouse is picking at the wires, that could short the wires and create a false alarm. If you can I would just check all the wiring connections, and if possible inspect the rest of the wiring.
@wagnerfamily4229 2 ай бұрын
Thank you for this video.
@AlarmSystemStore 2 ай бұрын
Glad it was helpful!
@billcrystal 2 ай бұрын
My alarm is going off with four beeps. I replace the battery already now I don’t know what to do.
@AlarmSystemStore 2 ай бұрын
The Simon is long discontinued so we couldnt give any specific instructions, but if its still beeping you may have a different trouble condition at play other than just the battery. Its also helpful to perform a power cycle on alarm systems as that clears troubles unless they are still present.
@mooew 2 ай бұрын
On the jobsite alone for the first time i love you thank you for helping me keep mu job
@Samlol23_drrich 2 ай бұрын
So I have (multiple series) loops and each loop contains magnetic window switches, as well as shock sensors in between the (Anderson style) windows. I can’t wrap my head around how that works. Honestly nobody has ever set off the shock sensors and I’m not sure they are doing anything. I took a multimeter and isolated one shock sensor. There are 4 wires, but the installer only used two of them. There’s continuity between the wires. When I hit the sensor it very briefly fluctuates ohms, but within a second, there’s continuity again. Can something like this actually work? A split second change in resistance? It’s an older ademco vista 20 system. Any info would be greatly appreciated.
@AlarmSystemStore 2 ай бұрын
Most systems have a response time of less than half a second, so yes it should work fine, though its designed to catch a window breaking, so they can sometimes take a decently good hit before triggering. Otherwise youd run into false alarms. Its a bit unique that your shock and contact sensors are all wired in the same loop, but they're all 2-wire sensors, so they should all just be wired in series.
@Samlol23_drrich 2 ай бұрын
@AlarmSystemStore Thanks very much for your response. I appreciate it.
@TXsanta 2 ай бұрын
Well good luck to anyone not sitting in front of the device or who doesn't have super vision...Just decided not to talk this time?
@AlarmSystemStore 2 ай бұрын
Are you having trouble hearing the audio? The whole video has dialogue. You might need to check your sound/speaker settings.
@lindamast2512 2 ай бұрын
how do I use smart alarming without sound. I don't want to hear when the alarm system automatically disarms at the time I have set.
@AlarmSystemStore 2 ай бұрын
Are you referring to the system or the app?
@jeradcampbell4359 2 ай бұрын
Tell me why I did a certification class in this, but the KZbin video taught me more than the class itself
@sandywilson8921 3 ай бұрын
FYI, this device will transmit in 4/2 format.
@chrispflug8567 3 ай бұрын
This system stinks. An example of bad and annoying technology. Trying to do too much on a small screen. Not user friendly. Will be ditching the one I inherited from the prior homeowner.
@AlarmSystemStore 3 ай бұрын
It definitely didnt keep up with the times, however if you're looking for a nice wireless system, the Qolsys IQ Panels are very modern and feel great to use.