Where did you get the assembly for the motor mount
@aaronpratt892 күн бұрын
@@Deerhitter7729 it’s manufactured by GoPed. Its the 54mm motor mount
@drippinginswagАй бұрын
very helpfull ive watched a few times now i am installing my 3rd bearing and lockdown kit tomorrow on the same exact go ped along with a 750 black magic spindle thanks for videos keep up the good work my friend
@aaronpratt89Ай бұрын
@@drippinginswag I’m glad I could help!
@drippinginswagАй бұрын
i love your videos man so helpfull hope u make more =)
@aaronpratt89Ай бұрын
@@drippinginswag I pan to make more, just have a lot going on in life right now haha. Thanks for the support!
@drippinginswagАй бұрын
@@aaronpratt89 i feel ya brother n yw!
@MmmHugglesАй бұрын
I bet if you replaced the spark plug with a glowplug to get it started, you could convert a small 2 stroke to diesel. Run the glow plug long enough for the engine to warm up enough then it will run on residual heat.
@aaronpratt89Ай бұрын
@@MmmHuggles I had that same idea. However I never managed to get this engine hot enough for it to run on its own. I could make an adapter to use a small nitro glow plug and see if it works
@chadr00Ай бұрын
Cut the metering spring is something I hadn't heard of. I bent the metal piece holding the needle so that it opened sooner. It helped to add more fuel but it wasn't easy to tune accurately. It was often too rich on low and mid throttle. Does cutting the spring shorter have the same negative effects?
@aaronpratt89Ай бұрын
@@chadr00 raising the fulcrum doesn’t change the pop off rate. It actually changes the timing. Pop off rate is the amount of pressure required to push the needle open and pressurize the diaphragm area of the carb. By raising the fulcrum you risk over pressurization and the seat never closing. Sounds similar to why you had a hard time tuning it and it running rich. By cutting the spring the fulcrum can stay closed when not being used and still open at the correct time while allowing more responsive fuel delivery.
@randallhamrick1800Ай бұрын
I'm glad there are still young men with imagination. Good video son.
@sdonovanpАй бұрын
How many cc is that engine?
@aaronpratt89Ай бұрын
@@sdonovanp 22.5cc
@DanielGonzalez-bn3ywАй бұрын
I can’t get my ped running with the lockdown kit :(
@codiebiggans48752 ай бұрын
I have some questions. You seem to be the guy who may have the answers lol I'm working on my red goped sport, I believe it's a Gen2... Anyway I have a cy27 engine I put on it but I can't run the stock exhaust, it doesn't fit the sport.. also would the ada clutch kit benefit me? Cause it seems to me it makes it slower by the videos I've seen but not sure.
@alterdcustomrc45122 ай бұрын
I watched it over 2 weeks, haha subscribed
@aaronpratt892 ай бұрын
@@alterdcustomrc4512 hell yea!
@dawmanchannel28372 ай бұрын
awesome build, thank you for sharing this with us
@aaronpratt892 ай бұрын
Thanks!!
@angeltaaga252 ай бұрын
sweet video! recently got a bigfoot and looking to do some upgrades
@wheeliedad902 ай бұрын
Thats sick man wish you loved closer to me.
@Eduardo_Espinoza2 ай бұрын
Can't wait :)
@longliveskully2 ай бұрын
Let’s go!!!!!! More uploads 🍿
@aaronpratt892 ай бұрын
They are coming!!!
@phatboy42732 ай бұрын
Hey bud would you be interested in going through and tuning a 460 for me I'd pay you for your time if possible
@markallenarcano94392 ай бұрын
Present Bro from the Philippines 🙋
@aaronpratt892 ай бұрын
Hello!
@Eduardo_Espinoza2 ай бұрын
1:30 & 2:00 You can probably save your frame from cuts! Instead of a gusit, you cud probably put a door hinge & save your current clutch, with a Chinese one & make it extra compact w/the new hinge :D I'm just spit balling tho & seeing what sticks!
@Eduardo_Espinoza2 ай бұрын
Are you going to cut off the red tubing just around the engine later? :)
@aaronpratt892 ай бұрын
I will probably just leave it. It would make a great base for a pipe mount
@markallenarcano94392 ай бұрын
Present Bro from the Philippines 🙋
@Fotopro2 ай бұрын
Thanks for the reply. I’ll keep an eye out for the video.
@longliveskully3 ай бұрын
Come on brother! More than 2 vids a year let’s get it going!!!
@aaronpratt892 ай бұрын
I’m doing my best 🤣
@SuperJiggawhat3 ай бұрын
Awesome video. Please make more 🙏
@aaronpratt892 ай бұрын
I have my camera back out I have a few videos to edit and upload! Thanks for the support
@cheesecake93363 ай бұрын
9:38 that thing ain’t connected! The spark plug what?
@aaronpratt892 ай бұрын
its connected the kill switch is dosconnected lol
@cheesecake93362 ай бұрын
@@aaronpratt89 o
@Eduardo_Espinoza3 ай бұрын
First like :D A weird way I'm looking at it is Body mounted engine, extended chain + spring tensioner.
@aaronpratt893 ай бұрын
I have a few compact clutch designs that I am working on with a machinist 😎
@rabbitfootedkitty13393 ай бұрын
When Goped will eventually stop producing the go quad. Glad to see you back with another video!
@aaronpratt893 ай бұрын
I appreciate the support!
@StroDshiesty13 ай бұрын
Would a hda 223 be okay on this? (Internal pulse)
@aaronpratt893 ай бұрын
Possibly. Just need to find out if this cylinder has a pulse for a modern card
@StroDshiesty13 ай бұрын
@@aaronpratt89 ah yes i remember you saying that in the video
@Eduardo_Espinoza3 ай бұрын
Idk, but thanks for sharing :)
@aaronpratt893 ай бұрын
Hey, thanks for being here!
@markallenarcano94393 ай бұрын
Present Bro from the Philippines 🙋
@aaronpratt893 ай бұрын
Thank you!!
@YoMamazYT3 ай бұрын
Remeber when you did those alternative fuel videos could you try 91 percent isopropyl alcohol?
@aaronpratt893 ай бұрын
Yea! I need to get back to doing those! I have a whole list of requests!!
@BryanAmrey3 ай бұрын
Video sucks can't see shit
@christophersherman90913 ай бұрын
Hey Aaron… any chance you would be willing to sell me a rockit key for a g23lh?
@aaronpratt893 ай бұрын
Just buy the RC coil. It has better results and a better timing curve
@hamalatsubuh48673 ай бұрын
Does the vegetable oil have the same point of burn like diesel?
@aaronpratt893 ай бұрын
That I am not sure of. You make be able to determine that if you look up the SDS sheet on the oil and compare it to the fuel
@Undertaker1134Tx4 ай бұрын
I used to used nitro in my old tomos moped. Had to use a 125cc dirt bike carb to get it going right.
@michaelmilligan72914 ай бұрын
Bro how do you put the motor to the frame I can't find not one video on it
@aaronpratt894 ай бұрын
It’s on the mini bike lol
@michaelmilligan72914 ай бұрын
@@aaronpratt89 there isn't one video of how install this to goped frame from 90s that is came on
@michaelmilligan72914 ай бұрын
@@aaronpratt89 can you show motor mount bolts
@aaronpratt894 ай бұрын
@@michaelmilligan7291 it mounts using the m6 screws like all small bore gopeds. Same as the sport and big foot.
@michaelmilligan72914 ай бұрын
What bolt did you use to mount the motor to the frame
@aaronpratt892 ай бұрын
Which area are you asking about? The motor mount to the frame? I used the stock bolt that was already on the machine. The engine to the motor mount? I used M5 allen bolts.
@Suhgondeez4 ай бұрын
The carb on my go-ped is leaking gas…. Any idea why that would be?
@aaronpratt894 ай бұрын
What kind of carb do you have?
@Fotopro5 ай бұрын
Aaron, is the a special spindle needed for the ADA 3rd bearing? I ordered the “long spindle” recommended by DDM and it’s really short, and only extends 1/2 way across the rear tire. My previous spindle extends almost completely across the tire. Can’t I just reuse that?
@aaronpratt895 ай бұрын
Did you order a long drive spindle for a sport or big foot? They are different. You need to order the one specific for the Ada 3rd bearing.
@Fotopro5 ай бұрын
@@aaronpratt89 I think that was it. I confused my order and got a sport spindle. 🤦🏻♂️ Thanks
@goped.on.scooters5 ай бұрын
Keep them videos coming 🔥
@aaronpratt895 ай бұрын
I’m going my best lol I appreciate the support!!!
@goped.on.scooters5 ай бұрын
Interesting !⛽
@aaronpratt892 ай бұрын
we could use some more of hose today for rc engines too!
@Fotopro5 ай бұрын
You did notice the tire rubbing when you did the lockdown install video. You were like “hmm, it looks like the tire is rubbing or something”. But then you just moved on. 😂
@aaronpratt895 ай бұрын
That sounds about right 🤣🤣
@weed37145 ай бұрын
Arrow goes to the exhaust port not the intake
@aaronpratt892 ай бұрын
Yes that is the case. The ports on this engine are so small the ring gap can be on either the intake or exhaust. Luckly the piston pin is not ofset in this engine.
@P00katube5 ай бұрын
0:37 She'll go 300 hectares on a single tank of kerosene!!!!!
@user-qb1km2fl8s6 ай бұрын
I love 2 stroke smoke to smell best smell ever i wish i can run it everyday and it just smell it
@user-qb1km2fl8s6 ай бұрын
This is good experiment to run is whole day and smell the fumes if you love diesel smoke smell
@user-qb1km2fl8s6 ай бұрын
Would love to smell it must have smell great
@jasonthomas2886 ай бұрын
Really at what point did he run it off of diesel. He used kerosene and 2 stroke oil.
@aaronpratt892 ай бұрын
when i filmed this video I thought they were the same fuel. I have leaned sonce then the highly refined kerosene has very different combuston rates and behaviours.
@Fotopro6 ай бұрын
What are the benefits of lightening the flywheel? Does it really make a big difference, or is it over hyped?
@aaronpratt896 ай бұрын
Less weight in the flywheel helps the engine rev faster. Downside is you lose some torque.
@Fotopro6 ай бұрын
Will the ADA 3rd bearing motor mount work with the factory frame spring? I’m considering just upgrading the motor mount and using the cable to still lift the motor off the tire. .
@aaronpratt896 ай бұрын
I believe it will! The motor mount has a place to mount the original clutch cable also.
@Fotopro6 ай бұрын
What pipe is that? It looks nice and compact. . I’m looking to replace my X-Can.